OPENconnectors Command Line Interace User Manual
CLI Commands
show
2
2-73
2XWSXW([DPSOH The output from the show.nameServer command displays as follows.
Type Port Id Port Name Node Name COS FC4 Types 
---- ------- ----------------------- ----------------------- --- --------- 
N 010400 00:11:22:33:44:55:66:77 20:11:22:33:44:55:66:77 2,3 2  
N 010500 00:11:22:33:44:55:66:78 20:11:22:33:44:55:66:78 2,3 0  
N 010600 00:11:22:33:44:55:66:79 20:11:22:33:44:55:66:79 2,3 2  
N 010700 00:11:22:33:44:55:66:80 20:11:22:33:44:55:66:80 2 2  
N 010800 00:11:22:33:44:55:66:81 20:11:22:33:44:55:66:81 3 2  
N 010900 00:11:22:33:44:55:66:82 20:11:22:33:44:55:66:82 3 2  
N 010C00 00:11:22:33:44:55:66:83 20:11:22:33:44:55:66:83 2,3 2  
N 010D00 00:11:22:33:44:55:66:84 20:11:22:33:44:55:66:84 2,3 2  
N 010E00 00:11:22:33:44:55:66:85 20:11:22:33:44:55:66:85 2 5  
N 010F00 00:11:22:33:44:55:66:86 20:11:22:33:44:55:66:86 2 4  
N 011200 00:11:22:33:44:55:66:87 20:11:22:33:44:55:66:87 2,3 2  
N 011300 00:11:22:33:44:55:66:88 10:11:22:33:44:55:66:88 2,3 2  
FC4 Types 
0: ISO/IEC 8802-2 LLC 
1: ISO/IEC 8802-2 LLC/SNAP 
2: SCSI-FCP 
3: SCSI-GPP 
4: IPI-3 Master 
5: IPI-3 Slave 
6: IPI-3 Peer 
7: CP IPI-3 Master 
8: CP IPI-3 Slave 
9: CP IPI-3 Peer 
10: SBCCS-Channel 
11: SBCCS-Control Unit 
12: FC-SB-2 Channel to Control Unit 
13: FC-SB-2 Control Unit to Channel 
14: Fibre Channel Service 
15: FC-FG 
16: FC-SW 
17: FC-AL 
18: SNMP 
19: HIPPI-FP 
20: Vendor Unique 
VKRZQDPH6HUYHU([W
6\QWD[ nameServerExt 
3XUSRVH This command displays extended information from the name server 
database for devices attached to this switch. The command provides 
Symbolic Nameserver information, as well as the same information 
as the show.nameServer command. Multiple devices per port are 
possible for any public loop device attached to an FL Port.
Because it contains symbolic nameserver information that can be lengthy, the 
CLI output wraps several times per node. For this reason, this command is 
supported only in comma-delimited mode. 
3DUDPHWHUV This command has no parameters. 
&RPPDQG([DPSOH Root> show nameServerExt










