Operation Manual

4
S Make sure the chain willnot make contact
with any object while starting the engine.
Never try to start the saw when the guide
bar is in a cut.
S Do notput pressureon thesaw at the endof
the cut. Applying pressure can cause you to
lose control when the cut is completed and
may cause serious personal injury .
S Stop the engine before setting the saw
down.
S Do not operate a chain saw that is dam-
aged, improperly adjusted, or not com-
pletely a nd securely assembled. Always
replace bar, chain, hand guard, or chain
brakeimmediately ifit becomesdamaged,
broken or is otherwise removed.
S With the engine stopped, hand carry the
chain sawwiththe muffleraway from your
body , and the guide bar and chain to the
rear, preferably covered with a scabbard.
CHAIN SAW SAFETY EQUIPMENT
NOTE:
In this section, the safety features of
the chain saw and their function are explained.
For inspection and maintenance, see instruc-
tio n s in the CHECKI NG, MAI NTAINING AND
SERVICING CHAIN SAW SAFETY EQUIP-
MENT section. See instructions under the
WHAT IS WHAT? section, to find where these
parts are located on your chain saw. The life
span of the machinecan bereducedandthe
risk of accidents can increase if machine
maintenance is not carriedout correctly and
if service and/or repairs are not carried out
professionally. If you need further informa-
tion, please contact your nearest service
dealer.
S Chain brake. Your chain saw is equipped
with achain brakethat is designed to stop
the chain from moving.
WARNING: The chain brake is de-
signed to stop the chain immediately if you
get akickback.The chainbrakereducesthe
risk of accidents, but only you can prevent
them.DONOTASSUMETHATTHECHAIN
BRAKE WILL PROTECT YOU IN THE
EVENT OF A KICKBACK.
S Throttle trigger lock--out. The throttle
lock--out is designed to prevent accidental
operation of the throttle trigger .
S Chain catcher. The chain catcher is de-
signed to catch the saw chain if it breaks.
S Vibration damping system. Your chain
saw is equipped with a vibration damping
systemthatis designed to minimizevibra-
tion and make operation easier.
SAFETY NOTICE:Exposure to vibrations
through prolonged use of gasoline powered
hand tools could cause blood vessel or nerve
damageinthe fingers,hands,andjoints ofpeo-
ple prone to circulation disorders or abnormal
swellings. Prolonged use in cold weather has
been linked to blood vessel damage in other-
wise healthy people. If symptoms occur such
as numbness, pain, loss of strength, change in
skincolor or texture, or loss of feeling in the fin-
gers, hands, or joints, discontinue the use of
this tool and seek medical attention. An anti-
vibrationsystemdoes not guaranteetheavoid-
ance of these problems. Users who operate
power tools on a continual and regular basis
must monitor closely their physical condition
and the condition of this tool.
S ON/STOP switch. The ON/STOP switch
should be used to stop the engine.
CHECKIN G, MAINTAINI NG AND
SERV I CI NG CHAIN SAW SAFETY
EQUIPMENT
WARNING: Never use a chain saw
with defective safety equipment. Safety
equipment must be inspected and main-
tained. If your chain saw does not pass in-
spection, take the saw to you r nearest ser-
vice dealer for repair .
S Chain brake. Brush off any wood dust,
resin and dirt from the chain brake and
clutch drum. Dirt and wear can impair op-
eration of the brake. For additional infor-
mation, see OPERATING YOUR UNIT
section.
S Throttletriggerlock--out. Checkthatthe
throttletriggercannotbeoperateduntilthe
throttle lock--out is pressed.
S Chain catcher. Check that the chain
catcher is not damaged and is firmly at-
tached to the body of the chain saw.
S Vibration damping system. Regularly
check the vibration damping units for
cracks or deformation. Make sure the
vibration damping units are securely at-
tached to the engine unit and handle unit.
S ON/STOP switch. Start the engine and
make sure the engine stops when you
move the ON/STOP switch to the ST OP
position.
MAINTAIN YOUR SAW IN GOOD
WORKING ORDER
S Have all chain saw service performed by a
qualified service dealer with the exception of
the items listed in themaintenancesectionof
this manual. For example, if improper tools
are used to remove or hold the flywhe el
when servicingtheclutch, structuraldamage
to the flywheel can occur and cause the fly-
wheel to burst.
S Make certain th e saw chain stops moving
when the throttle trigger is released. For
correction, refer to CARBURETOR AD-
JUSTMENTS.
S Never modify your saw in any way. Use
only attachments supplied or specifically
recom mend ed by the manufacturer.
S Keepthehandles dry,clean, andfree of oil
or fuel mixture.
S Keep fuel and oil caps, screws, and fas-
teners securely tightened.
S Use only McCulloch accessories and re-
placement parts as recommended.
HANDLE FUEL WITH CA UTION
S Do not smoke while handling fuel or while
operating the saw.
S Eliminate all sources of sparks or flam e in
the areas where fuel is mixed or poured.
Thereshouldbenosmoking,openflames,
orworkthatcouldcausesparks. Allowen-
gine to cool before refueling.