Quick Start Installation Guide NA2-400.2 NA2-320.4 NA2-400.1 NA2-500.5 &RQJUDWXODWLRQV RQ \RXU FKRLFH RI D 0%4XDUW DPSOL¿HU This “Quick Start Installation” guide is meant to help you “hook up” and play music. For more detailed information, RQ V\VWHP VHWWLQJ VSHDNHU DQG VXEZRRIHU FRQ¿JXUDWLRQ DQG IXOO VSHFL¿FDWLRQV E\ PRGHO YLVLW WKH ZHEVLWH http://mbquart.com/manuals.
Before you start CAUTION Many new and factory radios require a reset code when disconnected from battery power. This is an anti-theft feature. Before unplugging power, you must determine if your radio/source unit requires a reset code. Check the operation manual for your vehicle or contact the dealer. Power cable size and fusing It is critical to use the proper power and ground cable. Select the size OLVWHG KHUH IRU \RXU DPSOL¿HU PRGHO Always use high quality copper cable.
4 Chassis Ground The chassis ground connection is critical to the performance RI WKH DPSOL¿HU &KRRVH D location that is close to the DPSOL¿HU &RPSOHWHO\ VFUDSH away the paint and use a nut and bolt if possible. DO NOT USE AN EXISTING FACTORY BOLT! 5 Power Connection Bare metal Attach the chassis ground, +12V and remote wire. It is important to make sure these connections are very secure.
8 Speaker Connect the speaker cables to the speaker output connectors. Follow the diagram below WKDW EHVW ¿WV \RXU VSHDNHU FRQ¿JXUDWLRQ Connections NA2-400.1 / NA2-500.5 Speaker Positive - Gray Speaker Negative - Gray / Black NA2-400.2 Left Positive - White Left Negative - White / Black Right Positive - Gray Right Negative - Gray / Black NA2-320.4 / NA2-500.
Setup A The illustrations below describe the various controls. Refer to WKH LOOXVWUDWLRQ WKDW PDWFKHV \RXU DPSOL¿HU Settings NA2-400.1 5 BOOST L 1 GAIN Adjustment 1 4 The Subsonic Filter will cut off the frequencies below the setting. If using with a subwoofer the settin should be kept between 15-25Hz. L 4 3 2 HP OFF LP INPUT LEVEL HP LP R 9V 0.2V 1 15Hz 300Hz 50Hz 300Hz 3 3 NA2-320.
C Remote Level Control Some models include a bass remote. Avoid adjusting the bass remote while operating vehicle. The information contained within this document is intended to offer some basic guidelines for a few of the most common installations. More complex audio systems should be installed by a competent professional. Additional installation information available at www.maxxsonics.com WARRANTY Maxxsonics USA Inc.
Assembly Instructions Model: Jeep JL (Wrangler) & JT (Gladiator) Description: Subwoofer Install Part Number: MBQJ-SUBA-1 & MBQJ-SUB-1 Assembly Time: 120 Minutes (2 Hours) Before you beign, read thought these instructions and check that all parts are present. Please note that MB Quart cannot assume any responsibility for damage resulting from incorrect installation. MBQJ-SUB-1 Parts List No.
Disassembly ● Remove (4)10mm bolts securing the under seat storage compartment May need to remove rubber insert to gain access to bolts ● Remove jack Page 2 of 5
Subwoofer Installation ● Cut a small hole in the carpet (as pictured) to pass the subwoofer extension harness through going toward the outside of vehicle along door seal toward the passenger seat area. ● Install jack ● Connect subwoofer enclosure wiring to subwoofer extension harness.
Subwoofer Installation ● Reusing the (4) 10 mm bolts holding the storage compartment, secure the subwoofer enclosure ● Connect the subwoofer speaker wires to the subwoofer and repeat the process for other subwoofer ● Secure the subwoofer to the enclosure with (8) High-Low screws using a T-20 Torx bit Page 4 of 5
FCC Notification This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a mobile installation. This equipment generates uses and can radiate radio frequency energy. If not installed and used in accordance with the instructions, this equipment may cause harmful interference to radio communications.
