MT OLYMPUS AMPLIFIERS BOLTAR 2K / COLOSSUS PRO 5K COLOSSUS 6.5K / JUPITER 1.
HIFONICS MT OLYMPUS HIGH PERFORMANCE AMPLIFIERS The MT OLYMPUS Series products have been designed to a very high level of performance, with features unavailable in any other product. All of the amplifiers have variable crossovers built in, with added touches such as subsonic filter, parametric bass equalization and a remote control module that allows overall Level control from reach of the drivers seat.
GENERAL INSTALLATION PROCEDURE System Design The success of any car stereo system relies on several factors, such as the system design, execution of the installation, and system setup. Please remember that any system is only as good as its weakest link. Please remember that higher power systems are not necessarily useful purely for high sound pressure levels, but also to establish a headroom capability, to reproduce musical peaks cleanly without distortion.
AMPLIFIER FEATURE DESCRIPTIONS MT OLYMPUS AMPLIFIERS: This is a unique series of amplifiers regarding channel stability and design. The COLOSSUS and COLOSSUS PRO are stable at 4/2/1-Ohm per channel and 4/2-Ohms bridged. The BOLTAR and JUPITER are stable at 4/2-Ohms per channel and 4-Ohms bridged. The HERCULES and ATLAS is stable at 4/2/1-Ohm. The input sensitivities for rated output powers are variable from 0.2V to 9V. All crossovers are fully variable in their respective ranges.
BOLTAR / COLOSSUS PRO 2-CHANNEL AMPLIFIER APPLICATIONS FULL RANGE STEREO NOTE: Minimum final loudspeaker impedances: BOLTAR: 4/2 Ohm stereo mode or 4 Ohms mono mode COLOSSUS PRO: 4/2/1 Ohm stereo mode or 4/2 Ohms mono mode FULL RANGE HP LP/BP RED-CLIP AMBER-NEAR CLIP GREEN-PRE CLIP DIAGNOSTIC RED-SHORT CIRCUIT AMBER-THERMAL LP/BP STEREO 12dB/OCT MONO 24dB/OCT LP DIRECT HFR-G1 REMOTE SPEAKER OUTPUT BRIDGED + RIGHT + LEFT - 1.
JUPITER 4-CHANNEL AMPLIFIER APPLICATIONS 4 CHANNEL FULL RANGE SYSTEM Here we show how to use the 4 channel amplifiers as straightforward discrete 4 channel full range units. - HI PASS: N/A - LOW PASS: N/A Interconnect cable checklist: - Connect the four inputs of the amplifier to a Radio/CD with quality RCA cables.
MULTI-AMPLIFIER APPLICATIONS Front/Rear high pass, using a 2 channel amplifier for mono sub bass The combination of a BOLTAR or COLOSSUS PRO and a JUPITER amplifier, utilizing their built in crossovers, makes it a snap to put together a full system with front and rear highs, with mono sub bass. Interconnect cable checklist: - Using good quality RCA cables, feed the front and rear outputs of a head unit to the inputs of the 4 channel JUPITER as shown.
HERCULES / ATLAS MONO AMPLIFIER APPLICATIONS Basic application SINGLE AMP INSTALLATION PROCEDURE: 1. Connect the amp LINE INPUTS to the Radio/CD player full range or mono line out puts with good quality RCA interconnect cables. 2. Plug the HFR-G1 remote module into the amp remote input DIN connection. 3. Route a 0 gauge power cables directly to the vehicle battery with an in-line fuse. 4. Connect a 0 gauge ground cables directly to chassis ground with in 36” of the amp.
COLOSSUS DUAL MONO AMPLIFIER APPLICATIONS BASIC APPLICATION The Colossus Dual Mono Block amplifiers are capable of 4, 2 & 1 Ohm stereo and 4 & 2 bridged loads. SINGLE AMP INSTALLATION PROCEDURE: 1. Connect the amp LINE INPUTS to the Radio/CD player full range or mono line out puts with good quality RCA interconnect cables. 2. Plug in the HFR-G1 bass remote module into the amp REMOTE INPUT jack. 3. Route a 0 gauge power cable directly to the vehicle battery with an in-line 300 amp fuse.
SETTING UP SYSTEMS AFTER INSTALLATION FOR BEST PERFORMANCE BOLTAR / COLOSSUS PRO / JUPITER General: At this point you are ready to get more specific on the settings for your amplifier. X-OVER: -When in HP operation, this setting acts as a low frequency cut off for your system reproduction. The point that you set your FILTER FREQUENCY at cuts off all frequencies from reproduction below this point.
TROUBLESHOOTING A SYSTEM The key to finding the problem in a misbehaving sound system is to isolate parts of that system in a logical fashion to track down the fault. Description of the Diagnostic system built into all HIFONICS amplifiers The diagnostic system will shut down the amplifier, until reset by turning the head unit off, and back on. This state of affairs will be indicated by the front panel PROTECT LED lighting up under the following conditions: 1 - A sort circuit on the loudspeaker leads.
10
Maxxsonics Limited Warranty As the manufacturer of Maxxsonics, MB Quart, Autotek, Crunch and Hifonics car audio products, Maxxsonics USA Inc. Warrants to the original consumer purchaser the amplifier to be free from defects in material and workmanship for one (1) Year from date of purchase. All other parts and accessories of the system are warrantied to be free from defects in material and workmanship for one (1) year from date of purchase.
Accessories HDBR DIGITAL BASS RESTORATION RCA INPUT FREQUENCY RANGE CENTER FREQUENCY OUTPUT LEVEL 4.5V 2.5V 7V BALANCED GROUND ISOLATION UNBALANCED GROUND WIDE 9V NARROW .2V 200-Ohms ISOLATED POWER FROM GODS THE The HDBR contains a BASS DRIVER circuit that accurately recreates and injects Low Frequency information back into the signal path. What that means in everyday terms is that the HDBR will give more bass impact to your best compact discs or your lowest quality recordings.
13
Biggest POWER systems V3 Products, Level 10 Performance + 1 Year Warranty Moderate POWER systems V2 Products, Level 7 Performance + 6 Month Warranty Smaller POWER systems V1 Products, Level 5 Performance 14
PART#: A213