Operation Manual
3.15.1 Change PIN code
Enter the new PIN code and press
OK
. Enter the same
code again and confirm by pressing
OK
. When the PIN
code is changed, the message
PIN code changed
appears in the display.
Make a note of the new PIN code on the designated line
on the
MEMO
. See
Introduction on page 3
3.15.2 Security level
There are 3 security levels to choose from.
Security level
Low
Medium
High
Low
and
Medium
security prohibits access to the robotic
lawnmower if the PIN code is unknown.
High
security
also includes a warning that beeps if the correct PIN
code is not entered after a designated time period.
If the wrong PIN code is entered 5 times in succession
the robotic lawnmower is blocked for a time. The
blockage time is extended for every new incorrect
attempt.
Function
Low Medium High
Time lock X X X
PIN request X X
Alarm X
3.15.2.1 Time lock
This function means that the robotic lawnmower cannot
be started after 30 days without first entering the correct
PIN code. When the 30 days has passed the robotic
lawnmower will continue to mow as normal, but the
Enter PIN code
message appears when the hatch is
opened. Enter your code again and press
OK
.
3.15.2.2 PIN request
This function means that the robotic lawnmower
requests a PIN code when the main switch is set to
1
and each time the hatch is opened. The correct PIN
code must be entered to use the robotic lawnmower.
If the wrong PIN code is entered 5 times in succession
the robotic lawnmower is blocked for a time. The
blockage time is extended for every new incorrect
attempt.
3.15.2.3 Alarm
This function means that an alarm sounds if the PIN
code is not entered within 10 seconds after the STOP
button has been pressed or the robotic lawnmower has
been lifted up for any reason. A ticking noise indicates
that the PIN code must be entered to prevent triggering
the alarm. The alarm can be turned off at any time by
entering the correct PIN code.
3.15.3 New loop signal
The loop signal is randomly selected to create a unique
link between the robotic lawnmower and the charging
station. In rare cases, there may be a need to generate
a new signal, for instance if two adjacent installations
have a very similar signal.
1. Place the robotic lawnmower in the charging station.
2. Select
New loop signal
in the menu.
3. Press
OK
and await confirmation that the loop signal
has been generated. This normally takes about 10
seconds.
3.16 Settings
SETTINGS
ECO mode
Time & Date
Language
Country
Remote start (R600 only)
Calibrate guide (R600 only)
Reset user settings
About
3.16.1 ECO mode
This function automatically turns off the loop signal in
the boundary loop, the guide wires and the charging
station when the robotic lawnmower is not mowing, i.e.
when the lawnmower is charging or is not allowed to
mow due to timer settings.
The
ECO mode
is suitable to use where there is other
wireless equipment not compatible with the robotic
lawnmower e.g.certain hearing loops or garage doors.
When
ECO mode
is activated, the indicator lamp in the
charging station flashes green.
ECO mode
means that
the robotic lawnmower can only be started in the
charging station and not out in the working area.
In
ECO mode
, it is very important to always press the
STOP button before removing the robotic lawnmower
from the charging station. It is otherwise not possible to
start the robotic lawnmower. If the lawnmower has been
removed by mistake without first pressing the STOP
button, the lawnmower must be placed back in the
charging station and the STOP button pressed. Only
then can the robotic lawnmower be started inside the
working area.
Select
RUN ECO mode
and press
OK
to activate
ECO
mode
.
Note: Always press the STOP button before removing
the robotic lawnmower from the charging station. In
358 - 001 - 21.09.2017 Installation - 25