Installation Instructions Model: Polaris General Description: Subwoofer Install Part Number: MBQG-SUB-1 Assembly Time: 90 Min (1.5-Hours) Before you begin, read through these instructions and check that all parts are present. Always disconnect negative battery terminal prior to installation. Please note that MB Quart cannot assume any responsibility for damage resulting from incorrect installation. Parts ListParts List No.
Dash Disassembly ● Remove hood by turning two latches ● Remove seven push clips from front of dash Page 2 of 19
Dash Disassembly ● Remove top two push pins from driver and passenger door opening ● Lift front of dash at eight locations with Bojo tool Page 3 of 19
Dash Disassembly ● Remove if your machine has upper pocket ● Remove lower switch locations (If your vehicle has switches installed note connections and disconnect) ● Disconnect wires from back of 12 volt accessory port Page 4 of 19
Dash Disassembly ● Remove plastic nut from ignition switch and remove from dash ● Lower the steering column and disconnect wiring from the back of the instrument cluster and emove the two 10mm bolts to remove the instrument cluster ● Disconnect the connectors from the back of the light and four wheel drive switches Page 5 of 19
Dash Disassembly ● Remove two T40 bolts from the instrument cluster pocket ● Remove two T40 bolts in front of the shift knob ● Remove two T40 bolts from inside the glove box Page 6 of 19
Dash Disassembly ● Carefully pull dash toward rear of vehicle by door opening on driver and passenger sides ● Carefully remove dash from vehicle by lifting up and out of the vehicle ● Remove seats from vehicle Page 7 of 19
Dash Disassembly ● If your General is a 4-seat version continue, if you have a 2-seat skip ahead.
Dash Disassembly ● Remove (4) 13mm bolts and the grab handle ● Remove six push pins and three T40 bolts ● Remove passenger center console side panel Page 9 of 19
Subwoofer Enclosure Install ● Install amplifier plate using two T40 self cutting screws into the two existing holes circled and you may have to remove a wire clip if present and leave screws loose till another step ● Rotate enclosure toward bracket lifting upward and using a 4mm allen wrench loosely install the three M5 button head bolts with thread patch to the top of the enclosure ● Rotate enclosure toward bracket lifting upward and using a 4mm allen wrench, loosely install the three M5 button head bolt
Subwoofer Enclosure Install ● Tighten three M5 bolts on top of enclosure with a 4mm allen wrench and also tighten two T40 Torx bolts and three Phillips self tapping screws on the front of the plate Page 11 of 19
Reassembly ● Install front passenger center console, carefully sliding into place around subwoofer enclosure ● Install six push pins NOTE The two up high by firewall will need to be inserted from drivers side by steering wheel.
Reassembly ● Install passenger grab handle with four 13mm bolts ● Install center cover with two push pins ● If two-seat skip ahead if four-seat, then install rear console and install six push pins on driver and passenger side Page 13 of 19
Reassembly ● Install rear glove box in rear center console (Remember to connect wires to bottom 12-volt accessory port) ● Install two push pins under glove box lid ● Re-install the dash in the vehicle Page 14 of 19
Reassembly ● Install key switch and align to detent ● Install two T40 bolts on driver side instrument cluster area ● Install two T40 bolts in center console Page 15 of 19
Reassembly ● Install two T40 bolts in passenger glove box ● Install instrument cluster with two 10mm bolts ● Connect instrument cluster connector Page 16 of 19
Reassembly ● Install top of dash, snapping eight push clips on front of dash ● Install six push pins on front of dash Page 17 of 19
Reassembly ● Install hood Page 18 of 19
FCC Notice This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a mobile installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
