Specifications

.ror 1I1::1U WSUUlauUU Ul 11I1 C:JCC\OC nc:aacr au" LUI1UW we
instructions below:
a.
Removing screws as required, open heater access door
and detach adjacent power entry panel.
Remove wires to unit contactor (Ill, 11.2, lL3) ftom the
unit terminal block on the left side of the electric heat
compartment Remove and discard the terminal block
. and the adjacent ground l';1g.
Remove the heater kit block-off panel and install the
heaterkitin itspla~ using9 ofthe 12screwspreviously
removed.
b.
c.
d.
Connect the unit contactor wires (Ill, IL2, IL3) to the
compressor fuse block on the heater kit
Re-install the power entty panel & ~n con(Juit and the
proper size field w.iringthrough the opening in the panel.
\
ColUlectfield wiring to the power tenninal block located
on the electric heater kit Connect ground wire to the
adjacent ground lug.
e.
f.
g. Connect heater kit control plug to the receptacleon the
controlwiringharness.
h. Check all electrical connections including factory wiring
within the unit and make sure all connections are tigh
and properly located.
i. -- Close heater access door and secure. With tbe screws
previously removed.
t AffiHeatel'-kit-wiring4iagmm-m-inside-()k6ntro1--1filtcr
accessdoor.
------.
I. AU lOWvOltage wanng mUStoe roUted mto the lOWvOltage
connection area and not into the power wiring or heater conCroI
area.
2. For thermostat low voltage connections, see unit installation
Instructions.
3. Thennostat heat anticipator should be adjustable for a
minimumrangeof .10 - 1.20. Typicalsettingsare as follows:
THERMOSTAT HEAT ANTICIPATORSETTlNG*
NUMBER OF STAGES
I Z
SE'ITlNG .7 .7&."
*NOTES
I. Nonnally.1hc firststage heathas a fixed$CUing.
2. Some chcrmostaIs have DOll!iustable second stage heat antidpator
setting indicator. Follow the instnlctions in these spc:cific
lhennostaU 10 get proper operation.
3. RqJlace the control box cover and control compartmentacccss panel
after all wiring is complctccl.
4. Chcclcunit for properopcwlon.
WIRE SIZE -7SOCINSULA110N FOR 1% VOLTAGE DROP
.
COPPERWIRE-AWG'MCM
SUPPLY
CIRCUIT
SUPPLYWIRELENG1H FEET
AMPACITY
100 ISO
200 250 300
15
10
8 6 6 6
:20
I
" ..
..
..
25
8 6
.. 4
3
30 6
4 4
3 2
35 6
4
3 2
I
40 6 4 3 2 I
45 4
3 2 I
VO
SO 4
3
2'
I
I/O
60 4
2
I
I/O 210
70
3 2 110
210 310
80 3
1 110 210
3/0
90 2 110 210
3/0 .c/O
100 2 I/O 210
3/0 .uo
110
I 210 310 <C/O
250
12S I 210 3/0 ...,0 250
150 110
310 410 250
300
175
2/0
410
250
300 350
200
3/0 410
300
350
400
225 'I/O
250
350
450
500
Page 47