installation instructions W10694025 RevD

ManualsBrandsMaytag ManualsAppliances30 in. 5.8 cu. ft. Gas Range with True Convection in Fingerprint Resistant Stainless Steel

3. Apply masking tape to the end of a 7 mm (⁹⁄₃₂") nut driver to

help hold the gas orifice spud in the nut driver while changing

it. Press nut driver down onto the gas orifice spud and

remove by turning it counterclockwise and lifting out. Set gas

orifice spud aside.

4. Gas orifice spuds are stamped with a number on the side.

Replace the LP gas orifice spud with the correct Natural gas

orifice spud.

Refer to the following chart for the correct Natural gas orifice

spud placement.

4" WC Natural Gas Orifice Spud Chart

5" WC Natural Gas Orifice Spud Chart

NOTE: Refer to the model/serial/rating plate located on the oven

frame behind the top right-hand side of the oven door for proper

sizing of spuds for each burner location.

5. Place LP gas orifice spuds in plastic parts bag for future use

and keep with package containing literature.

6. Replace the burner base using both screws.

7. Replace burner cap.

8. Repeat steps 1 through 7 for the remaining burners.

To Convert Oven Bake Burner (LP Gas to Natural Gas)

1. Remove the oven racks.

2. Remove 2 screws at the rear of the oven bottom.

3. Lift the rear of the oven bottom up and back until the front of

the panel is away from the front frame. Remove from oven

and set it aside on a covered surface.

4. Remove 1 screw from the bake burner.

5. Slide the front of the bake burner to the side to remove tab

from front of oven. Lift the back of the bake burner off the

oven orifice, and set the bake burner aside.

6. Using a ³⁄₈" nut driver or combination wrench, turn the LP gas

bake burner orifice spud counterclockwise to remove. The

spud will be stamped with a “56.”

7. Replace the “56” spud with a “47” spud. Install the Natural

gas bake burner orifice spud, turning it clockwise until snug.

IMPORTANT: Do not overtighten.

A. Orifice spud

B. Orifice spud holder

C. Screw

D. Spark electrode

A. Stamped number

Burner Rating Color Size ID Number

18,000 BTU

17,000 BTU

15,000/15,500 BTU

14,200 BTU

13,000/13,500 BTU

12,000/12,500 BTU

9,500 BTU

8,000 BTU

5,000 BTU

Yellow/Blue

Red/Magenta

Red/Black

Red/Orange

Red/Blue

Red/Yellow

Red/Brown

Red/White

Red/Brass

2.16 mm

2.10 mm

2.00 mm

1.90 mm

1.85 mm

1.80 mm

1.55 mm

1.40 mm

1.10 mm

N216

N210

N200

N190

N185

N180

N155

N140

N110

Burner Rating Color Size ID Number

18,000 BTU

17,000 BTU

15,000/15,500 BTU

9,500 BTU

8,000 BTU

5,000 BTU

Red/Black

Black/White

Red/Yellow

Red/White

Red/Green

Blue/White

2.00 mm

1.94 mm

1.80 mm

1.40 mm

1.32 mm

1.04 mm

N200

N194

N180

N140

N132

N104

XXX

A. Screws

B. Oven bottom

A. Screw

B. Bake burner

A. Orifice spud