Owner`s manual

23
Figure 7
Figure 6
The following listings indicate the Setup Menu Mode (Con-
troller or Preamp), Menu Name, Default Setting and the
page number for instructions on how to change a setting.
Default Settings
Menu Function Name Setting Page No.
Control Version (C1000 Firmware) _ . _ _ 23
Control Display (Brightness) 7 23
Control Remote (Control) HRO61 24
Control Meter (Illumination) ON 24
Control Volume (Display) Percent 24
Control Trigger A Lvl (Rear Panel Jack) 5V 24
Control Trigger B Lvl (Rear Panel Jack) 5V 25
Control Triamp (Balanced Outputs) OFF 25
Control D/A Ctrl (MDA1000) OFF 25
Preamp Input 3 (Title of Inputs) TUN 26
Preamp D Port (Assignment to Input) Note 2 27
Preamp Trim (Input Source Level) 0.0 27
Preamp Trigger (Input Source) -- 28
Preamp ACC Control (Remote Con.) -- 29
Preamp LPROC (Listen Processor) NONE 30
Preamp RPROC (Record Processor) NONE 31
Preamp MM (Phono Capacitance) 50PF 32
Preamp MC (Phono Resistance) 25 OHM 32
Preamp Passthru (Multichannel) OFF 32
3. Rotate the BALANCE (Menu) Control and notice that
the Setup Controller Setup Mode advances through
seven different possible adjustment selections and one
informational display.
Note: When in SETUP MODE, it may be necessary to
rotate the Controls (BALANCE, RECORD and
LISTEN) either clockwise or counter-clockwise to
the desired function or setting.
4. Press the SETUP Push-button to exit the CONTROL-
LER Menu, the LED above the SETUP Push-button
will extinguish and the Front Panel Display will revert
back to its normal display. Refer to figure 3.
5. Now Press the SETUP Push-button twice to enter the
PREAMP Setup Menu. Refer to figure 6.
6. Rotate the BALANCE (Menu) Control and notice that
the Setup Preamp Mode advances through nine different
possible adjustment selections.
7. To exit from the Setup Preamp Mode press the SETUP
Push-button, the LED above the SETUP Push-button
will extinguish and the Front Panel Display will revert
back to its normal display. Refer to figure 3a or 3b.
Display Brightness
The Front Panel Alphanumeric DISPLAY Brightness may
be varied from a setting of 1 (Dim) to 7 (Bright). Follow the
steps below for reducing the Display Brightness.
1. Press the SETUP Push-button once to access the Setup
Controller Mode unless the C1000C is already in the
Setup Controller Mode.
2. Rotate the BALANCE (Menu) Control until the word
“DISPLAY 7” appears. Refer to figure 8.
3. Rotate the LISTEN (Select) Control until the Front
Panel Alphanumeric Display indicates “DISPLAY 5”
or the desired Brightness is achived. Refer to figure 9.
4. If no other adjustments are to be made at this time,
press the SETUP Push-button to exit the Setup Control-
ler Mode or proceed to the next desired Setup Control-
ler Mode for adjustment.
Figure 9
Firmware Version
The C1000 functionality is controlled by internal software
that is know as Firmware. The Version of the Firmware in
the C1000 can be identified at any time by utilizing the
Setup Controller Mode.
1. Press the SETUP Push-button once to access the Setup
Controller Mode.
2. Rotate the BALANCE (Menu) Control until VERSION
1.0 or higher appears. Refer to figure 7.
3. The number after the character V is the Firmware num-
ber.
4. If no other adjustments are to be made at this time,
press the SETUP Push-button to exit the Setup Control-
ler Mode or proceed to the next desired Setup Control-
ler Mode for adjustment.
Figure 8
Notes: 1. Charts on page 33 allow for recording any
changes made to the default settings.
2. The D. Port default assignment is the same as the
C1000 Controller Rear Panel Data Port Labeling.
Setup