Installation guide
INSTALLATION
30”
WALL
OVEN
DESCRIPTION
Built-In
30”
Electric
NEw
eeiileus(e)\ig
Combination
Wall
Ovens
403
WEST
FOURTH
STREET,
NORTH
NEWTON,
IA
50208
COMBINATION
WALLOVEN
CUTOUT
1
1-1/4”
Dia.
Conduit
Access
Hole*
2
5/8”
Plywood
Floor
(Must
Support
250
Ibs.)
DIMENSIONS
in
cm
A
30
MIN
76.20
MIN
B
24
MIN
60.96
MIN
C
47
+1/16
119.38
+
16
D
24
MIN
60.96
E
28-1/2
+
1/16
72.39
+
.16
F
47-5/8
120.97
G
29-3/4
75.57
H
24-7/16
62.07
|
4
to
20
10.2
to
50.8
*
Hole
must
be
cut
as
close
to
corner
of
cabinet
as
possible.
|
Z
|
Do
not
block
air
intake
slots
along
bottom
of
oven.
|
INSTALLATION
1.
Cut
hole
in
cabinet
to
mount
oven.
Cutout
in
cabinet
should
be
level
and
straight.
NOTE:
There
are
no
provisions
to
level
the
unit
after
it
is
installed.
An
oven
that
is
not
level
could
cause
poor
baking
results.
.
Install
plywood
floor as
shown
above.
.
Install
top
mounting
bracket
-
also
refer
to
template.
(figure
3)
Top
bracket
mounting
installation
instructions:
a.
Before
installing
unit into
the
cabinet,
open
microwave
door,
remove
the
two
upper
screws
in
the
trim
kit
holding
the top
mounting
bracket
(see
figure
1
next
page)
and
set
the
bracket
and
screws
to
the
side.
b.
Using
scissors
cut
along
the
cut
line
on
the
template
(provided).
c.
Find
the
center
of
the
cabinet
cutout.
d.
Align
the
template
"center
of
opening”
to
the
center
of
the
cabinet
cutout
making
sure
the top
of
the
cabinet
cutout
corresponds
with
the
template
"top
of
opening”
indicator
line.
Tape
may
be
used
to
hold
the
template
temporarily
in
place.
e.
Locate
and
mark
screw
holes
(A)
at
both
ends,
2
each
side,
of
template.
f.
Remove
template
and
set
it
to
the
side.
g.
Drill
pilot
holes
into
cabinet
using
7/64’
or
#35
drill
bit.
h.
Install
top
mount
bracket
(from
step
3a)
to
cabinet
with
the
provided
wood
screws.
(1/2”
X
4)
CAUTION
For
European
style
cabinets
(flush
front)
the
required
clearance
for
operation
of
the
oven
door
is
minimum
spacing
of
7/8”
between
the
cutout
and
the
door,
hinge
or
drawer
of
the
cabinet.
Some
built-in
cabinets
may
not
be
wide
enough,
due
to
their
construction,
to
allow
this
installation.
Top
bracket
mounting
installation
instructions:
(continued)
i.
Install
and
push
unit
in
until
trim
frame
engages
with
top
mount
bracket.
j.
Drive
two
screws
that
were
removed
in
step
(a)
Do
not
over
tighten
the
screws.
4.
Attach
unit
to
the
cabinet
with
4
No.
8,
flat
head
screws
supplied
inside
of
envelope
containing
these
instructions.
Pre-drill
holes
in
cabinet
for
attachment
screws
using
1/8,
drill.
Oven
mounting
holes
are
provided
in
side
trim.
5.
See
instructions
’Electrical
Connections”
for
electrical
hook-up.
6.
See
figure
2
next
page
for
lower
trim
installation.
7.
See
User’s
Manual
for
operating
instructions.
8101P744-60
(11-06-00)