Installation Manual MBQX-SUB-2 CAN-AM MAVERICK X3 ADD-ON 10” SUBWOOFER / 400 WATT UTV-TUNED AUDIO PACKAGE
INTRODUCTION Thanks for choosing MB QUART! The UTV-Tuned Add-On 10” Subwoofer with 400 Watt Amplifier for applicable Can-Am Maverick X3 vehicles (2017 and up) is engineered for your vehicle. Installation following these instructions can be completed in about 2 hours when you have a Stage 2, 3 or 5 MB Quart system for Can-Am X3 already installed. INSTALLATION OVERVIEW VIDEO Many of our vehicle-specific products feature a “how to” install video with additional details on making your installation successful.
INSTALLATION TIME About 2 hours are required to complete this installation if you’ve already got a Stage 2, 3 or 5 MB Quart Can-Am UTV-tuned sytem installed.
DISASSEMBLY VEHICLE DISASSEMBLY Console side and lower center dash removal (steps 1-3) aren’t necessary if you’ve already installed the subwoofer wiring harness(es) per instructions from the Stage kit. Source unit requires removal. REMOVE CONSOLE SIDES 1 Remove driver’s side console side panel using a pry tool from the top to gently release the pressure-fit clips. 2 3 Remove passenger’s side console side panel using a pry tool from the top to gently release the pressure-fit clips.
VEHICLE DISASSEMBLY This section covers left and right side top dash speaker panels and gauge cluster removal. Passenger side panel removal (Steps 1-4) are not required for the subwoofer system installation Steps 5-9 are required. 10mm nut on back side 1 Remove gas filler access door on passenger side. Note above the grommet for the retainer clip, there is a 10mm nut attaching a mounting screw.
SUBWOOFER MOUNTING MAIN SUBWOOFER INSTALLATION (SUB 1) This section covers the installation of the primary subwoofer. MB Quart recommends this is installed under the driver’s seat, although it can fit under either front seat. Logo 1 RIGHT LEFT Identify front enclosure brackets. Orientation is referenced to the logo. Left and right are stamped “L” and “R” on the bracket and enclosure. 2 3 Remove the factory-supplied aluminum spacers from rear bolts of seat mounts*.
SUBWOOFER AMPLIFIER INSTALLATION FOR STAGE 2 SYSTEMS This section covers the installation of the 400.1 subwoofer amplifier included in MBQX-SUB-2 in a Stage 2 system using the dual amp plate shown that should already be installed. If already installed, amp plate first requires removal to complete this step. Review amplifier settings on page 11 of this manual. 400.2 400.2 400.1 400.1 1 Attach amplifiers* to mounting plate with included hardware as indicated. Use only three nuts/ bolts on 400.
AMPLIFIER MOUNTING SUBWOOFER AMPLIFIER INSTALLATION FOR STAGE 3 and 5 SYSTEMS This section covers the installation of the 400.1 subwoofer amplifier included in MBQX-SUB-2 in a Stage 3 or 5 system using the MBQX-SUB-ACC-1 accessory amp plate shown. Review amplifier settings on page 11 of this manual and esure both subwoofer amplifier settings are matched as close as possible. No Nut/ Bolt Here 1 MBQX-SUB-ACC-1 Begin by identifying the amplifier mounting plate and hardware.
ADD-ON SUBWOOFER INSTALLATION FOR STAGE 3 and 5 SYSTEMS Logo 1 RIGHT LEFT Identify front enclosure brackets. Orientation is referenced to the logo. Left and right are stamped “L” and “R” on the bracket and enclosure. 2 3 Remove the factory-supplied aluminum spacers from rear bolts of seat mounts*. Replace with supplied MB Quart spacers for bracket tolerance.
FRONT SPEAKERS FRONT SPEAKER INSTALLATION This section covers temporary installation of the driver’s side speaker panel. Final installation of the speaker panel occurs after the system is tested and gone through a thorough inspection prior to reassembly. 8mm Screws 1 If the vehicle has the SmartLok differential control module, re-attach to the underside of the new dash panel with the original four 8mm screws.
AMPLIFIER SETTINGS TUNED PACKAGE MBQX-STG5-1 MBQX-STG3-1 MBQX-STG2-RAD-1 MBQX-STG2-1 MBQX-SUB-2 TWO-CHANNEL AMPLIFIER HP-OFF-LP/BP Switch to HP - High Pass (80Hz) HP-OFF-LP/BP Switch to HP - High Pass (80Hz) HP-OFF-LP/BP Switch to – High Pass (80Hz) HP-OFF-LP/BP Switch to – High Pass (80Hz) N/A MONO AMPLIFIER Bass Boost to 0dB LPF at 100Hz Bass Boost to 0dB LPF at 100Hz N/A N/A Bass Boost to 0dB LPF at 100Hz This manual assumes the full Stage 5 System and provides the information for initial settings ac
INITIAL TESTING INITIAL TESTING Confirm that everything is working as intended before final tuning, fitting and reassembly. Since you’ve already had a Stage 2, 3 or 5 system previously installed, this initial testing is simply addressing the amplifer and subwoofer added in this installation manual procedure. STEP 1 – RECONNECT THE BATTERY First, ensure the battery is fully charged. Using a 10mm socket, then reconnect the negative terminal of the negative battery cable as indicated.
FINE TUNING NOTE – Gain control, it is important to adjust each amplifier gain as described in the manual. Remember, these settings are NOT volume controls. Gain controls, properly adjusted help properly balance the system sound between lows, highs and minimize distortion that comes from the source unit. Listen for a clear, crisp audio sound. The ideal gain setting should allow full volume from the source unit without audible distortion. A The illustrations below describe the various controls.
REASSEMBLY VEHICLE REASSEMBLY As you begin reassembly, take the time to ensure no fastener, screw or clip is excluded. Review any prior disassembly steps to ensure you don’t miss any hardware during reassembly. *AFTERMARKET ROLL CAGES Although MB Quart front speakers come pre-installed in the Can-Am replacement panels, they may require removal from the panel to fit low-slung aftermarket roll cages that fit close to the hood area.
FINAL INSPECTION Here is a check list to make sure your vehicle is ready to hit the trails. You should pull & tighten everything so that you know your Can-Am X3 and your audio equipment are secure.
WIRING LAYOUT COMPLETE WIRING LAYOUT BUS BAR (CENTER CONSOLE) This is a complete wiring harness layout diagram, including optional equipment.
NOTES Use this section to record serial numbers of each product, final gain and crossover settings of amplifiers or any other wiring or installation-related details that will be helpful if you need to add on to the system or troubleshoot any unforeseen issues.
FCC Notice This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a mobile installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
