OPERATOR’S SAFETY AND SERVICE MANUAL AP1400 & GP1800 This manual covers the following serial numbers and higher for each model listed: 1400............................................1230500 1800............................................1800950 VIBRATORY MBW, Inc. MBW (UK) Ltd. 250 Hartford Rd • PO Box 440 Slinger, WI 53086-0440 Phone: (262) 644-5234 Fax: (262) 644-5169 Email: mbw@mbw.com Website: www.mbw.
TABLE OF CONTENTS Safety Information . . . . . . . . . . . . . . . . . . . . . . 1 Service. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Torque Chart . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Safety Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Service Tools . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Safety Decals . . . . . . . . . . . . .
WARNING CALIFORNIA PROPOSITION 65 WARNING Engine exhaust and some of its constituents are known in the state of California to cause cancer, birth defects, and other reproductive harm.
SAFETY INFORMATION Introduction SAFE DRESS: Do not wear loose clothing, rings, wristwatches, etc. near machinery. This Safety Alert Symbol is used to call attention to items or operations which may be dangerous to those operating or working with this equipment. The symbol can be found throughout this manual and on the unit. Please read these warnings and cautions, along with all decals, carefully before attempting to operate the unit.
6(5,(6 237,21$/ 52// &$*( :$7(5 7$1. WARNING CAUTION ? @ J OPERATION OF THIS EQUIPMENT MAY CREATE SPARKS THAT CAN START FIRES AROUND DRY VEGETATION. A SPARK ARRESTER MAY BE REQUIRED. THE OPERATOR SHOULD CONTACT LOCAL FIRE AGENCIES FOR LAWS OR REGULATIONS 19791 RELATING TO FIRE PREVENTION Unit may fall and cause injury or damage if lifted improperly. Use handles on deck and base to lift.
SPECIFICATIONS 1400 SERIES CENTRIGUGAL FORCE 6(5,(6 AP1400 GP1400 GP1800 1925 lbs (873 kg) 1925 lbs (873 kg) 2300 lbs (1043 kg) EXCITER (VPM) 5240 5240 4710 TRAVEL SPEED 85 ft./min. (26 m/min.) 85 ft./min. (26 m/min.) 100 ft./min. (30 m/min.) 10 in. (25 cm) 10 in. (25 cm) 12 in. (30 cm) 14 x 21 in. (36 x 53 cm) 14 x 21 in. (36 x 53 cm) 18 x 21 in.
OPERATION Introduction • FUEL FILTER - If clogged or damaged, replace. MBW equipment is intended for use in very severe applications. They are powered by four cycle engines and are available in different sizes and a selection of engines. This parts manual contains only standard parts. Variations of these parts as well as other special parts are not included. Contact your local MBW distributor for assistance in identifying parts not included in this manual.
LIFTING/TRANSPORTING WARNING 1. The unit can be lifted by the handles in front and back of the unit as shown in figure 2. 2. The unit must be transported in the upright position. DO NOT lay machine on its side or top. 3. Secure or tie down unit using the lifting handles . Adding fuel. Leaving the equipment unattended for any amount of time. Before making any repairs or adjustments to the machine.
MAINTENANCE WARNING CAUTION Always exercise the stopping procedure before servicing or lubricating the unit. Always verify fluid levels and check for leaks after changing fluids. After servicing the unit, replace and fasten all guards, shields, and covers to their original positions before resuming operation. Do not drain oil onto ground, into open streams, or down sewage drains.
SERVICE Assembly and disassembly should be performed by a service technician who has been factory trained on MBW equipment. The unit should be clean and free of debris. Pressure washing before disassembly is recommended. Service Tools 01058 6-Pack Grounder Pounder® Exciter Oil • Prior to assembly, wash all parts in a suitable cleaner or solvent. 01629 Test Mat 12100 Decal Set Part No. • Check moving parts for wear and failure.
Changing Exciter Oil Refer to EXCITER ASSEMBLY, page 12. 1. Allow machine to completely cool down before performing any service or maintenance. 2. Clean debris from exciter, engine deck and base plate. 3. Drain all gasoline from fuel tank. 4. Drain oil from engine or remove engine from engine deck before proceeding to next step. Failure to do this could result in damage to the engine. 5. Tilt plate forward so the oil drains from the exciter housing into a pan as shown in Figure 3. 6. 7.
Exciter Assembly exciter shaft into the housing until the bearing on the pulley side of the shaft is properly seated in the housing. Refer to EXCITER ASSEMBLY, page 12. 1. 2. 9. Prior to assembly, clean all parts in a suitable solvent cleaning solution. 10. Install a new seal into the pulley side exciter cover. Lubricate lip of seal with fresh exciter oil. Inspect all part for wear or failure and replace if necessary as described in Parts Replacement Cycles and Tolerances section of this manual. 3.
REPLACEMENT PARTS The warranty is stated in this book on page 18. Failure to return the Warranty Registration Card renders the warranty null and void. MBW has established a network of reputable distributors/ dealers with trained mechanics and full facilities for maintenance and rebuilding, and to carry an adequate parts stock in all areas of the country. Their sales engineers are available for professional consultation.
This page intentionally left blank.
6(5,(6 6(5,(6 EXCITER ASSEMBLY - 12 -
ITEM 1. 2. 3. 4. 5. 6. 7. 9. 10. 11. 12. PART NO. 01070 01072 01191 15946 15956 17179 18629 16912 19832 19834 19833 F0205SP F042007FWS F0618SPP 13. 14. F0618SPP F0612SP 8. DESCRIPTION BEARING, BALL FILTER, FELT RETAINING RING, INTERNAL EXCITER COVER, SEALED GASKET SEAL, OIL BOTTOM PLATE BOTTOM PLATE EXCITER SHAFT EXCITER SHAFT, 1800 EXCITER COVER, PULLEY PIN, SPIROL, 1/8 X 5/8 RD HEX HAED FLANGE SCREW, 1/4-20 X 1” LG.
:$7(5 7$1.
ITEM 1. 2. 3. 4. 5. 6. 7. 14. 15. 16. 17. 18. 19. 20. 21. 22. 23. 24. 25. 26. 27. 28. 29. 30. 31. PART NO. 00031 00032 01011 01099 6931 07636 12860 17210 20382 14993 16105 18633 18628 16913 15994 16953 19848 19135 19630 F0203HTB F042004FWS F052406HCS F051808FSS F051814HCS F05LW F05SW F061605FSS F061605FWS F061607HCS F06LW F06SW F081306HCS F081307HCS F08LW M12ETLW 32. 33. 34. 18667 ROLLCAGE, OPTIONAL F051806FWS HEX HEAD FLANGE SCREW, 5/16-18 X 3/4 LG F0518FN FLANGE NUT, 5/16-18 35. 36. 37. 38.
6(5,(6 6(5,(6 HANDLE ASSEMBLY - 16 -
ITEM 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 16. 17. 18. 19. 20. 21. 22. 23. 24. 25. 26. 27. 28. 29. 30. PART NO. 01001 01018 01019 01056 06075 16759 16932 16954 16955 18634 16959 16963 18638 19755 19851 19854 19856 F042004FWS F051804FWS F05SW F061606FWS F061610FWS F0616ELN F0616FN F06SW F081307HCS F081310HCS F08LW F08SW M12ETLW DESCRIPTION RETAINING RING NYLON BUSHING, OUTER NYLON BUSHING, INNER HAIR PIN, 1/8 DIA. X 2-3/8 LG.
WARRANTY WHAT DOES THIS WARRANTY COVER? MBW, Incorporated (MBW) warrants each New Machine against defects in material and workmanship for a period of twelve (12) months. "New Machine" means a machine shipped directly from MBW or authorized MBW dealer to the end user. This warranty commences on the first day the machine is sold, assigned to a rental fleet, or otherwise put to first use. MBW warrants each Demonstration Machine against defects in material and workmanship for a period of six (6) months.
