Installation manual

NA710.5
7
5 Channel Discrete Operation:
MODE: “5” since 3 sets of RCA’s are connected.
You can use this configuration simply as 4 discrete full range channels, with a 5th low
pass channel. All of the crossovers are bypassed , except the LOW PASS on channel 5.
Control checklist:
- Refer to the section “Settings for Best Performance”
Interconnect cable checklist:
Connect channel 1&2 inputs to the front output, channels 3&4 to the rear output, and
Minimum final loudspeaker impedances:
channel 5 to the mono subwoofer output of a head unit or in dash equalizer.
- 2 Ohms per channel for channels 1-4
- 2 Ohms on channel 5
Switch setting checklist:
- CH 1 / 2 X-OVER: FULL
- CH 3 / 4 X-OVER: FULL
Single Set of Stereo RCA’s
MODE: “2” since 1 set of RCA’s are connected.
We will use the same basic setup on the speaker and subwoofer connections as above
to illustrate an installation that only has 1 set of stereo RCA’s to connect to this amplifier.
Control checklist:
By switching the amplifier to 2CH on the INPUT MODE, you now provide signal to all
- Refer to the section “Settings for Best Performance”
channels on the amplifier. You sacrifice the ability to fade front to rear though.
Minimum final loudspeaker impedances:
Interconnect cable checklist:
- 2 Ohms per channel for channels 1-4
Connect Stereo Left and Right RCA’s from headunit to CH1&2 RCA Inputs.
- 1 Ohm on channel 5
Switch setting checklist:
- CH 1 / 2 X-OVER: FULL
- CH 3 / 4 X-OVER: FULL
5-Channel Amplifiers
FEATURES:
- 3 Sets of RCA inputs
- LEVEL: Variable sensitivity from 0.2V to 6V
- BASS BOOST: Adjustable 45Hz bass boost from 0dB to 10dB
- X-OVER: Selects internal crossover functions
- FULL: Bypasses all crossovers for full frequency operation
- BP: Selects the built in LOW PASS filter
- HP: Selects the built in HI PASS filter
- POWER LED: Indicates the powered up and turned on condition
- PROTECTION LED: Indicates a high voltage, low voltage, short circuit,
hard clip, over heating or DC fault condition.
- MODE: “2” indicates one set of RCA’s are being used. This will also pass signal to channels 3/4 and 5 through
1/2 inputs. “4” indicates connecting 2 sets of RCA’s to 1/2 and 3/4 inputs. “5” indicates connecting 3 sets of
RCA’s to channels 1/2, 3/4 and mono signal to channel 5 inputs.
POWER INPUT
POWER INPUT
GND REM BATT+12V
GND REM BATT+12V
1CH 2CH
1CH 2CH
3CH 4CH 5CH
3CH 4CH 5CH
+ - + - + - + - + -
+ - + - + - + - + -
BRIDGED
BRIDGED
BRIDGED
BRIDGED
50Hz 4Khz
HI PASS LEVEL HI PASS LOW PASS LEVEL
REMOTE LOW PASS BASS BOOST LEVEL Ch5 MODE
HP FULL HP FULL BP
X-OVER
Ch1 / Ch2
X-OVER
Ch3 / Ch4
30Hz 150hz
6V 0.2V
0dB 10dB
6V 0.2V
50Hz 150hz
6V 0.2V
250Hz 4kHz
Ch2 Ch4 Ch5
HI FULL
Ch2 Ch4
Ch1 Ch3
INPUT
PROTECT
POWER
Ch5
50Hz 4Khz
50Hz 4Khz
HI PASS LEVEL HI PASS LOW PASS LEVEL
HI PASS LEVEL HI PASS LOW PASS LEVEL
REMOTE LOW PASS BASS BOOST LEVEL Ch5 MODE
REMOTE LOW PASS BASS BOOST LEVEL Ch5 MODE
HP FULL
HP FULL
HP FULL BP
HP FULL BP
X-OVER
Ch1 / Ch2
X-OVER
Ch1 / Ch2
X-OVER
Ch3 / Ch4
X-OVER
Ch3 / Ch4
30Hz 150hz
30Hz 150hz
6V 0.2V
0dB 10dB
6V 0.2V
0dB 10dB
6V 0.2V
6V 0.2V
50Hz 150hz
6V 0.2V
50Hz 150hz
6V 0.2V
250Hz 4kHz
250Hz 4kHz
Ch2 Ch4 Ch5
Ch2 Ch4 Ch5
HI FULL
HI FULL
Ch1
Ch1
Ch3
Ch3
Ch2
Ch2
Ch4
Ch4
INPUT
INPUT
PROTECT
PROTECT
POWER
POWER
Ch5
Ch5