AMPLIFIERS ODIN 2K & CYCLOPS 3K P roducts Manual MT OLYMPUS
A. GENERAL INSTALLATION PROCEDURE The MT OLYMPUS Series products have been designed to a very high level of performance, with features unavailable in any other product. All of the amplifiers have variable crossovers built in, with added touches such as subsonic filter, parametric bass equalization and a remote control module that allows the overall Level of bass boost to be controlled from the driver’s seat.
4 INSTALLATION TIP: Use the same approach when installing head units, equalizers or any audio equipment for that WIRE LENGTH Power & ground connections: (see the features matrix on page 5 for proper gauge cables per amplifier) Run the wiring so that RCA cables are at least 18“ away from power and speaker cables. Keep RCA cables away from electrical devices in the vehicle that can cause electrical noise, such as electric fuel pumps, emission control modules and other on-board electronic modules.
FEATURES FOR ODIN 2K & CYCLOPS 3K 6 7 MT. OLYMPUS AMPLIFIERS INPUT LEVEL OUTPUT L 9V R Mt. Olympus is a unique series of amplifiers regarding channel stability and design. PHASE BOOST WIDTH CENTER REMOTE SUBSONIC MODE LPF MASTER OUT DIAGNOSTIC AMBER-THERMAL RED-SHORT CIRCUIT L 0.2V 0 180 0 10dB 30 100Hz 15 35Hz 35 250Hz MST PROTECT SLV RED-CLIP AMBER-NEAR CLIP GREEN-PRE CLIP BASS EQ R POWER SLAVE IN Designed and Engineered in the U.S.A.
9 ODIN 2K, CYCLOPS 3K C . OD IN 2K & C Y C L OP S 3 K Amp l i fi e r Ap p l ic ations INPUT Interconnect cable checklist: LEVEL OUTPUT L 9V A MONO signal source is suggested, such as would be available from the mono – sub bass output of an active crossover, whether stand alone, or built into a head unit or equalizer. BOOST PHASE WIDTH CENTER REMOTE SUBSONIC MODE LPF MASTER OUT R 0.
10 DUAL AMP INSTALLATION PROCEDURE Connect the amp LINE INPUTS to the Radio/CD player full range or mono line outputs with good quality RCA interconnect cables. »» Plug in the HFR-G1 bass remote module into the amp remote input DIN connection on the Master amp. This will allow the Master amp to control both Master and Slave with just one Bass Remote. »» Connect an RCA jumper cable from the Master amp MASTER OUTPUT to the Slave amp SLAVE INPUT. INPUT LEVEL OUTPUT L L R R 9V 0.
12 Bandwidth: This setting controls the amount of frequencies included in the Bass Boost. The bandwidth varies from narrow to wide in a pyramid style boost with the selected Bass Frequency value being the center. Boost: ODIN 2K & CYCLOPS 3K General: At this point you are ready to get more specific on the settings for the amplifier. Phase: Time alignment, typically recommended at 0 degrees unless using multiple amps and subs in both the front and rear of the vehicle.
Low output power 14 Check that level controls have been set up properly. 2. Make sure that the battery voltage, as measured at the amplifier’s +12 volt and ground terminals, is 12.6 volts or more. The key to finding the problem in a misbehaving sound system is to isolate parts of that system in a logical fashion to track down the fault. 3. Check all +12 volt and ground connections. Description of the Diagnostic system built into all HIFONICS amplifiers Fuses blowing E.
16 A ticking or whine that changes with engine RPM: 1. This problem could be caused by radiation pickup of RCA cables too near to a fuel pump or a distributor, for instance. Relocate cables to resolve this issue. 3. Check that the head unit ground is connected straight to the vehicle chassis, and does not use factory wiring for ground. Try to supply the head unit with a clean +12 volt supply directly from the battery +, instead of using a supply from the in-dash wiring/fusebox.
18 HFXR - Hifonics Electronic Crossover The HFEQ is the perfect addition to any system. The HFEQ is a ½ DIN ISO mount chassis which means it needs a very narrow hole to be trimmed into the dash. It can also be mounted under the dash or center console. The key to successful operation is “within reach” for quick adjustments to the system when music style or sound changes.
20 21 ODIN 2K RMS/DYNAMIC CYCLOPS 3K RMS/DYNAMIC 4-Ohms 450/900 600/1200 2-Ohms 800/1600 1100/2200 1-Ohm 1000/2000 1500/3000 Mono Bridged @ 4-Ohms n/a n/a Mono Bridged @ 2-Ohms n/a n/a PWM PWM MOSFET MOSFET Yes Yes ODIN 2K CYCLOPS 3K 15Hz-250Hz 15Hz-250Hz >200 >200 >96dB >96dB <0.1 <0.1 0.2V-9.0V 0.2V-9.
22 23
Maxxsonics® USA Inc. maxxsonics.com 1290 Ensell Road Lake Zurich Illinois 60047 USA Phone: 847-540-7700 FAXX: 847-540-9776 ©2014 Maxxsonics USA, Inc. All Rights Reserved Specifications And Designs Are Subject To Change Without Notice.