M145-107T POWERDRIVE Euro Instruction manual Manuel d’instructions Manuale di istruzioni Bedienungsanleitung Manual de las instrucciones Instructieboekje Please read these instructions carefully and make sure you understand them before using this machine. Lesen Sie diese Anweisungen sorgfältig durch und machen Sie sich mit dem Inhalt vertraut, bevor Sie diese Maschine benutzen. 589 22 86-40 Rev. 4 Merci de lire trés attentivement le manuel d'instructions.
1 Safety rules. Sicherheitsvorschriften. Règles de sécurité. Reglas de seguridad. Norme antinfortunistiche. Veiligheidsregels. 2 Assembly. Montage. Montage. Montaje. Montaggio. Montering. 19 3 Functional description. Funktionsbeschreibung. Description du fonctionnement. Descripción del funcionamiento. Funzionamento. Beschrijving van functies. 27 4 Before starting. Vor dem Start. Avant de démarrer. Antes del arranque. Prima dell’avviamento. Maatregelen vóór het starten. 35 5 Driving. Betrieb.
1. Safety Rules Safe Operation Practices for Ride-On Mowers IMPORTANT: THIS CUTTING MACHINE IS CAPABLE OF AMPUTATING HANDS AND FEET AND THROWING OBJECTS. FAILURE TO OBSERVE THE FOLLOWING SAFETY INSTRUCTIONS COULD RESULT IN SERIOUS INJURY OR DEATH. I. TRAINING III. OPERATION • Read the instructions carefully. Be familiar with the controls and the proper use of the equipment. • Never allow children or people unfamiliar with the instructions to use the lawnmower.
WARNING: CHILDREN CAN BE INJURED BY THIS EQUIPMENT. The American Academy of Pediatrics recommends that children be a minimum of 12 year of age before operating a pedestrian controlled lawn mower and a minimum of 16 years of age before operating a riding lawn mower. • • • • When loading or unloading this machine, do not exceed the maximum recommended operation angle of 15°.
1. Sicherheitshinweise Hinweise zur sicheren Bedienung von Aufsitzmähern WICHTIG: DIESE MÄHMASCHINE KANN HÄNDE ODER FÜSSE ABTRENNEN UND GEGENSTÄNDE DURCH DIE LUFT SCHLEUDERN. BEI MISSACHTUNG DER FOLGENDEN SICHERHEITSHINWEISE BESTEHT DIE GEFAHR SCHWERER VERLETZUNGEN ODER TÖDLICHER UNFÄLLE. • I. SCHULUNG • Lesen Sie die Anweisungen gründlich durch. Machen Sie sich mit den Bedienelementen und dem vorschriftsmäßigen Gebrauch des Gerätes vertraut.
• • • - bevor Sie den Rasenmäher prüfen, reinigen oder Arbeiten daran ausführen. - nachdem Sie einen Fremdkörper getroffen haben. Untersuchen Sie den Rasenmäher auf Schäden und führen Sie Reparaturen durch, bevor Sie die Maschine neu starten und bedienen. - Wenn die Maschine anfängt, ungewöhnlich zu vibrieren, überprüfen Sie dies sofort. Schalten Sie den Antrieb der Zusatzgeräte beim Transport oder wenn diese nicht verwendet werden aus.
1. Règles de Sécurité Conseils pour l’utilisation en toute sécurité des tracteurs de pelouse ATTENTION: CE TRACTEUR DE PELOUSE EST CAPABLE D’AMPUTER MAINS OU PIEDS ET DE PROJETER DES OBJETS. L’INOBSERVATION DES RÈGLES DE SÉCURITÉ CI-DESSOUS PEUT ÊTRE LA CAUSE DE BLESSURES SÉRIEUSES VOIRE MORTELLES. I. PRÉCAUTIONS D’UTILISATION • • Lisez toutes les instructions soigneusement. Familiarisez vous avec les commandes pour appprendre à utiliser efficacement cette machine.
- • • • avant de retirer un objet coincé dans le tracteur de pelouse. Dans ce cas inspecter aussitôt la machine pour s’assurer qu’elle n’est pas endommagée et, si nécessaire, faire ou faire faire impérativement les réparations avant de la remettre en marche et de la faire fonctionner à nouveau. - si la machine commence à vibrer anormalement. Dans ce cas vérifier immédiatement le carter de coupe. Débrayer systématiquement les lames quand le tracteur n’est pas utilisé ou quand il doit être transporté.
1. Reglas De Seguridad Prácticas de Operación Seguras para las Segadoras Conducibles IMPORTANTE: ESTA MAQUINA CORTADORA ES CAPAZ DE AMPUTAR LAS MANOS Y LOS PIES Y DE LANZAR OBJETOS. SI NO SE OBSERVAN LAS INSTRUCCIONES DE SEGURIDAD SIGUIENTES SE PUEDEN PRODUCIR LESIONES GRAVES O LA MUERTE. I. INSTRUCCIÓN III. OPERACIÓN • Lea todas las instrucciones cuidadosamente.
• • Pare el motor y desenganche la transmisión a los accesorios - antes de agregar combustible; - antes de quitar el recogedor del césped; - antes de haces ajustes de altura a menos que los ajustes pueden ser hechos de la posición del operador. Reduzca los ajustes de la aceleración durante el tiempo que el motor se apague, si el motor viene diseñado con una válvula de apagado, sierre el combustible cuando halla terminado de segar. ADVERTENCIA: LOS NIÑOS PUEDEN RESULTAR HERIDOS POR ESTE EQUIPO.
1. Norme Antinfortunistiche Regole di sicurezza per trattorini da prato ATTENZIONE: QUESTO TRATTORINO TOSAERBA HA UNA POTENZA SUFFICIENTE AD AMPUTARE MANI E PIEDI E A SCAGLIARE OGGETTI. LA MANCATA OSSERVANZA DELLE SEGUENTI ISTRUZIONI ANTINFORTUNISTICHE POTREBBE CAUSARE LESIONI GRAVI E PERSINO IL DECESSO DELLA VITTIMA. I. ADDESTRAMENTO ALL’USO III. FUNZIONAMENTO • Studiare attentamente le istruzioni. Acquisire dimestichezza con i comandi e conoscere a fondo l’uso corretto dell’equipaggiamento.
• • • Disinnestare la trasmissione del moto agli accessori durante il trasporto del macchinario oppure quando non è in uso. Spegnere il motore e disinnestare la motorizzazione degli accessori nei seguenti casi: - prima di fare rifornimento; - prima di smontare il contenitore dell’erba tagliata; - prima di regolare l’altezza, a meno che le regolazioni non possano essere eseguite dal posto dell’operatore. Ridurre la velocità, con la leva dell’acceleratore, per rallentare il motore prima dello spegnimento.
1. Veiligheidsregels Veilige bedieningsmethoden voor zittrekkers BELANGRIJK: DEZE MAAIMACHINE KAN HANDEN EN VOETEN AMPUTEREN EN VOORWERPEN WEGSLINGEREN. HET NIET OPVOLGEN VAN DEZE VEILIGHEIDSINSTRUCTIES KAN ERNSTIG OF DODELIJK LETSEL TOT GEVOLG HEBBEN. I. TRAINING III. BEDIENING • Lees de instructies aandachtig. Zorg dat u vertrouwd bent met de bedieningselementen en het juiste gebruik van de machine. • Laat kinderen of mensen die niet bekend zijn met de instructies, de maaimachine niet gebruiken.
• Minder gas tijdens het uitlopen van de motor, en als de motor met een afsluitklep is uitgerust, moet u de brandstoftoevoer aan het einde van het maaien afsluiten. • • • • WAARSCHUWING: KINDEREN KUNNEN VERWOND WORDEN DOOR DEZE APPARATUUR. De American Academy of Pediatrics adviseert dat kinderen minimaal 12 jaar moeten zijn voordat ze een lopend bediende gazonmaaier gebruiken en minimaal 16 jaar moeten zijn voordat ze een rijdende gazonmaaier gebruiken.
Complies with the provisions and current amendments of the Directives and Standards shown in the product performance chart. * The power rating as declared by the engine manufacturer is the average gross power output at the specified RPM of a typical production engine for the engine model measured using SAE Standards for engine gross power. Please refer to the engine manufacturer for details. M145-107T 11.
These symbols may appear on your machine or in the literature supplied with the product. Learn and understand their meaning. Diese Symbole finden Sie auf Ihrer Maschine oder in Unterlagen, die mit dem Produkt ausgehändigt wurden. Bitte machen Sie sich mit deren Bedeutung vertraut. Ces symboles peuvent figurer sur tracteur ou dans les publications fournies avec le produit. Apprenez à comprendre la signification de ces symboles.
These symbols may appear on your machine or in the literature supplied with the product. Learn and understand their meaning. Diese Symbole finden Sie auf Ihrer Maschine oder in Unterlagen, die mit dem Produkt ausgehändigt wurden. Bitte machen Sie sich mit deren Bedeutung vertraut. Ces symboles peuvent figurer sur tracteur ou dans les publications fournies avec le produit. Apprenez à comprendre la signification de ces symboles.
01738 AUGEN SCHÜTZEN EXPLOSIVE GASE KANN ERBLINDUNG ODER VERLETZUNGEN VERURSACHEN ZU VERMEIDEN: • FUNKEN • FEUER • RAUCHEN SCHWEFELSÄURE KANN ERBLINDUNG ODER SCHWERE VERÄTZUNGEN VERURSACHEN. AUGEN UNVERZÜGLICH MIT WASSER AUSSPÜLEN. SOFORT ÄRZTLICHE HILFE AUFSUCHEN. GEVAAR OGEN BESCHERMEN EXPLOSIEVE GASSEN KUNNEN BLINDHEID OF LETSEL VEROORZAKEN. GEEN • VONKEN • VUUR • ROKEN ZWAVELZUUR KAN BLINDHEID OF ERN-STIGE BRANDWONDEN VER-OORZAKEN. OGEN ONMIDDELLIJK MET WATER SPOELEN.
2. Assembly. 2. Montage. 2. Montage. 2. Montaje. 2. Montaggio. 2. Montering. Unassembled Parts Partes no montadas Before the tractor can be used certain parts must be assembled, which for transportation reasons are enclosed in the packing. Antes de poder utilizar el tractor, hay que montar algunas piezas que, por razones de transporte, van empaquetadas en el embalaje.
2 • • • • • 1 VOLANT DE DIRECTION Monter la rallonge d'arbre de direction (1). Positionner le cache sur la colonne de direction. S'assurer que les ergots du cache colonne de direction sont bien clipsés dans les quatre orifices du tableau de bord. Enlevez le manchon de direction du volant de direction et glissez le manchon sur l’arbre de rallonge. Vérifier que les roues avant sont bien alignées droit vers l’avant et positionner le volant sur le moyeu.
2 NOTE: Ensure “UP” reads right side up and arrow is pointing up on winged washers as shown. 5 • 3 7 • 1 8 6 4 Remove tape (13) and discard. WARNING: Ensure the seat assembly is securely fastened to the seat pan before occupying or operating tractor. 7 Lower seat into operating position and sit on seat. Press clutch/brake pedal all the way down. If operating position is not comfortable, adjust seat. TO ADJUST SEAT Grasp adjustment handle (14) and pull up.
2 • Levez le siège. Montez les boulons (10) et les rondelles papillons (11) et serrez fermement au niveau des patins avant (12). REMARQUE : assurez-vous que « UP » se lise côté droit vers le haut et que la flèche pointe vers le haut sur les rondelles papillon, comme illustré. 5 3 7 6 4 • Retirez le ruban adhésif (13) et mettez-le au rebut. 1 8 AVERTISSEMENT : assurez-vous que l'ensemble de siège est solidement fixé sur le plateau de siège avant de monter à bord du tracteur ou de l'utiliser.
2 • Sollevare il sedile. Montare le viti (10) e le rondelle alettate (11) e serrarli sui cuscini anteriori (12). NOTA: Assicurarsi che la scritta "UP" (su) sia leggibile e che la freccia sia rivolta in alto verso le rondelle alettate, come mostrato in figura. 5 3 7 1 8 6 4 • Togliere il nastro (13) e gettarlo. AVVERTENZA: Assicurarsi che il complessivo sedile sia saldamente fissato alla piastra del sedile prima di occupare o utilizzare il trattore.
2 1. 2. 3. 4. A. 5. 6. 7. 1. 2. 3. 4. A. 5. 6. 7. Seat pan Terminal Cover Cable (+) Cable (-) Front of tractor Fender Battery terminal Battery Sitzwanne Klemmenabdeckung Kabel (+) Kabel (-) Vorderseite des Rasenmähers Schutzblech Batteriepol Batterie 1. 2. Embase du siège Capuchon de protection 3. Câble (+) 4. Câble (-) A. Vers l'avant du tracteur 5. Carrosserie 6. Borne de batterie 7. Batterie 1. 2. 3. 4. A. 5. 6. 7.
2 WARNING: Positive terminal must be connected first to prevent sparks from accidental grounding. Remove terminal caps and discard. Connect the red cable to (+) and then the black earth cable to (-). Screw tight the cables. Grease the battery cables with petroleum jelly to prevent corrosion. WARNUNG: Der Pluspol muss zuerst angeschlossen werden, um Funken durch unbeabsichtigte Erdung zu vermeiden. Entfernen Sie die Endkappen und entsorgen Sie diese.
2 PARA AJUSTAR LAS RUEDAS CALIBRADORAS (si se incluyen) Las ruedas calibradoras están bien ajustadas cuando se encuentran un poco a distancia del terreno al mismo tiempo que la segadora esté a la altura de corte deseada. Entonces las ruedas calibradoras mantienen el conjunto segador en posición para prevenir el corte raspeo en casi todos los terrenos. • Ajuste las ruedas calibradoras con el tractor en una superficie nivelada plana.
3. Functional description. 3. Funktionsbeschreibung. 3. Description du fonctionnement. 3. Descripción del funcionamiento. 3. Funzionamento. 3. Beschrijving van functies 2 1 5 3 11 8 7 4 6 9 Positioning of controls 1. Light switch (if equipped) 2. Throttle control 3. Brake and clutch pedal 4. Forward/Reverse Drive Pedal 5. Connection/Disconnection of the Cutting Unit 6. Quick lifting/lowering of the cutting unit 7. Ignition lock 8. Parking Brake 9. Free-wheel Control Lever 11.
3 2 1 5 3 11 8 7 4 6 9 Emplacement des commandes 1. 2. 3. 4. 5. 6. 7. 8. 9. 11. Comandi 1. Interruttore luci (se installato) 2. Acceleratore 3. Pedale freno/frizione 4. Pedale Marcia avanti/indietro 5. Inserimento/disinserimento del dispositivo di taglio 6. Sollevamento/abbassamento del tagliaerba 7. Chiave di accensione 8. Freno di parcheggio 9. Inserimento/disinserimento ruote 11.
3 1. Light switch (if equipped) 1 1. Lichtschalter (falls installiert) 1. Interrupteur des phares (le cas échéant) 7 34 01 1. Interruptor de alumbrado (si se incluyen)) 1. Interruttore luci (se in dotazione) 1. Schakelaar verlichting (indien aanwezig) 2. Throttle control The throttle control regulates the engine revs and thus the rotation speed of the blades. = Full speed = Idling speed 2.
3 3. Clutch/Brake Pedal Used for declutching and braking the tractor and starting the engine. 3 3. Kupplungs/Bremspedal Wird zum Entkuppeln und Bremsen des Traktors und zum Starten des Motors benutzt. 3. Pédale de frein/D’embrayage Permet de débrayer et de freiner le tracteur et de démarrer le moteur. 3. Pedal del embrague/Freno Se usa para desembragar y frenar el tractor y arrancar el motor. 3.
3 5. Commande d'embrayage et de débrayage du carter de coupe Pousser le levier vers l'avant et le verrouiller pour embrayer le carter de coupe. Les courroies d'entraînement seront alors en tension et les lames commenceront à tourner. Ramener le levier vers l'arrière pour débrayer le carter de coupe, les lames seront alors freinées par le frottement des patins de frein sur les poulies d'entraînement. 5 5.
3 7 OFF ROS ON ON 7. Ignition Lock 02927 START 7. Cerradura de encendido There are four different positions for the ignition key: OFF All electric current broken. ROS ON Reverse Operation System (ROS) connected ON Electric current connected. START Start motor connected. Reverse Operation System (ROS) - Allows operation of mower deck or other powered attachment while in reverse (See section 5 - "Driving").
3 8. Parking brake Connect the parking brake in the following way: 1. Press down the brake pedal to bottom position. 2. Move the parking brake lever upwards and hold in this position. 3. Release the brake pedal. To release the parking brake all that is necessary is to push down the brake pedal. 8 8. Feststellbremse Die Feststellbremse wie folgt ansetzen: 1. Bremspedal ganz durchtreten. 2. Feststellbremshebel nach oben führen und in dieser Stellung halten. 3. Bremspedal loslassen.
3 9. Blocage et déblocage de la roue libre Pour remorquer ou déplacer le tracteur sans l'aide du moteur, la commande de roue libre, qui se trouvesur le tablier arrière du châssis du tracteur, doit être tirée vers l'extérieur et bloquée dans cette position. REMARQUE : Pour débloquer la commande de roue libre, appuyez sur la pédale de frein/embrayage. 9 9.
4. Before starting. 4. Vor dem Start. 4. Avant de démarrer. 4. Antes del arranque. 4. Prima dell’avviamento. 4. Maatregelen vóór het starten. Reposición de combustible Filling up The engine should be run of pure (not oil mixed) unleaded petrol. Do not fill beyond the lower edge of the filling hole. Do not fill over max level. El motor ha de funcionar con gasolina pura (sin mezcia de aceite), sin plomo. El nivel no ha de sobrepasar el borde inferior del orificio de llenado.
4 Oil level Nivel de aceite The combined oil refilling cap and the oil stick is accessible when the bonnet is lifted forwards. The oil level in the engine should be checked before each run. Make sure that the tractor is horizontal. Unscrew the oil stick and wipe clean. Replace the oil stick and screw tight. Remove again and check the level. La tapa combinada para el llenado de aceite y para la varilla de nivel queda accesible después de haber levantado hacia adelante el capó del motor.
5. Driving. 5. Betrieb. 5. Conduite. 5. Conducción. 5. Guida. 5. Rijden. Starting of motor 47 3 Sit on seat in operating position, depress brake pedal and set parking brake. Make sure that the cutting unit is in the transport position (top position) and that the attachment clutch control for connection/disconnection of the cutting unit is in the disconnection position.
5 Pull out the choke control (if engine is cold). Den Kaltstarthebel herausziehen (nur bei kaltem Motor). Si le moteur est froid: Tirer la commande de starter. 01 3 36 Extraer el estrangulador (únicamente si el motor está frío). Estrarre il comando dello choke (in caso di partenza a freddo). Trek de choke uit (geldt alleen indien de motor koud is). Warm motor: Push gas control half way to full gas position " ". Bei warmem Motor: Gashebel in die Vollgasstellung " schieben.
5 Tourner la clef de contact en position de démarrage “START”. REMARQUE Ne pas faire tourner le démarreur pendant plus de 5 secondes à la fois. Si le moteur ne démarre pas, attendre une dizaine de secondes avant de refaire un essai de démarrage. Ponga la llave de encendido en la posición de arranque ”START”. NOTA No haga funcionar el motor de arranque más de unos 5 segundos a la vez. Si el motor no arranca, espere unos 10 segundos antes de hacer otra tentativa. 02927 Girare la chiave su “START”.
5 IMPORTANT! COLD STARTING ¡IMPORTANTE! ARRANQUE EN FRÍO COLD STARTING (BELOW 40°F [4°C]) - AFTER STARTING ENGINE AND BEFORE DRIVING, LET TRANSMISSION WARM UP FOR ONE (1) MINUTE BY RELEASING CLUTCH/ BRAKE PEDAL. ARRANQUE EN FRÍO (TEMPERATURA INFERIOR A 4°C[40°F]): DESPUÉS DE ARRANCAR EL MOTOR Y ANTES DE INICIAR LA MARCHA, DEJE QUE LA TRANSMISIÓN SE CALIENTE DURANTE UN (1) MINUTO. PARA ESTO, DESENGANCHAR EL PEDAL DEL EMBRAGUE/FRENO.
5 Moverse hacia adelante y hacia atrás To Move Forward and Backward The direction and speed of movement is controlled by the forward and reverse drive pedals. • Start tractor and release parking brake. • Slowly depress forward or reverse drive pedal to begin movement. Ground speed increases the further down the pedal is depressed. La dirección y la velocidad de movimientos están controlados por los pedales de marcha adelante y atrás. • Poner en marcha el tractor y quitar el freno de mano.
5 ROS "ON" ROS "AN" ROS "ON" ROS "ON" ROS "ON" ROS "ON" 02828 Reverse Operation System (ROS) Engine "ON" (Normal Operating) Motor "AN" (Normalbetrieb) Moteur "ON" (Fonctionnement normal) Motor "ON" (Funcionamiento Normal) Motore "ON" (Funzionamento normale) Motor "ON" (normaal functioneren) Sécurité Marche Arrière (ROS) Your tractor is equipped with a Reverse Operation System (ROS).
5 Cutting tips Sistema per operazioni in retromarcia (ROS) • Il Vostro trattore possiede un Sistema per operazioni in retromarcia (ROS). Qualsiasi tentativo da parte dell’operatore di guidare nella direzione opposta con la frizione abbassata comporterà lo spegnimento del motore se la chiave di accensione non è inserita nel ROS nella posizione "ON". ATTENZIONE! Fare retromarcia con la frizione abbassata durante la guida è sconsigliato.
5 Conseils pour la tonte • • • • • • • Consigli per il taglio dell’erba Retirer de la pelouse, les pierres et autres objets qui pourraient être propulsés par les lames et devenir ainsi des projectiles dangereux. Localiser et marquer les pierres et autres obstacles fixes afin d'éviter une éventuelle collision pendant la tonte. Commencer par couper assez haut, puis réduire progressivement cette hauteur de coupe jusqu'à obtention du résultat souhaité.
5 ATTENTION! • • • Ne jamais utiliser un tracteur sur des pentes excédant 15°. Les risques de renversement étant alors très importants. Ne jamais rouler parallèlement à la pente du fait des risques de renversement. Toujours rouler perpendiculairement à la pente, aussi bien en montant, qu'en descendant. Ne jamais arrêter ou démarrer un tracteur en pente. ADVERTENCIA! • • • No conduzca por terreno de inclinación superior a 15°, pues hay riesgo de sobrepeso en la parte posterior.
5 Switching off the engine Move the attachment clutch control to disengaged position. Move the throttle control to fast position. Lift up the cutting unit and turn the ignition key to “STOP” position. Abschalten des Motors Stellen Sie den Kupplungshebel für das Anbauwerkzeug in die Position "disengaged" (ausgekuppelt). Stellen Sie die Drosselklappensteuerung in die Position "Fast" (schnell). Heben Sie die Schneidvorrichtung an und drehen Sie den Zündschlüssel in die Position "STOP".
6. Maintenance, Adjustment. 6. Wartung (Instandhaltung), Einstellung. 6. Entretien, Réglages. 6. Mantenimiento, Ajuste. 6. Manutenzione. 6. Onderhoud, Afstelling. WARNING! ADVERTENCIA! Before servicing the engine or cutting unit the following shall be carried out: • Press down the clutch/brake pedal and engage the parking brake lever. • Move connection/disconnection control to disengaged position. • Switch off engine. • Remove the ignition cable from the plug.
6 Motorhaube • • • 1 • • Heben Sie die Abdeckung an. Entfernen Sie den Scheinwerfer-Kabelstecker. Stellen Sie sich vor den Traktor. Fassen Sie die Haube an den Seiten, kippen Sie diese nach vorn, und heben Sie sie vom Traktor ab. Um sie erneut zu installieren, schieben Sie die Scharnierhalterungen der Haube in die Langlöcher des Rahmens. Schließen Sie den Scheinwerfer-Kabelstecker wieder an, und schließen Sie die Motorhaube.
6 Wartung 5 2 HINWEIS: Regelmäßige Wartung ist die Grundlage für den sicheren und störungsfreien Betrieb Ihres Traktors. WARNUNG: Ziehen Sie immer den Zündkerzenstecker ab. Damit verhindern Sie einen unvorhergesehenen Motorstart bei Reparaturen, Kontrollen und Wartungsarbeiten. Vor jedem Gebrauch: • Kontrollieren Sie den Ölstand und schmieren Sie bei Bedarf alle Drehpunkte. • Kontrollieren Sie, dass alle Schrauben, Muttern und Splinte vorhanden und fest angezogen sind.
6 Mantenimiento 5 2 NOTA: El mantenimiento periódico ha de hacerse con regularidad a fin de mantener el tractor en buen estado. ADVERTENCIA: Antes de efectuar cualquier reparación, inspección o maintenimiento, desconectar el cable de la bujía a fin de evitar accidentes. Antes de cada uso de la máquina: • Controlar el aceite, si es necesario lubricar los puntos de pivotaje. • Controlar que todos los pernos, tuercas y pasadores estén en su sitio y bien seguros.
6 Onderhoud 5 2 N.B.: Om uw tractor in goede conditie te houden, moeten er regelmatig onderhoudsbeurten uitgevoerd worden. WAARSCHUWING: Schakel altijd eerst de bougieleiding uit voor u herstellingen, inspecties of onderhoud uitvoert. Dit om te voorkomen dat de machine per ongeluk start. Voor elk gebruik: • Controleer het oliepeil en smeer de draaipunten indien nodig. • Controleer of alle bouten, moeren en splitpennen op hun plaats zitten en goed vast zitten.
6 PARA CAMBIAR EL ACEITE ATENCIÓN: El aceite estará caliente si el motor ha estado funcionando durante un tiempo prolongado inmediatamente antes de drenarlo. • Deslice el extensor de drenaje del aceite sobre el chasis situado por debajo del orificio de drenaje. • Coloque un recipiente debajo del extensor de drenaje para recoger el aceite. • Afloje y retire el tapón de drenaje del aceite con una llave de vaso de 1/2 pulgadas (12 puntos) (recomendada para el extensor).
6 SERVICE RECORD Fill in dates as you complete regular service As Needed Every 8 Hours Every Every Every Every 25 Hours 50 Hours 100 hours 200 Hours Change engine oil (without oil filter) .................................. ................. ................. ....... • Change engine oil (with oil filter) ....................................... ................. ................. ................. ....... Lubricate pivot points......................................................... ................. .
6 SCHEMA D'ENTRETIEN Consigner les dates d'intervention après chaque opération d'entretien. Selon les besoins Toutes les 8 H Toutes les 25 H Vidange de l'huile moteur (sans filtre à huile) ................... ................. ................. ....... Toutes les 50 H • Vidange de l'huile moteur (avec filtre à huile).................... ................. ................. ................. ....... Graissage des articulations ............................................... ................. ..........
6 DATI DI SERVIZIO Compilare ogni qualvolta si esegue un regolare servizio Necessità Ogni 8 ore Ogni 25 ore Cambio dell'olio (Senza filtro dell’olio) ............................... ................. ................. ....... Ogni 50 ore • Cambio dell'olio (Con filtro dell’olio) .................................. ................. ................. ................. ....... Lubrificazione punti di articolazione................................... ................. ................. .......
6 Operator Presence System and Reverse Operation System (ROS) Be sure operator presence and reverse operation systems are working properly. If your tractor does not function as described, repair the problem immediately. • The engine should not start unless the brake pedal is fully depressed, and the attachment clutch control is in the disengaged position.
6 Sistema de Presencia Operador y Sistema de Funcionamiento Atrás (ROS) Asegurarse de que los sistemas de presencia operador y funcionamiento atrás funcionen adecuadamente. Si tu tractor no funciona como descrito, hay que reparar el problema inmediatamente. • El motor no tiene que arrancar hasta que le pedal del freno no esté completamente presionado, y el mando del embrague esté en la posición desembragada.
6 To Check Brake Controlar El Freno If tractor requires more than five (5) feet to stop at highest speed in highest gear on a level, dry concrete or paved surface, then brake must be serviced. You may also check brake by: 1. Park tractor on a level, dry concrete or paved surface, depress brake pedal all the way down and engage parking brake. 2. Disengage transmission by placing freewheel control in “transmission disengaged” position.
6 Messerbalken Für beste Mähergebnisse müssen die Messerbalken immer opti mal geschliffen sein. Wechseln Sie verbogene oder beschädigte Messerbalken sofort aus. Sie werden mit einer Feile oder einer Schleifscheibe geschärft. HINWEIS: Um eine Unwucht zu vermeiden, müssen beide Seiten der Messerbalken gleichmäßig geschärft und auf Unwucht geprüft werden. WECHSELN DER MESSERBALKEN: • Fahren Sie das Mähdeck in die höchste Position, um Zugriff zu den Messerbalken zu bekommen.
6 Lame Per avere il migliore risultato di taglio, è necessario che le lame siano ben affilate. Sostituirle se usurate o danneggiate. A tale scopo utilizzare una lima o una mola. NOTA: E’ importante affilare le due estremità della lama in modo uniforme per non creare disequilibri. RIMOZIONE DELLE LAME: • Sollevare la macchina per avere accesso alle lame. • Rimuovere il bullone dalla lama. • Montare una nuova lama o una lama con palettaura posteriore rivolta verso il piatto, come indicato.
6 M B Q F R A P E C D K L To Remove Mower Entfernen Des Mähers • • • Place attachment clutch in “DISENGAGED” position. Lower attachment lift lever to its lowest position. Remove retainer spring (K), slide collar (L) off and push housing guide (P) out of bracket. • Remove clutch cable spring (Q) from idler arm (R). CAUTION: Belt tension rod is spring loaded. Have a tight grip on rod and release slowly. • Remove mower belt from clutch pulley (M).
6 • • De Maaiunit Verwijderen Pour Démonter La Faucheuse Placez l’embrayage de l’accessoire en position “DÉGAGÉ”. Faites descendre le levier de levage de l’accessoire dans sa position la plus basse. • Retirer le ressort de retenue (K), retirer le collier (L) en le faisant glisser et pousser le guide-capot (P) pour le sortir de la patte. • Retirer le ressort du câble d’embrayage (Q) du bras de renvoi (R). PRUDENCE: Le tendeur de la courroie est à ressort. Saisissez-le fermement et libérez-le lentement.
6 M V R To Replace Mower Drive Belt Austauschen des Mäher-Treibriemens MOWER DRIVE BELT REMOVAL 1. Park tractor on a level surface. Engage parking brake. 2. Lower attachment lift lever to its lowest position. 3. Remove any dirt or grass clippings which may have accumulated around mandrels and entire upper deck surface. 4. Remove belt from clutch pulley (M), both mandrel pulleys (R) and all idler pulleys (V). AUSBAU DES MÄHER-TREIBRIEMENS 1. Stellen Sie den Traktor auf einer ebenen Fläche ab.
6 Pour remplacer la courroie de transmission Sostituzione della cinghia di trasmissione del rasaerba DÉMONTAGE DE LA COURROIE DE TRANSMISSION DE LA TONDEUSE 1. Garez le tracteur bien à plat. Engagez le frein de stationnement. 2. Faites descendre le levier de levage de l’accessoire dans sa position la plus basse. 3. Eliminez la saleté ou les brins d’herbe qui s’accumulent autour des arbres et à la surface du pont supérieur. 4.
6 Fig. 1 Fig. 3 02548 A B B Fig. 4 02473 B 02473 A 02948 Fig. 2 02966 B 02473 A 02473 A 02950 To Level Mower FRONT-TO-BACK ADJUSTMENT Make sure tires are properly inflated to the PSI shown on tires. If tires are over or under inflated, it may affect the appearance of your lawn and lead you to think the mower is not adjusted properly. IMPORTANT: Deck must be level side-to-side.
6 Fig. 1 Fig. 3 02548 A B B Fig. 4 02473 B 02473 A 02948 Fig. 2 02966 B 02473 A 02473 A 02950 Ausnivellieren des Mähers 5. Überprüfen Sie die Messungen noch einmal und stellen Sie die Stellmuttern nötigenfalls nach, bis beide Seiten gleich sind. Vergewissern Sie sich, dass die Reifen auf den Druck aufgeblasen sind, der auf den Reifen angegeben ist.
6 Fig. 1 Fig. 3 02548 A B B Fig. 4 02473 B 02473 A 02948 Fig. 2 02966 B 02473 A 02473 A 02950 Pour mettre la tondeuse à niveau RÉGLAGE D’AVANT EN ARRIÈRE IMPORTANT: Le pont doit être mis à niveau bilatéralment. Pour que la coupe soit parfaite, les lames de la tondeuse doivent être réglées de façon à ce que la pointe avant se trouve 1/8 –1/2 pouce plus bas que la pointe arrière lorsque la tondeuse est dans sa position la plus élevée. DANGER: Les lames sont affûtées.
6 Fig. 1 Fig. 3 02548 A B B Fig. 4 02473 B 02473 A 02948 Fig. 2 02966 B 02473 A 02473 A 02950 Nivelar el cortacésped AJUSTE DE LA PARTE DELANTERA A LA TRASERA IMPORTANTE: la cubierta ha de ser nivelada de un lado al otro. Para obtener los mejores resultados de corte, las hojas del cortacésped han de ajustarse de modo que la punta frontal sea entre 1/8" y 1/2" más bajo que la punta trasera cuando la cortacésped está en su posición más alta. PRECAUCIÓN: Las hojas cortan.
6 Fig. 1 Fig. 3 02548 A B B Fig. 4 02473 B 02473 A 02948 Fig. 2 02966 B 02473 A 02473 A 02950 Livellamento del rasaerba 5. Verificare nuovamente le misurazioni, regolare secondo necessità finché entrambi i lati siano pari. Verificare che i pneumatici siano adeguatamente gonfati in base ai psi riportati sugli stessi.
6 Fig. 1 Fig. 3 02548 A B B Fig. 4 02473 B 02473 A 02948 Fig. 2 02966 B 02473 A 02473 A 02950 De maaiunit nivelleren AFSTELLING BOOR-EN ACHTERZIJDE BELANGRIJK: Het oppervlak van de maaier moet overal dezelfde hoogte hebben. Voor de beste maairesultaten moeten de maaimessen zodanig worden afgesteld dat de voorkant 1/8” tot 1/2” lager is dan de achterkant wanneer de maaier in de hoogste stand staat. OPGELET: De messen zijn scherp.
6 Replacement of drive belt Dismantle the cutting unit as described previously Engage the parking brake and work off the belt upwards from the pulley (1), the clutch pulley (2) and the engine's drive wheel (3). Work off the belt upwards from the pulley at the rear axle (4). 3 Auswechsein des Treibriemens 2 Mähaggregat ausbauen. Feststellbremse ansetzen und den Riemen vom Laufrad (1), dem Kupplungsriemenrad (2) und dem Motorantriebsrad (3) abbauen.
6 MAINTENANCE - TRANSAXLE The transaxle was sealed at the factory and fluid maintenance is not required. Should the transaxle ever leak or require servicing, contact your nearest authorized service center/ department. WARTUNG - GETRIEBE Das Getriebe wurde vom Werk abgedichtet und normalerweise sollte in Bezug auf die Flüssigkeit keine Wartung notwendig sein. Sollte das Getriebe undicht werden oder aus anderen Gründen Wartung benötigen, sollte die örtliche Vertragswerkstatt bzw.
6 WASCHANLAGEN-ÖFFNUNG DES SCHNEIDWERKS A Das Schneidwerk Ihres Traktors ist außen mit einer WaschanlagenÖffnung ausgestattet, die Teil der Waschanlage für das Schneidwerk ist. Sie sollte nach jedem Gebrauch verwendet werden. • Fahren Sie den Traktor auf eine ebene, saubere Stelle Ihres Rasens, möglichst nah an einen Wasserhahn, an den Sie Ihren Gartenschlauch anschließen können WICHTIG: Stellen Sie sicher, dass der Auswurfsammler des Traktors von Ihrem Haus, Ihrer Garage, geparkten Autos usw. weg zeigt.
6 BOCA DE LAVADO DE LA PLATAFORMA La plataforma del tractor cuenta con una boca de lavado en la superficie como parte del sistema de limpieza. Se debe utilizar tras cada uso. A B • Desplace el tractor a un punto nivelado y despejado del prado, cerca de un grifo al que pueda conectar la manguera. IMPORTANTE: Compruebe que el conducto de descarga del tractor queda orientado hacia OTRO PUNTO que no sea la casa, el garaje, coches aparcados, etc. Retire el depósito de polvo o de hojas si está fijado.
6 DEKREINIGINGSPOORT Het maaidek van uw trekker is aan de bovenkant uitgerust met een reinigingspoort als onderdeel van het dekreinigingssysteem. Dit systeem dient na elk gebruik van de maaier te worden gebruikt. • Rijd de trekker naar een vlakke, open plek op uw gazon, dicht genoeg bij een waterkraan om met de tuinslang te bereiken. BELANGRIJK: Zorg ervoor dat de uitworp van de trekker is weggericht van uw huis, garage, geparkeerde auto’s, enz. Verwijder de opvangbak of mulchplaat indien bevestigd.
7. Troubleshooting. 7. Störungssuche. Engine will not start 1. No fuel in fuel tank. 2. Plug defective. 3. Plug connection defective. 4. Dirt in carburetor or fuel pipe. Motor springt nicht an. 1. Kein Kraftstoff im Kraftstofftank. 2. Stopfen defekt. 3. Stopfenverbindung defekt. 4. Schmutz im Vergaser oder im Kraftstoffrohr. Start motor will not turn engine 1. Battery flat. 2. Poor contact between cable and battery pole. 3. Connection/disconnection level in wrong position. 4. Main fuse defective. 5.
7. Recherche des pannes. 7. Búsqueda de averías. Le moteur ne démarre pas 1. Manque de carburant dans le réservoir. 2. Bougie d'allumage défectueuse. 3. Le câblage de la bougie d'allumage défectueux. 4. Il y a des impuretés dans le carburateur ou dans le circuit du carburant. El motor no arranca 1. No hay combustible en el depósito. 2. La bujía es errónea. 3. La conexión de la bujía está defectuosa. 4. Hay suciedad en el carburador o en el tubo de combustible. Le démarreur n'entraîne pas le moteur 1.
7. Ricerca guasti. 7. Het localiseren van fouten. Il motore non parte 1. Manca il carburante. 2. Difetto di candela. 3. Collegamento della candela difettoso. 4. Sporco nel sistema di alimentazione e o nel carburatore. De motor start niet 1. Er is geen benzine in de tank. 2. De bougie is defect. 3. De bougie-aansluiting is defect. 4. Vuil in carburateur of brandstofleiding. Il motorino di avviamento non fa girare il motore 1. Batteria scarica. 2. Difetto di contatto tra cavo e polo della batteria. 3.
8. Storage. 8. Aufbewahrung. 8. Remisage. 8. Conservación. The following steps should be taken when mowing season is over: • Clean the entire machine, especially underneath the cutting unit cover. Do not use high pressure washer for cleaning. Water can enter engine and transmission and shorten the useful life of the machine. • Touch up all chipped paint surfaces in order to avoid corrosion. • Change engine oil. • Drain the fuel tank. Start the engine and allow it to run until it is out of fuel.
8. Rismessaggio. 8. Stallen. Al termine della stagione effettuare i seguenti interventi: • Pulire tutto il tagliaerba e particolarmente sotto il coperchio della falciatrice. Per le operazioni di pulizia, non utilizzare acqua ad alta pressione. L’acqua può infiltrarsi nel motore e nel sistema di trasmissione, riducendo quindi così il tempo di vita della macchina. • Ritoccare danni alla verniciatura per evitare ossidazione. • Cambiare l’olio del motore. • Vuotare il serbatoio della benzina.
12.01.17 JSE Printed in U.S.A.