Owner’s Manual MSS530 and MSS630 Loudspeaker Systems MSS530 MSS630 McIntosh Laboratory, Inc.
Thank You Table of Contents Your decision to own this McIntosh MSS530 or MSS630 Loudspeaker System ranks you at the very top among discriminating music listeners. You now have “The Best.” The McIntosh dedication to “Quality,” is assurance that you will receive many years of musical enjoyment from this unit. Please take a short time to read the information in this manual. We want you to be as familiar as possible with all the features and functions of your new McIntosh. Thank You .........................
Safety Instructions IMPORTANT SAFETY INSTRUCTIONS! PLEASE READ THEM BEFORE OPERATING THIS EQUIPMENT. General: 1. Read all the safety and operating instructions, contained in this owner’s manual, before operating this equipment. 2. Retain this owner’s manual for future reference about safety and operating instructions. 3. Adhere to all warnings and operating instructions. 4. Follow all operating and use instructions. 5.
Introduction The McIntosh Woofer/Midrange and Tweeter Drivers offer extremely smooth frequency response, low distortion, high sensitivity and high power handling capability. When these Drivers are combined with other McIntosh Vehicle Components, you will enjoy sonically accurate music reproduction in your vehicle which meets McIntosh traditional standards of excellence. Top View of the MN530 and MN630 Crossover Networks 2.7" 6.
Introduction, Performance Features and Overall Dimensions Front View of the MS20 Tweeter Driver Side View of the MS20 Tweeter Driver Rear View of the MS20 Tweeter Driver 2.13" 0.88" 1.8" 5.4cm 2.24cm 4.55cm Side View of the MS530 Woofer/Midrange Driver Front View of the MS530 Woofer/Midrange Driver 5.4" 13.59cm 2.9" 7.37cm 6.1" 15.49cm Front View of the MS630 Woofer/Midrange Driver 6.3" 15.9cm Side View of the MS630 Woofer/Midrange Driver 3.25" 8.26cm 7.2" 18.
Installation It is recommended that a qualified professional install all McIntosh Sound System Products. McIntosh Woofer/ Midrange Drivers, Tweeters and Crossover Networks should be used in conjunction with McIntosh Subwoofers and McIntosh Electronics to achieve the best possible performance. McIntosh Subwoofers are designed to operate in the bass frequency range below 120Hz and need not be physically close to Midrange and Tweeter Loudspeakers in order to maintain good imaging and system frequency balance.
Installation Mounting the Crossover When selecting a Crossover mounting location, make sure there is adequate room for ventilation (there are openings on both sides of the CrossMounting Screw Locations over) and for making connections to it. Use the supplied screws for mounting the Crossover to the vehicle. 1. Using the Crossover as a template, mark the two locations to drill holes in the mounting surface for the Crossover mounting screws. Drill two holes with an appropriate size drill bit.
How to Connect a Two Way System How to Connect a Two Way System 1. Press the connector ends of the supplied Woofer/ Midrange Red/Black cables onto the matching Woofer/ Midrange connecting lugs. 2. Attach the other ends of the two Red/Black Woofer/ Midrange cables to the Crossover Network WOOFER OUTPUT Terminals. The Black wire connects to a MINUS (-) Terminal and the Red wire to a PLUS (+) Terminal. 3.
How to Connect a Three Way System How to Connect a Three Way System 1. Press the connector ends of the supplied Woofer/ Midrange Red/Black cables onto the matching Woofer/ Midrange connecting lugs. 2. Attach the other ends of the two Red/Black Woofer/ Midrange cables to the Crossover Network WOOFER OUTPUT terminals. The Black wire connects to a MINUS (-) Terminal and the Red wire to a PLUS (+) Terminal. 3.
Specifications MSS530 System Specifications MSS630 System Specifications System Parameters Peak Power Continuous Power (EIA + H.P.) Frequency Response System Sensitivity1 Nominal Impedance (Znom) Crossover Frequency Low Pass Slope High Pass Slope 120 Watts 60 Watts 80 Hz - 20kHz 85 dB 4 Ohms 2400 Hz 12 db/oct 12 db/oct System Parameters Peak Power Continuous Power (EIA + H.P.
Packing Instructions Packing Instructions In the event it is necessary to repack the equipment for shipment, the equipment must be packed exactly as shown below. Use the original shipping carton and interior parts only if they are all in good serviceable condition. If a shipping carton or any of the interior part(s) are needed, please call or write Customer Service Repair Department of McIntosh Laboratory.
McIntosh Laboratory, Inc. 2 Chambers Street Binghamton, NY 13903 McIntosh Part No.