Installation Manual MBQX-POD-1 CAN-AM MAVERICK X3 400 WATT / TWO SPEAKER UTV-TUNED AUDIO PACKAGE
INTRODUCTION Thanks for choosing MB QUART! The UTV-Tuned 2-speaker, 400 watt system for applicable Can-Am Maverick X3 vehicles (2017 and up) is engineered for your vehicle. The installation process is simple and straightforward. Installation following these detailed instructions can be completed in about 2 hours. INSTALLATION OVERVIEW VIDEO Many of our vehicle-specific products feature a “how to” install video with additional details on making your installation successful.
INSTALLATION TIME About 2 hours are required to complete this installation (assuming unmodified vehicle). Add installation time for your own source unit, choice in power wiring and any additional speakers, subwoofer(s) and amplifiers.
DISASSEMBLY VEHICLE DISASSEMBLY This section covers console and dash component removal. REMOVE CONSOLE SIDES 1 Remove driver’s side console side panel using a pry tool from the top to gently release the pressure-fit clips. 2 3 Remove passenger’s side console side panel using a pry tool from the top to gently release the pressure-fit clips. Remove front of center console side panel on passenger’s side (footwell area) using a pry tool to gently release the pressurefit clips.
VEHICLE DISASSEMBLY This section covers left and right side top dash speaker panels and gauge cluster removal. REMOVE PASSENGER & DRIVER TOP DASH PANELS 1 Remove gas filler access door on passenger side. Note above the grommet for the retainer clip, there is a 10mm nut attaching a mounting screw. 2 3 Remove three T-30 screws from the top edge of the passenger’s side dash where the hood line meets the dash as indicated. Remove the remaining two T-30 screws on the side edge of the panel.
DISASSEMBLY & PREP VEHICLE DISASSEMBLY Removal of the center console inner cover facilitates routing wiring from the recommended bus bar location into the dash area where the amplifier and source unit are likely to be installed INNER COVER OF CENTER CONSOLE 1 Driver’s Side View Prepare to remove forward inner cover of the center console. Note - some modified vehicles may have aftermarket console electronics present. 2 3 Remove two T-30 screws on the lower front of center console.
CONNECT AND ROUTE WIRING This section covers the recommendation of connecting your power, ground and ignition/accessory wiring to the bus bar in the passenger side center console and routing that wiring to the dash area. Battery +12V Ignition +12V 1 3 2 Identify bus bar in passenger side center console. Top is chassis ground, middle is constant +12v power (battery) and bottom is +12v ignition. Connect your Ground, Battery and Ignition wires to the bus bar locations.
AMPLIFIER INSTALLATION AMPLIFIER INSTALLATION This section covers general wiring and the installation the NA2-400.2 amplifier using the optional MBQXSUB-ACC-1 mounting plate. If not using this mounting plate, you’ll need to determine your own mounting location. Source Unit “FRONT OUTPUTS” To Amplifier Location 1 4-Pin Speaker Plug Route speaker wiring from each front speaker location to the amplifier’s installation location. Connect wires to 4-pin speaker plug as shown.
FRONT SPEAKER INSTALLATION Identify Two Clip Retainers 1 Locate the factory front left and right speaker panels and identify two mounting clip retainers and washers that need to be removed on each. 4 Connect passenger side speaker to your installed speaker wire. Crimp connectors are needed to mate with speaker terminals. Gently Compress to Remove 2 From bottom side, gently remove mounting clip retainers as indicated. This can be done with your fingers. Do this for both passenger and driver side.
FRONT SPEAKERS FRONT SPEAKER INSTALLATION (Continued) This section continues front speaker installation focusing on the driver’s side. Final driver’s side panel installation will occur AFTER the audio system initial testing is validated and complete. 8mm Screws Depress Tabs 1 Remove switches on lower left of original driver’s side dash panel by depressing the tabs on the top and bottom of the back of switch.
AMPLIFIER SETTINGS The chart below provides general crossover filter and bass boost switch settings depending on the Can-Am X3 UTV-Tuned Audio package you have. TUNED PACKAGE MBQX-POD-1 TWO-CHANNEL AMPLIFIER HP-OFF-LP/BP Switch to – High Pass (80Hz) MONO AMPLIFIER N/A ADJUST NA2-400.2 TWO-CHANNEL AMPLIFIER Make the following initial adjustments to the NA2-400.2 shown at right: ● X-OVER - Switch to “HP” position. This designates the amplifier’s crossover filter for “high pass” functionality.
INITIAL TESTING INITIAL TESTING Confirm that everything is working as intended before final tuning, fitting and reassembly. STEP 1 – RECONNECT THE BATTERY First, ensure the battery is fully charged. Using a 10mm socket, then reconnect the negative terminal of the negative battery cable as indicated. STEP 2 – CONNECT SOURCE UNIT Make any final connections to your chosen source unit so that it can power up and output a music source for testing.
FINE TUNING NOTE – Gain control, it is important to adjust each amplifier gain as described in the manual. Remember, these settings are NOT volume controls. Gain controls, properly adjusted help properly balance the system sound between lows, highs and minimize distortion that comes from the source unit. Listen for a clear, crisp audio sound. The ideal gain setting should allow full volume from the source unit without audible distortion. A The illustrations below describe the various controls.
REASSEMBLY VEHICLE REASSEMBLY As you begin reassembly, take the time to ensure no fastener, screw or clip is excluded. Review any prior disassembly steps to ensure you don’t miss any hardware during reassembly. *AFTERMARKET ROLL CAGES Although MB Quart front speakers come pre-installed in the Can-Am replacement panels, they may require removal from the panel to fit low-slung aftermarket roll cages that fit close to the hood area.
FINAL INSPECTION Here is a check list to make sure your vehicle is ready to hit the trails. You should pull & tighten everything so that you know your Can-Am X3 and your audio equipment are secure.
WIRING LAYOUT COMPLETE CAN-AM X3 SYSTEM LAYOUT BUS BAR (CENTER CONSOLE) This diagram shows all optional MB Quart equipment available for the Can-Am X3.
NOTES Use this section to record serial numbers of each product, final gain and crossover settings of amplifiers or any other wiring or installation-related details that will be helpful if you need to add on to the system or troubleshoot any unforeseen issues.
FCC Notice This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a mobile installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
Quick Start Installation Guide NA2-400.2 NA2-320.4 NA2-400.1 NA2-500.5 &RQJUDWXODWLRQV RQ \RXU FKRLFH RI D 0%4XDUW DPSOL¿HU This “Quick Start Installation” guide is meant to help you “hook up” and play music. For more detailed information, RQ V\VWHP VHWWLQJ VSHDNHU DQG VXEZRRIHU FRQ¿JXUDWLRQ DQG IXOO VSHFL¿FDWLRQV E\ PRGHO YLVLW WKH ZHEVLWH http://mbquart.com/manuals.
Before you start CAUTION Many new and factory radios require a reset code when disconnected from battery power. This is an anti-theft feature. Before unplugging power, you must determine if your radio/source unit requires a reset code. Check the operation manual for your vehicle or contact the dealer. Power cable size and fusing It is critical to use the proper power and ground cable. Select the size OLVWHG KHUH IRU \RXU DPSOL¿HU PRGHO Always use high quality copper cable.
4 Chassis Ground The chassis ground connection is critical to the performance RI WKH DPSOL¿HU &KRRVH D location that is close to the DPSOL¿HU &RPSOHWHO\ VFUDSH away the paint and use a nut and bolt if possible. DO NOT USE AN EXISTING FACTORY BOLT! 5 Power Connection Bare metal Attach the chassis ground, +12V and remote wire. It is important to make sure these connections are very secure.
8 Speaker Connect the speaker cables to the speaker output connectors. Follow the diagram below WKDW EHVW ¿WV \RXU VSHDNHU FRQ¿JXUDWLRQ Connections NA2-400.1 / NA2-500.5 Speaker Positive - Gray Speaker Negative - Gray / Black NA2-400.2 Left Positive - White Left Negative - White / Black Right Positive - Gray Right Negative - Gray / Black NA2-320.4 / NA2-500.
Setup A The illustrations below describe the various controls. Refer to WKH LOOXVWUDWLRQ WKDW PDWFKHV \RXU DPSOL¿HU Settings NA2-400.1 5 BOOST L 1 GAIN Adjustment 0dB INPUT LEVEL 9V 0.2V 1 L 4 3 2 HP OFF LP INPUT LEVEL HP LP R 9V 0.2V 3 Frequencies Adjustment 1 15Hz 300Hz 50Hz 300Hz 3 3 NA2-320.4 2 FRONT X-OVER INPUT L L FRONT REAR R R HP REAR X-OVER HP OFF LEVEL 9V OFF LEVEL 0.2V 9V 0.2V 1 NA2-500.
C Remote Level Control Some models include a bass remote. Avoid adjusting the bass remote while operating vehicle. The information contained within this document is intended to offer some basic guidelines for a few of the most common installations. More complex audio systems should be installed by a competent professional. Additional installation information available at www.maxxsonics.com WARRANTY Maxxsonics USA Inc.