Owners Manual LS360 Loudspeaker System LS360 McIntosh Laboratory, Inc.
WARNING - TO REDUCE RISK OF FIRE OR ELECTRICAL SHOCK, DO NOT EXPOSE THIS EQUIPMENT TO RAIN OR MOISTURE. NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED PERSONNEL. IMPORTANT SAFETY INSTRUCTIONS! PLEASE READ THEM BEFORE OPERATING THIS EQUIPMENT. General: 1. Read these instructions. 2. Keep these instructions. 3. Heed all warnings. 4. Follow all instructions. 5. Warning: To reduce risk of fire or electrical shock, do not expose this equipment to rain or moisture.
Thank You Table of Contents Your decision to own this McIntosh LS360 Loudspeaker System ranks you at the very top among discriminating music listeners. You now have The Best. The McIntosh dedication to Quality, is assurance that you will receive many years of musical enjoyment from this unit. Please take a short time to read the information in this manual. We want you to be as familiar as possible with all the features and functions of your new McIntosh. Safety Instructions ..........................
Introduction and Performance Features Introduction The McIntosh LS360 Loudspeaker System is designed for Home Theater and Music Reproduction. It is a three-way system with two 10 inch LD/HP1 woofers, one 8 inch LD/ HP midrange and five 1 inch dome tweeters. The LS360 is designed to work as a Left or Right (Main) Loudspeaker in a Music System, or as a Main or Surround Loudspeaker in a Home Theater System.
Dimensions LS360 Dimensions The following dimensions can assist in determining the best location for your LS360 Loudspeaker System. There is additional information on the next page pertaining to installing the LS360 into cabinets.
Dimensions Side View of LS360 with Grille 6 Side View of LS360 with Grille Removed
Installation Installation Optional Feet Two sets of optional feet (four Tiptoes and four Glides) are supplied with the LS360 Loudspeaker System. To prevent crushing carpet use the Tiptoe spikes; to protect non-carpeted flooring use the chrome Glides. Both the Glides and Tiptoes have a threaded shaft and locking nut that screw into the tapped holes in the bottom of the LS360s base rails. The feet can be independently adjusted to compensate for uneven flooring or to aim the loudspeakers upward or downward.
How to Connect How to Connect The McIntosh LS360 Loudspeaker System utilizes binding posts for speaker wire connections. Refer to figure 3. 1. Connect a loudspeaker cable from the black (negative ) loudspeaker binding post to the negative or common output terminal of one channel of the amplifier. 2. Connect a loudspeaker cable from the red (positive + ) loudspeaker binding post to the positive or 4 ohm output terminal of the same channel of the amplifier. 3.
Front and Rear Views Five 1 inch Tweeter Array 8 inch LD/HP Midrange 10 inch LD/HP Woofers Ports Connecting Terminals - + 9
Specifications Specifications Driver Complement Two 10 inch Woofers 8 inch Midrange Five 1 inch Dome Tweeters Impedance 4 ohms Nominal Frequency Response 29Hz - 20kHz + 2dB (Anechoic Response) Sensitivity 88dB (2.8V/1m) Crossover Frequencies 1.5kHz 200Hz Power Handling 600 Watts Maximum Dimensions 49-1/4 inches (125.09cm) Height, 13-1/2 inches (33.75cm) Width, 17-1/2 inches (44.
Packing Instructions Packing Instructions In the event it is necessary to repack the equipment for shipment, the equipment must be packed exactly as received. Failure to do this will result in shipping damage. Use the original shipping carton and interior parts only if they are all in good serviceable condition. If a shipping carton or any of the interior part(s) are needed, please call or write Customer Service Department of McIntosh Laboratory.
McIntosh Laboratory, Inc. 2 Chambers Street Binghamton, NY 13903 McIntosh Part No.
