Owner`s manual

11
How to Operate
How to Operate
Power On
The Red LED located above the word “STEREO-
PHONIC” nomenclature on the Front Panel lights to
indicate the C22 is connected to an active AC Outlet.
To Switch On the C22, momentarily press downward
the POWER Rocker Switch on the Front Panel or
the appropriate Power Push-button on the Remote
Control. During the Tube Warm Up time (when first
switched ON), the Front Panel INPUT and MODE SE-
LECTOR LEDs will flash and the Audio Outputs will
be muted. Refer to illustration on the previous page
and figure 1 on this page.
Source Selection
Select the desired source using the INPUT SELEC-
TOR Control on the Front Panel or press the INPUT
▲ or ▼ on the Remote Control.
Volume Control
Rotate the Front Panel VOLUME Control or use the
VOLume ▲ (Up) or ▼ (Down) Push-buttons on the
Remote Control for the desired listening level.
Loudness Compensation
To activate the Loudness Compensation Circuitry
place the LOUDNESS Rocker Switch in the IN Posi-
tion on the Front Panel. When active, the Loudness
Compensation Circuitry works in conjunction with the
rotational position of the Volume Control. It com-
pensates for the sensitivity of the human ear at softer
listening levels by boosting the volume level of the
low frequencies relative to the midrange frequencies
to provide a fuller sound.
Balance Control
Rotate the Front Panel BALANCE Control as needed
to achieve approximately equal listening volume levels
in each Loudspeaker. Rotate the BALANCE counter-
clockwise to emphasize the Left Channel by reducing
the level of the Right Channel. Rotate the BALANCE
clockwise to emphasize the Right Channel by reduc-
ing the level of the Left Channel.
Mode Selector
The Front Panel MODE SELECTOR Control allows
the Left and Right Input Signals from the desired
source to be combined into various different outputs
sent to the Loudspeakers and Headphones. Refer to
the chart below:
Output Channels
Mode
Selection
LEFT RIGHT
STEREO
Left Input Signal Right Input Signal
STEREO
REV
Right Input Signal Left Input Signal
MONO
Left + Right Input Signals Left + Right Input Signals
L to L&R
Left Input Signal Left Input Signal
R to L&R
Right Input Signal Right Input Signal
L+R to L
Left +Right Input Signals -
L+R to R
- Left+ Right Input Signals
Bass Control
Rotate the BASS clockwise from the center (12
o’clock) position to emphasize the low frequency con-
tent of the music. Likewise rotate the BASS counter-
clockwise from the center position to de-emphasize
the low frequency content of the music.
Treble Control
Rotate the TREBLE clockwise from the center (12
o’clock) position to emphasize the high frequency con-
tent of the music. Likewise rotate the TREBLE coun-
terclockwise from the center position
to de-emphasize the high frequency
content of the music.
Tone Bypass Switch
When the TONE Switch on the Front
Panel is placed in the BYPASS posi-
tion the Tone Controls together with
the Tone Circuitry is totally bypassed
for a flat response.
Record Monitor
To activate the Record Monitor
Circuit place the RECORD Rocker
Switch in the MONITOR Position
on the Front Panel. When active, the
sound coming from Record Source
Component will be heard. Some Re-
cording Components allow for listen-
ing to the Playback Signal a fraction
of a second after the recording has
taken place.
Output 1 and 2
To switch Off the audio signal going
to the Power Amplifiers connected to
the C22 Preamplifier Outputs, place
the OUTput 1 and/or the OUTput 2
Rocker Switch in the OFF Position on the Front Panel.
When there is a Power Control Connection between
the C22 Power Control OUT 1 or OUT 2 and the
Power Amplifier(s), the Power Amplifier(s) will be
switched Off.
Phono Load Adjustments
There are Phono Load Adjustments for both types of
Figure 1