Owner's Manual

9
Rear Panel Connections and Connecting Components
port Power Control Out Jack to the Tuner Power
Control In Jack.
5. Connect a Control Cable from the Tuner Power
&RQWURO2XW-DFNWRWKH0HGLD%ULGJH3ZU&WUO
3RZHU&RQWURO,Q-DFN
6. Connect a Control Cable from the C47 POWER
&21752/75,*7ULJJHU-DFNWRWKH3RZHU
Amplifier Power Control In Jack.
Notes: 1. If two separate Power Amplifiers are used
(Left and Right Channels), connect the Power
Control Output of the first Amplifier to the
Power Control Input on the second Amplifier.
2. By the defaut settings, POWER CONTROL
Triggers 1 and 2 will be active when the C47
OUTPUT 1 and/or 2 is selected by the Front
Panel or Remote Control Push-buttons.
7. Optionally, connect a Control Cable from the C47
32:(5&21752/75,*7ULJJHU-DFNWR
WKH3RZHU$PSOLILHU6HFRQGDU\5RRP3RZHU
Control In Jack.
8. Connect any additional Components in a similar
manner, as outlined in steps 1 thru 5.
Data Control Connections:
9. Connect a Control Cable from the C47 DATA
32576-DFNWRWKH781(5'DWD,Q-DFN
Note: To have source components (e.g. Tuner) respond
only to their specific “Function Commands”
issued by the Remote Control, it is first neces-
sary change the Data Ports Default settings for
the “Tuner” Input. Refer to Setup “Data Port
Assignment”on page 16.
10. Connect a Control Cable from the C47 CD DATA
3257-DFNWRWKH6$&'&'7UDQVSRUW'DWD,Q
Jack.
11. Connect a Control Cable from the C47 DATA
3257-DFNWRWKH0HGLD%ULGJH'DWD,Q-DFN
&RQQHFWDQ\DGGLWLRQDO0F,QWRVK&RPSRQHQWVLQD
similar manner, as outlined in steps 9 thru 11.
Sensor Connection:
13. Connect a Control Cable from the C47 IR Input
&RQQHFWRUWRWKHH[WHUQDO6HQVRU)RUDGGLWLRQDO
information, refer to “General Information” note 8
on page 4.
Audio Connections:
&RQQHFWDQ$XGLR&DEOHIURPWKH&81%$/-
$1&(',13877XQHU-DFNVWRWKH7XQHU
Unbalanced Output Jacks.
15. Using the “DIN Cable-Twisted Pair” cable (sup-
SOLHGZLWKD0&77UDQVSRUWIURPWKH&0&7
',*,7$/$8',2,1387FRQQHFWRUWRWKH6$&'
CD Transport DIN Output connector.
&RQQHFWDQ;/5$XGLR&DEOHIURPWKH&%$/-
$1&(',1387FRQQHFWRUVWRWKH0HGLD%ULGJH
Balanced Output connectors.
17. Connect a Digital Coaxial Cable from the C47
',*,7$/$8',2,1387&2$;,$/-DFNWRWKH
Digital Audio Player Digital Coax Output Jack.
18. Connect the Audio Cables coming from the Turn-
WDEOHWRWKH&0&3+212,1387-DFNV
Note: If the Turntable has a Moving Magnet Car-
tridge, connect the audio cables to the C47
MM PHONO INPUT instead of the MC Input.
&RQQHFW;/5$XGLR&DEOHVIURPWKH&%$/-
DQFHG287387FRQQHFWRUV/HIWDQG5LJKWWR
WKH3RZHU$PSOLILHUV3ULPDU\5RRP%DODQFHG
/HIWDQG5LJKW,QSXWV
2SWLRQDOO\FRQQHFW;/5$XGLR&DEOHVIURPWKH
&%$/DQFHG287387FRQQHFWRUV/HIWDQG
5LJKWWRWKH3RZHU$PSOLILHU6HFRQGDU\5RRP
%DODQFHG/HIWDQG5LJKW,QSXWV
&RQQHFWDQ\DGGLWLRQDO0F,QWRVK&RPSRQHQWVLQD
similar manner, as outlined in steps 14 thru 20.
2SWLRQDO³3DVV7KUX´&RQQHFWLRQV
&RQQHFW;/5$XGLR&DEOHVIURPWKH$93UR-
FHVVRU)URQW&KDQQHOV/HIWDQG5LJKW%DODQFHG
2XWSXWFRQQHFWRUVWRWKH&%$/$1&(',1-
PUT 2 connectors.
Note: Refer to Setup “PASSTHRU” on page 17 to acti-
vate the BALANCED 2 Input.
23. Connect a Control Cable from the C47
3$667+58-DFNWR$93URFHVVRU3RZHU&RQWURO
=RQH=$-DFN
Optional USB Connection:
&RQQHFWD86%FDEOHZLWKW\SH$WRW\SH%
FRQQHFWRUVIURPWKH&86%',*,7$/$8',2
,1387FRQQHFWRUWRDQDYDLODEOH86%FRQQHFWRU
on the computer.
*URXQG&RQQHFWLRQV
25. Connect the Ground Cable coming from the Turn-
table to the C47 PHONO INPUT GND Binding
Post.
AC Power Cord Connections:
26. Connect the C47 to a live AC Outlet using the sup-
SOLHG3RZHU6XSSO\&RUG