D.I.
WARNING: FOR YOUR OWN SAFETY, PLEASE FOLLOW THE INSTRUCTIONS IN THE MANUAL CLOSELY, AS FAILURE TO DO SO MAY RESULT IN PERSONAL INJURY! Before you proceed, please read the following safety precautions: As the elasticity is very strong on arms, please tie arms together when assembling awning. Do not stand face front of awning when cutting off binds between arms. Hold tightly and stretch slowly until completely open.
K D-4 J I G H F-1 Parts Diagram D-1 D-3 D-2 A-1 T B-1 A-1.Roller(left) A-2.Roller(right) A-3.Roller connector A-A-1.Bolt M4 x 15 B-1.Torsion bar(left) B-2.Torsion bar(right) B-3.Torsion bar connector B-B-1.Bolt M6 x 45 B-B-2.Bolt M6 + Washer Ø6 C-1.Front bar(left) C-2.Front bar(right) S M L-1 R N O P B-B-1 A-A-1 B-B-2 J C-1 C-3.Front bar link tube D-1.Left roller support D-2.Bolt M10 x 60 D-3.Gear box D-4.Bolt M6 x 50 E-1.Right roller support E-2.Round shaft cover F-1.
Steps of Assembly 1. Roller Assembly: Insert roller connector (A-3) into right roller (A-2), fasten it with bolt (A-A-1). Link the left roller (A-1) to the connector (A-3), fasten it with bolt (A-A-1). Now you have a full length roller. A-1 A- A-3 A-A-1 2. Front bar assembly: Insert front bar connector (C-3) into right front bar (C-2), fasten with bolt (A-A-1). Link left front bar (C-1) with the connector (C-3), fasten it with bolt (A-A-1). Now you have a full length front bar. C-1 C-3 C-2 A-A- 3.
. Spread out both of the fabrics (M) and valance (O) and insert fabric liner {Three fabric liner: (N-1 Thin liner x1 )and (N-2 Thick liner x2 )}. Push the thin one end of fabric with liner inserted into gauges on roller, then put the thick one end through front bar and put another thick one into valance. (Attention: The fabric has two sides: front and back. The back side is with hem facing downwards) See below image. M O 6.
(E-1) and link it with round shaft of right side using hammer, tighten screw on it using screwdriver. 8. Setting position of whole awning: Make sure two arms are tied tightly to torsion bar, move front bar wrist support (Q-1) until it connects with front bar wrist. Align the front bar and roller, tighten bolt (Q-2) of two front bar wrist support upwardly by screwdriver. Then fasten self locking nut M10 (a) with bolts up to 95% tight using ribbon tube spanner.
Specification Product name Retractable awning (Please see details on the package) Material and surface treatment Materials: Steel tube, Aluminum alloy, plastic parts, polyester fabric. Service treatment : tubes: spray paint and oxidation Cloth surface: PU, UV, waterproof Applicable wall type Reinforced concrete walls, brick walls, and wooden walls Recommende d installation height 2.5m ~ 3.5m Applicable weather The products are used to shield sunshine. Applicable when wind is under level 5.
Parts List Please prepare the following tools before installation (not included with the product) Awning Instructions Hand Crank Wall Bracket 8 Product model No. Of wall brackets No. Of expansion bolts < 3m 2 4 3.5m ~ 4.
Installation Procedure 1. Measure the distance along the wall where it can be placed. Drill holes for wall brackets on the wall according to the installation distances and height of the wall brackets. The diameter and depth of hole must be the same as expansion bolts. The holes of each group must be on the same line in transversal direction and vertical direction. 3.5 Inch (Note: It is recommended to draw lines on the wall first to ensure precise position and size of the holes) 2.
Installation distance between wall brackets Awning < 3m Only 2 wall brackets for each end of torsion bars Awning 3.5m ~ 4.5m 2 wall brackets at each end of torsion bar, a middle bracket in between distance of 2 arm shoulders (arm brackets refer to steps of assembly 6) Awning > 5m 2 wall brackets at each end of torsion bar, 2 middle brackets divide into equal length in between distance of 2 arm shoulders at each end of torsion bars. (steps of assembly 6) 4.
6. Instruction for front side leveling Loosen the locking nuts. 2 Turn the jack bolt to adjust pitch 3 Adjust the arm until the front side stays in horizontal line. 4 Tighten the locking nuts. 1 Common Mistakes FAQ: What if the fabric wraps unevenly or the two arms cannot open together at the same time? Answer: Look at the stability of two arms and adjust the front bar wrist of the faster arm outwards accordingly.
