ORIGINAL INSTRUCTION MANUAL McGregor 350W/450W/600W Grass Trimmer 7589940/7495065/7497173 (Model: MET3525/MET4530/MET6032) Important - Please read these instructions fully before starting assembly These instructions contain important information that will help you get the best from your grass trimmer, ensuring it is assembled correctly and safely.
Contents Safety information……………………………………………………….................................……….……........3 In the box………………………………………………………………….......................................…………….7 Assemble…………………………………………………………………...................................……………….. 8 Prepare.......................................................................................................................................................9 Operate......................................................................................
Safety information Important - Please read these instructions fully before starting assembly Warning symbols The following warning symbols appear throughout this assembly manual and indicate the appropriate safety measures you should take when assembling and operating the grass trimmer. This symbol indicates there is a danger of serious personal injury or death if you do not observe the warning.
Safety information Important - Please read these instructions fully before starting assembly Personal safety WARNING! Only operate the grass trimmer if you are wearing the correct Personal Protective Equipment (PPE) as described in the following warnings. Warning symbols The following warning symbols appear throughout this assembly manual and indicate the appropriate safety measures you should take when assembling and operating the grass trimmer.
Safety information Important - Please read these instructions fully before starting assembly General safety WARNING! Read all safety warnings and all instructions. Failure to follow the warnings and instructions may result in electric shock, fire and/or serious injury. Save all warnings and instructions for future reference. If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or similarly qualified persons in order to avoid a hazard.
Safety information Important - Please read these instructions fully before starting assembly General safety cord is damaged or worn. b) keep extension cords away from moving hazardous parts to avoid damages to the cords which can lead to contact with live parts. c) Before use, always visually inspect the machine for damaged, missing or misplaced guards or shields. d) Never operate the machine while people, especially children, or pets are nearby. 3.
In the box Parts 1 On/Off switch 11 Handle rotation locking button 2 Front handle 12 Cable holder 3 Front handle locking knob 13 Main handle 4 Height adjustment locking collar 14 Spool head cover 5 Aluminum tube 15 Line feed button 6 Motor housing 16 Cap release latch (on both sides) 7 Flower guard 17 Cutting line 8 Spool head Line cutter 9 Safety guard 18 19 Lower cable holder 20 Instruction manual 10 Cable 1 19 13 12 2 4 3 11 20 5 18 6 10 14 15 16 17 7 8
Assemble Assembling instructions Always take care when removing the packaging to prevent damage to you or to the grass trimmer. IMPORTANT! Before assembling the grass trimmer, check all the parts indicated in the manual are in the box. Inspect all the parts for signs of damage. Do not assemble the grass trimmer if you observe any damaged components. NOTE: Before using the tool, read the instruction book carefully.
Assemble Assembling instructions 2. REMOVING THE BLADE PROTECT LABEL (See Fig. B) The blade is covered with a protect label. Please remove it before operation. B Prepare Preparing instructions 2. ADJUST THE HEIGHT (See Fig. C1, C2) 1) Unscrew the height adjustment locking collar in the direction indicated to unlock, turn it clockwise. 2) Adjust the length of the Aluminum tube to the most comfortable length. 3) Tighten the locking collar in the direction indicated to lock, turn it counterclockwise.
Prepare Preparing instructions 3. ADJUSTING THE CUTTING ANGLE WARNING: Always disconnect the trimmer before making adjustments! 1) Put one foot on the motor housing portion of the trimmer head, then grip the main handle and apply adequate force on the main handle pushing it downwards, as shown in Fig. E1. 2) Adjust the main handle angle upwards, put one foot on the safety guard area of the trimmer head, then grip the main handle, apply adequate force to adjust, as shown in Fig. E2. E1 E2 4.
Prepare Preparing instructions 6. ON/OFF SWITCH To start, press and hold the switch. (See Fig. H) Release the switch to stop. WARNING: The cutting head continues to rotate after the trimmer has been switched off, wait until it has stopped then lay down the tool. H 7. CABLE STORAGE (SEE FIG. I1, I2) To release the cable, just turn down the upper cable holder (Fig. I2).
Operate Operating instructions WARNING: Always wear eye protection. Never lean over the trimmer head. Rocks or debris can ricochet or be thrown into eyes and face and cause blindness or other serious injury. When operating unit, check for the following: Wear eye protection and heavy clothing. Hold front handle with one hand and auxiliary handle with the other hand. Keep unit below waist level. Work only from your right to your left to ensure debris is thrown away from you.
Operate Operating instructions 2. EDGING Change the tool from trimming to edging mode 01: 1) Adjust the cutting angle to be in the lowest horizontal setting as shown in Fig. K1. 2) Push the handle rotation locking button downward and rotate the main handle clockwise at 90 degree(Fig. K2, K3). K1 K2 2 1 K3 Change the tool from trimming to edging mode 02: 1) Adjust the cutting angle to 30 degree to 50 degree as shown in Fig. K4.
Operate Operating instructions 3. AUTOMATIC LINE FEED SYSTEM When initially switching on the trimmer, a small length of line is fed out. A ‘clattering’ noise will be heard when the lines hit the line cutter. DO NOT BE ALARMED, this is quite normal. After about 5 seconds the line will be cut to the correct length and the noise will reduce as the motor receives full speed. If the noise of the line being cut can’t be heard, more line will be fed out.
Operate Operating instructions 6. WHEN REFITTING THE SPOOL CAP. Keep all areas of the cap and spool holder clean. Refit the cap, pressing firmly down towards the spool holder to ensure cap is fully located. Check that the cap is correctly fitted by trying to remove it without depressing the two latches. 7. TO REPLACE CUT LINE. For your convenience it is recommended you buy spool and line complete. --TO FIT SPOOL AND LINE COMPLETE: 1) Remove old spool. 2) Place new spool into cutting head.
Maintenance Maintenance Remove the plug from the socket before carrying out any adjustment, servicing or maintenance. Your power tool requires no additional lubrication or maintenance. There are no user serviceable parts in your power tool. Never use water or chemical cleaners to clean your power tool. Wipe clean with a dry cloth. Always store your power tool in a dry place. Keep the motor ventilation slots clean. Keep all working controls free of dust.
Technical data Technical data table Model MET3525 Voltage Power input No load speed Cutting width 350W 25cm 600W 9500/min 30cm 32cm 1.65mm 2*3m Protection class Machine weight MET6032 450W 10500/min Diameter of line Line length MET4530 230-240V~50/60Hz 2*5m /II 2.0kg 2.6kg 2.8kg Noise and technical date MET3525: A weighted sound pressure LpA = 78dB(A) KpA=3 dB (A) LwA = 93.6dB(A) A weighted sound power MET4530: A weighted sound pressure LpA = 78dB(A) KpA=3 dB (A) LwA = 93.
Accessories MET3525 MET4530 Safety guard 1 Flower guard 1 MET6032 We recommend that you purchase your accessories from the same store that sold you the tool. Choose the type according to the work you intend to undertake. Refer to the accessory packaging for further details. Store personnel can assist you and offer advice. Troubleshooting General troubleshooting The following chart lists problem symptoms, possible causes and corrective action, if your electric grass trimmer does not operate properly.
Getting help Customer helpline 0345 605 2065 Guarantee Dear Customer, In the unlikely event that your device develops a fault, please contact our Customer service department on the telephone number shown below. 1. These guarantee terms cover additional guarantee rights and do not affect your statutory warranty rights. Claims must be accompanied by Proof of Purchase.
