McIntosh Laboratory, Inc. 2 Chambers Street Binghamton, New York XR50 Loudspeaker System Owner’s Manual 13903-2699 Phone: 607-723-3512 www.mcintoshlabs.
WARNING - TO REDUCE RISK OF FIRE OR ELECTRICAL SHOCK, DO NOT EXPOSE THIS EQUIPMENT TO RAIN OR MOISTURE. NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED PERSONNEL. To prevent the risk of electric shock, do not remove cover or back. No user-serviceable parts inside. IMPORTANT SAFETY INSTRUCTIONS! PLEASE READ THEM BEFORE OPERATING THIS EQUIPMENT. 1. Read these instructions. 2. Keep these instructions. 3. Heed all warnings. 4. Follow all instructions. 5. Do not use this apparatus near water. 6.
Thank You Your decision to own this McIntosh XR50 Loudspeaker System ranks you at the very top among discriminating music listeners.. You now have “The Best.” The McIntosh dedication to “Quality,” is assurance that you will receive many years of listening enjoyment from this unit. Please take a short time to read the information in this manual. We want you to be as familiar as possible with all the features and functions of your new McIntosh.
Introduction McIntosh Acoustic Engineers have achieved in the design of the XR50 Loudspeaker System, a level of high performance. The XR50 provides superior spaciousness sound reproduction with unusual sound stage depth in a full range system. The XR50 utilizes a three-quarter inch Titanium Dome Tweeter and 2 two inch Midrange Inverted Titanium Dome Drivers. Refer to figures 1 and 2.
Connector/Cable Information, Introduction and Performance Features Performance Features • Patented LD/HP® Technology The McIntosh Low Frequency Loudspeaker Elements feature the patented LD/HP Magnetic Circuit Design. This design, when compared to conventional Loudspeaker Drivers, reduces distortion significantly. It also increases power handling and efficiency. The rear vent through the magnetic assembly offers improved heat dissipation.
Dimensions The following dimensions can assist in determining the best location for your XR50. Rear View of the XR50 Loudspeaker System Side View of the XR50 Loudspeaker System Front View of the XR50 Loudspeaker System 8" 9-7/8" 20.3cm 11-3/4" 29.9cm 6-1/2" 16.5cm 25.0cm 16-1/2" 42.0cm 17" 43.0cm 12-5/8" 32.0cm 7/8" 2.2cm 5-1/2" 13.8cm 5/8" 1.8cm 2" 5.1cm 4" 10.2cm 6" 15.
Dimensions Front View of the XR50 Loudspeaker System Top End View of the XR50 Loudspeaker System 6-1/2" 16.5cm Bottom End View of the XR50 Loudspeaker System When mounting the XR50 to a Loudspeaker Stand use machine screws (1/4 inch, 20 threads per inch) with a length going into the XR50 not to exceed 0.4 inches 14-7/8" 37.8cm 9-7/8" 25.0cm 13" 33.1cm 4-1/2" 11.4cm 11-1/4" 28.6cm 8" 20.3cm 6-1/4" 16.0cm 1-1/2" 3.8cm 5" 12.7cm 1-1/2" 3.8cm 4" 10.
Unpacking the Loudspeaker Installation To protect the fine finish of the XR50 Loudspeaker System during the installation process, it is advisable to prepare a suitable area. A freshly vacuumed carpeted area covered with a soft, clean fabric, such as a large bed linen or blanket would be suitable. It is recommended that the Professionals at your McIntosh Dealer, who are skilled in all aspects of installation and operation, install the XR50 Loudspeaker System and any associated audio equipment. 1.
Unpacking the Loudspeaker and Installation Locating Loudspeakers for use in Home Theater In a Home Theater application, the placement of Left and Right Front Loudspeakers can be limited by such considerations as the size and location of the video monitor. The locating suggestions in the “for use in a Music System” section can still be helpful as a starting place. Refer to figure 9.
Input Terminals When connecting the Loudspeaker Hookup Cables to the XR50 Loudspeaker Input Terminals please follow the steps below: 1. Rotate the end of the Input Terminal Post counterclockwise until an opening appears. Refer to figures A and B. 2. Insert the Loudspeaker hookup Opening cable into the Input Terminal Figure B Figure A Post opening or the cable spade lug around the center post of the Input Terminal. Refer to figure C. 3.
How to Connect Spade Lug or Wire Connections: 11. Referring to the illustration on the next page, connect the Loudspeaker hookup cables to the XR50 Negative (-) Input Terminal and Positive (+) Input Terminal. Insert the spade lug connector or prepared section of the cable end Figure 15 Figure 16 into the terminal side access hole, and tighten the terminal cap until the cable is firmly clamped into the terminals so the lugs or wire cannot slip out. Refer to figures 15 and 16.
Photos 13
Specifications Specifications General Specifications System Driver Complement One 6 inch Woofer (incorporating LD/HP1) Two 2 inch Titanium Inverted Dome Midranges One 3/4 inch Titanium Dome Tweeter Enclosure Finish Available in various real wood veneers with a high gloss polyester finish Impedance 8 ohms Nominal Frequency Response 40Hz - 45,000Hz Sensitivity 81dB (2.
Packing Instructions Packing Instructions In the event it is necessary to repack the equipment for shipment, the equipment must be packed exactly as shown below. To protect the finish of the Loudspeaker it is advisable to wrap the Loudspeaker Cabinet with a durable plastic film. Then place wraped Loudspeaker into the protective fiber cover, before inserting it into the shipping carton. Use the original shipping carton and interior parts only if they are all in good serviceable condition.
McIntosh Laboratory, Inc. 2 Chambers Street Binghamton, NY 13903 www.mcintoshlabs.com The continuous improvement of its products is the policy of McIntosh Laboratory Incorporated who reserve the right to improve design without notice. Printed in the U.S.A. McIntosh Part No.