Instruction Manual ® 8", 10", 12", 14", 16" LX200 R Advanced Ritchey-Chrétien Telescopes with GPS and AutoStar II Hand Controller ® (800) 626-3233 www.meade.
WARNING! Never use a Meade LX200R™ Telescope to look at the Sun! Looking at or near the Sun will cause instant and irreversible damage to your eye. Eye damage is often painless, so there is no warning to the observer that damage has occurred until it is too late. Do not point the telescope at or near the Sun. Do not look through the telescope or SmartFinder™ as it is moving. Children should always have adult supervision while observing.
CONTENTS WARNING! Quick-Start Guide .......................................................... 4 Telescope Features ...................................................... 6 AutoStar II Features ...................................................... 9 Getting Started ..............................................................12 Parts Listing ..............................................................12 How to Attach the Tripod to the Telescope ..............12 How to Assemble Your Telescope ..........
QUICK-START GUIDE It is recommended that you attach the supplied tripod to the LX200R for observing. Perform the telescope and AutoStar II setup indoors in the light so that you become familiar with the parts and operation before moving the telescope outside into the dark for observing. The setup is the same for the standard field tripod and the giant field tripod. Remove the spreader bar (see above figure) from the shipping carton. Slide the spreader bar onto the threaded rod.
ON/OFF 7. R.A. Lock HBX Port Press the computer control panel power switch to OFF, if necessary. Remove the AutoStar II handbox and the AutoStar II coil cord from the packing materials. Plug one end into the HBX port of the telescope's computer control panel and plug the other end into the coil cord port on the AutoStar II handbox. OR Attach microfocuser: Remove the dust cap from the rear cell port (A) of the telescope (Note: Telescope not shown for clarity).
TELESCOPE FEATURES 2@ 2! 2% 2) 1( 1* (not shown, on left fork arm) 2# (not shown) 2$ B c d e 1& 1^ 1% 1$ f g h i j 1) AutoStar II Hand Controller. See page 9. 1! 1@ 1# Fig. 1: The LX200R Telescope; Computer Control Panel (inset); AutoStar II Handbox (inset). -6- Looking at or near the Sun will cause irreversible damage to your eye. Do not point this telescope at or near the Sun. Do not look through the telescope as it is moving.
LX200R: YOUR PERSONAL WINDOW TO THE UNIVERSE Caution: Using products other than standard Meade accessories may cause damage to the telescope’s internal electronics and may void the Meade warranty. B Want to learn more about the eyepieces available for your LX200R telescope? See OPTIONAL ACCESSORIES, pages 43, 44, and 45.
Definitions Throughout this manual, you will notice the terms "Alt/Az," "Right Ascension," and "Declination." Alt/Az or more properly, altazimuth, is frequently used to refer to altitude or Declination (the up-and-down vertical movement of the telescope) and azimuth or Right Ascension (the side-to-side horizontal movement of the telescope). Right Ascension is abbreviated as "R.A." and Declination Important Note: After the telescope is aligned (see page 18), the Dec.
AUTOSTAR II FEATURES Fig. 2: The AutoStar II Handbox. Tour the Cosmos with Just the Push of a Button Control of the LX200R telescope models is through the operation of the standard AutoStar II system. Nearly all functions of the telescope are accomplished with just a few pushes of AutoStar II’s buttons. Want to learn more about downloading the latest updates of AutoStar II software from the Meade website? See page 3o.
The AutoStar II system provides control of virtually every telescope function. The AutoStar II handbox has soft-touch keys designed to have a positive feel. The LCD (Liquid Crystal Display) is backlit with red LEDs (Light Emitting Diodes) for easy viewing in the dark. The backlit display, key arrangement, and sequential menu structure make AutoStar II extremely user friendly. B c d e Want to learn more e about using the GO TO function? See page 20.
5 SS: Press to display the Solar System library. 6 STAR: Press to display the Star library. 7 RET (Reticle): Press to display the Reticle Control menu. 8 IC: Press to display the Index Catalog library. 9 NGC (New General Catalog): Press to display the NGC catalog library. 0 LIGHT: Press to turn on and off the red utility light on the top of the hand-box. RET 7 Want to learn more about the Reticle menu? See page 31. h Scroll Keys: Press to access options within a selected menu.
GETTING STARTED Parts Listing Getting the telescope ready for first observations requires only a few minutes. When first opening the packing box, note carefully the following parts: LX200R Telescope with fork mount system AutoStar II handbox and interface coil cord; handbox holder Microfocuser assembly 8 x 50mm viewfinder assembly Eyepiece holder and 1.25" diagonal prism ( 8", and 10" models) 1.
Caution: Use care to install batteries as indicated by the battery compartment. Follow battery manufacturer's precautions. Do not install batteries backwards or mix new and used batteries. Do not mix battery types. If these precautions are not followed, batteries may explode, catch fire, or leak. Improperly installed batteries void your Meade warranty. Always remove the batteries if they are not to be used for a long period of time.
4. 5. Groove Note: The AutoStar II handbox and the microfocuser do not require batteries; the telescope supplies their power. Attach microfocuser: Remove the dust cap from the rear cell port (5, Fig. 1) of the telescope. Thread the microfocuser adapter (B, Fig. 6) onto the rear cell port thread. Slide the microfocuser (C, Fig. 6) over the microfocuser adapter and tighten the three hex screws (K, Fig. 6) using the provided hex key. Attach Diagonal (or accessories) 1.
Mounting Slot Track Thumbscrews Fig. 11: Viewfinder Assembly. Collimation Screws Viewfinder Eyepiece GPS Receiver with a lower power eyepiece such as the 26mm Plössl. When the object is located and centered in the eyepiece, you may wish to switch to a higher power eyepiece to enlarge the image as much as practical for prevailing seeing conditions. For information about optional eyepieces for the your telescope, see OPTIONAL ACCESSORIES, page 43.
OBSERVING Important Note: Objects appear upsidedown and reversed left-forright when observed in the viewfinder. Objects viewed through the telescope eyepiece when inserted into the diagonal prism and microfocuser assembly appear right-side-up, but reversed left-for-right. This image inversion is of no consequence when observing astronomical objects and, in fact, all astronomical telescopes yield inverted images.
9. Bring the object into focus (see below). Focusing the Eyepiece Using the Microfocuser See MIRROR MIRROR, page 38, for more information about the microfocuser and the primary mirror lock. The LX200R zero image-shift microfocuser (24, Fig. 1) allows you to obtain the most precise image focus possible during visual, photographic, and CCD applications, maintaining precise and "jiggle-free" image centering on even the smallest CCD chips. To use the microfocuser: 1.
Observe the Moon Definition: Initialization is a procedure that ensures that AutoStar II operates correctly. When you first use AutoStar II, it doesn't yet know where the observation location site is or the time or date of the observation session. During the automatic alignment procedure, the system calculates these parameters automatically.
5. Important Note: Once the telescope is aligned, only use the Arrow keys to move the telescope. Once the telescope has been aligned, do not loosen the telescope locks (12 and 17, Fig. 1), or move the base manually, or alignment will be lost. Important Notes: It is recommended that you do not attempt a GPS fix indoors. It is also recommended that you CALIBRATE SENSORS the first time your telescope takes a GPS fix. See page 29 for more information. "Automatic Alignment" displays.
Tip: The GO TO key also allows you to perform a "spiral search." A spiral search is useful when the telescope slews to an object, but that object is not visible in the eyepiece after the telescope finishes its search. (This sometimes occurs during an alignment procedure.) Press GO TO when the telescope stops slewing. The telescope begins to move in a spiral pattern at a very slow speed around the search area.
5. Press MODE to return to the Tour list. Press the Scroll keys to scroll through the list. Press ENTER when you find the next object you wish to observe. 6. Press and hold down MODE for two seconds to leave the Guided Tour menu. Other Guided Tours are available, such as "How Far is Far" and "A Star's Life." If you have programming skills, you may wish to create a custom Guided Tour. See CREATE YOUR OWN GUIDED TOUR, page 58.
BASIC AUTOSTAR II SETUP MENU Automatic alignment permits all telescope operations with only minimal setup. Select Item: Object Select Item: Setup UTILITIES MENU Calculate eyepiece magnifications; set timer alerts; create your own landmark survey. The Universe of Autostar II Select Item: Utilities GLOSSARY What is an elliptical galaxy? How far away is the Sun? Expand your knowledge of astronomy by displaying terms and definitions, and other information.
4. Press the Scroll Down key once to display the "Sunset" option in the Event menu. 5. Press the ENTER key to choose the "Sunset" option and move down another level. 6. AutoStar II calculates the Sunset time based on the current date, time, and location. AutoStar II then displays the results of the calculation. 7. Press MODE once to start moving back up through the AutoStar II levels. The first level up is the Event menu. 8. Press MODE again to move up another level.
- 24 - Looking at or near the Sun will cause irreversible damage to your eye. Do not point this telescope at or near the Sun. Do not look through the telescope as it is moving. Sunrise Sun Transit Sunset Moonrise Moon Transit Moonset Moon Phases Next Full Moon Next New Moon Next 1st Qtr Next 3rd Qtr Meteor Showers Quadrantids Lyrids Etc. Solar Eclipses Lunar Eclipses Min.
Object Menu Almost all observing with AutoStar II is performed using the Object menu category. (Note: Exceptions include Guided Tour and Landmark Survey.) See GO TO SATURN, page 20, for an example of observing using the Object menu. Also see USING THE GUIDED TOUR, page 20. AutoStar II contains many libraries of viewable objects, such as stars, planets, comets, nebulae and so forth.
Identify: An exciting feature for an observer who wants to scan the night sky and start exploring. After the telescope has been properly aligned, use the AutoStar II Arrow keys to move about in the sky. Then follow this procedure: Important Note: Only use the Arrow keys to move the telescope during the Identify procedure. Do not loosen the telescope locks or move the base or alignment is lost. Want to learn more about using the Browse menu? See page 35. 1.
Glossary Menu The Glossary menu provides an alphabetical listing of definitions and descriptions for common astronomical terms and AutoStar II functions. Access directly through the Glossary menu or through hypertext words embedded in AutoStar II. A hypertext word is any word in [brackets], usually found when using the AutoStar II Help function or when reading a scrolling message such as a description of a planet or star.
Sleep Scope: A power saving option that shuts down AutoStar II and the telescope without forgetting its alignment. With "Sleep Scope" selected, press ENTER to activate the Sleep function. AutoStar II goes dark, but the internal clock keeps running. Press any key, except ENTER, to re-activate AutoStar II and the telescope. Park Scope: Designed for a telescope that is not moved between observing sessions. Align the telescope one time, then use this function to park the telescope.
Note: Custom Tracking Rate allows you to enter values from -999 (stands for 99.9%) to 999 (stand for +99.9%). The lower the number, the slower the rate; the higher the number the faster the rate. If you enter -999, the telescope will move so slow as to appear to be stopped. If you enter 999, the telescope will be moving at approximately twice the tracking rate. - 29 - (Note that it does not prevent you from performing a manual slew past this limit.
Reverse U/D: Reverses the functions of the Up and Down Arrow keys for controlling the telescope's motion (i.e., the Up key moves the telescope down). Home Sensors: Turns off or on the True North and True Level sensors, if preferred, for Easy, One-Star, and Two-Star alignment. User must then manually level the telescope and point the telescope to True North during alignment. Default setting is "On.
All: Everything—user-defined information and AutoStar II software—is sent to another AutoStar II. Download: Transfers information from a personal computer or another AutoStar II. During the operation, the warning “Downloading Do Not Turn Off” appears. Catalogs: Receives only user-defined object information, such as new satellite orbits or comet data to another AutoStar II handbox. Software: Receives only the basic AutoStar II software.
ADVANCED AUTOSTAR II FEATURES Before trying out the examples in this section, familiarize yourself with the basic operations of AutoStar II described earlier in this manual. The following examples assume that you have a basic knowledge of AutoStar II and understand how to scroll to a desired menu or menu option, and how to enter numbers and text. It also assumes that you have initialized and aligned your telescope.
11. Press MODE. "Site: Edit" displays. 12. Using the Arrow keys, scroll to "Site: Select." The site you have just edited displays. Press ENTER to select the site. Creating User Objects In this procedure, you will enter coordinates of celestial objects that do not appear in any of the AutoStar II libraries. You will enter the object's name and R.A. and Dec. coordinates (required information). You may also enter the object's magnitude and size (optional information).
Observing Satellites In this procedure, you will prepare your telescope to observe a satellite pass. 1. Navigate to the "Object: Satellite" menu option and press ENTER. 2. Use the Scroll keys to scroll through the list of satellites. 3. Select a satellite from the list and press ENTER. 4. "Calculating...." and then "Tracking..." displays. If the satellite is going to make a pass, "Located" displays. 5. Use the Scroll keys to display data about the pass: aos—acquisition of signal and los—loss of signal.
those in the Landmark database. Be sure to change this option back to "Astronomical" when you wish to view celestial objects again. 3. Press MODE once. "Select Item: Setup" displays. 4. Press the Scroll Down key once and "Select Item: Object" displays. Press ENTER. "Object: Solar System" displays. 5. Press the Scroll Up key twice and "Object: Landmarks" displays. Press ENTER. "Landmark: Select" displays. 6. Press the Scroll Down key once. "Landmark: Add" displays. Press ENTER. 7.
In this procedure, you will center an object you wish to have identified by AutoStar II in the telescope eyepiece and use the "Identify" menu to find out information about the object or the nearest object to it in the AutoStar II database. 1. Center the object you wish to have identified in the telescope's eyepiece. 2. Navigate to the "Object: Identify" option and press ENTER. 3. "Searching..." displays. When AutoStar II finishes calculating, the name of the closest object displays. 4.
Important Note: If you disable the automatic alignment/GPS function and then use the alternate alignments described in this section, you will be prompted to enter the Time, Date, and Daylight Savings status. Alternate Alt/Az Alignments If you would rather set up your telescope without using automatic alignment, AutoStar II offers alternative alignment methods for both alt/az and equatorial mounting.
Two-Star Alt/Az Alignment Two-Star Alignment requires some knowledge of the night sky. AutoStar II provides a library of bright stars and two stars from this library are chosen by the observer for alignment. In this procedure, AutoStar II does not automatically find home, level, or North. 1. Select Alignment. Select "Align: Two Star" from the Setup menu. Press ENTER. Note: AutoStar II locates alignment stars based on the date, time, and location entered. The alignment stars may change from night to night.
Periodic Error Correction If you wish to perform high-precision astrophotography, you may wish to "train" your telescope in order to keep objects that you are imaging dead center in the telescope's mirror during the photographic exposure. Periodic error correction (PEC) helps to remove the slight perturbations from center that occur due to the mechanical nature of a telescope. To perform this procedure, you need to use a high-power reticle, such as the 9mm reticle (see OPTIONAL ACCESSORIES, page 44).
PHOTOGRAPHY You may perform through-the-telescope photography with any 35mm camera body with a removable lens. You may connect a camera to a #62 T-Adapter which is then connected to the microfocuser assembly. See Fig. 21. Using this method, the telescope effectively becomes the lens of the camera. 1 2 The #62 T-Adapter (1, Fig. 21) connects to the microfocuser assembly, followed by a T-Mount (2, Fig. 21) for the particular brand of 35mm camera being used, followed by the camera body (3, Fig. 21).
Photography with a Digital Camera Although digital cameras still cannot match the quality of images provided by traditional 35mm cameras, they provide some significant advantages to the casual astrophotographer: You do not have to develop the images (instant images), lower costs, computer and internet readiness. And because unwanted photos are easily discarded, they provide the freedom to experiment.
• Magic Eye software-assisted focusing. • Automatic and manual exposure control from .001 to 15 seconds (up to 450x longer than web cams). • Automatically takes multiple exposures. The AutoStar Suite Software includes powerful tools to help you get the most from your Meade LX200R telescope: • Sophisticated planetarium program with over 19 million objects. Fig. 25: Image of M13 captured with the Deep Sky Imager. • Select objects from the planetarium display and the telescope slews to those objects.
OPTIONAL ACCESSORIES A wide assortment of professional Meade accessories is available for the LX200R telescope models. The premium quality of these accessories is well-suited to the quality of the instrument itself. Consult the Meade General Catalog for complete details on these and other accessories. Meade Series 4000 Eyepieces: Eyepiece 7” f/15 Power/Actual Field 8” f/6.3 Power/Actual Field 10” f/6.3 Power/Actual Field Super Plössl Eyepieces (4-elements; 1.25” O.D., except as noted) 6.4mm 9.7mm 12.
Series 4000 8 - 24mm Zoom Eyepiece: The internal zoom optics of this eyepiece move on smooth, precisely machined surfaces which maintain optical collimation at all zoom settings. A scale graduated in 1mm units indicates the zoom focal length in operation. An excellent addition to any eyepiece set. #140 2x Barlow Lens: A 3-element design, doubles each eyepiece power while maintaining uncompromised image resolution, color correction, and contrast.
Piggyback Brackets: Piggyback photography is one of the most popular and easiest ways to get started in astrophotography. Attach your 35mm camera, with its own 35mm-to-250mm lens, atop your LX200R in equatorial mode, and guiding the camera through the main telescope, wide-field photos of the Milky Way of remarkable detail and clarity can be taken. Dew Shields: In moist climates, water particles suspended in the atmosphere may condense on the front surface of the telescope's correcting plate.
MAINTENANCE LX200R telescopes are precision optical instruments designed to yield a lifetime of rewarding applications. Given the care and respect due any precision instrument, your LX200R will rarely, if ever, require factory servicing. Maintenance guidelines include: a. Avoid cleaning the telescope’s optics: A little dust on the front surface of the telescope’s correcting lens causes virtually no degradation of image quality and should not be considered reason to clean the lens. b.
With the star or hot spot centered, de-focus the image. You will notice that the out of focus star image looks like a ring of light surrounding a dark central spot; the dark central spot is in fact the shadow of the secondary mirror. Turn the focus knob until the ring of light fills about 10% of the eyepiece field-diameter. If the dark central spot is offset in (i.e., not concentric with) the ring of light, your telescope’s optical system is misaligned and requires collimation. 1 2 3 Fig.
i. As a final check of alignment, examine the star image in focus with the higher power eyepiece as suggested (j), under good viewing conditions. The star point should appear as a small central dot (commonly referred to as an “Airy disc”) with a diffraction ring surrounding it. To give a final precision collimation, make extremely slight adjustments of the three set screws, if necessary, to center the Airy disc in the diffraction ring.
SPECIFICATIONS 8" f/10 LX200R Specifications Optical design ..............................................Advanced Ritchey-Chrétien telescope Clear aperture..............................................203mm (8") Focal length ................................................2000mm Focal ratio (photographic speed) ................f/10 Resolving power ..........................................0.56 arc sec Coatings ......................................................
12" f/10 LX200R Specifications Optical design ..............................................Advanced Ritchey-Chrétien telescope Clear aperture..............................................305mm (12") Focal length ................................................3048mm Focal ratio (photographic speed) ................f/10 Resolving power ..........................................0.375 arc sec Coatings ......................................................
16" f/10 LX200R Specifications Optical design ..............................................Advanced Ritchey-Chrétien telescope Clear aperture..............................................406.4mm (16") Focal length ................................................4064mm Focal ratio (photographic speed) ................f/10 Resolving power ..........................................0.28 arc sec Coatings ......................................................
APPENDIX A: EQUATORIAL (POLAR) ALIGNMENT Equatorial Alignment In equatorial (or "polar") Alignment, the telescope is oriented so that the horizontal and vertical axes of the telescope are lined up with the celestial coordinate system. Important Note: The "Telescope: Mount" option of the Setup menu is set to "Alt/Az" as the default mount by the factory.
Using setting circles requires a developed technique. When using the circles for the first time, try hopping from one bright star (the calibration star) to another bright star of known coordinates. Practice moving the telescope from one easy-tofind object to another. In this way, the precision required for accurate object location becomes evident. Note You may also enter an object's R.A. and Dec. coordinates using the "User: Objects" option of AutoStar II's Object menu.
Lining Up with the Celestial Pole Objects in the sky appear to revolve around the celestial pole. (Actually, celestial objects are essentially “fixed.” Their apparent motion is caused by the Earth’s rotation). During any 24 hour period, stars make one complete revolution about the pole, making concentric circles with the pole at the center.
ting circle and slightly loosen the two bolts located under the knob. Now turn the circle unit until it reads 89.2°, the Declination of Polaris. Then tighten down the two bolts and replace the knurled knob. Should you wish to use the manual setting circles, the R.A. setting circle (Fig. 40) must be calibrated manually on the Right Ascension of a star every time the telescope is set up. (The R.A.
AutoStar II Polar Alignment AutoStar II provides three different (manual) methods for polar alignment: Easy, OneStar and Two-Star. Important Note: In order to select any of AutoStar II's three polar alignment options, you must first select "Polar" in the "Mount" option of the "Setup: Telescope" menu. Easy Polar Alignment Two alignment stars are chosen by AutoStar II based on the date, time, and location. First, choose "Polar" from the "Setup: Telescope: Mount" menu.
APPENDIX B: LATITUDE CHART Latitude Chart for Major Cities of the World To aid in the polar alignment procedure (see page 54), latitudes of major cities around the world are listed below. To determine the latitude of an observing site not listed on the chart, locate the city closest to your site. Then follow the procedure below: Northern hemisphere observers (N): If the site is over 70 miles (110 km) North of the listed city, add one degree for every 70 miles.
APPENDIX C: CREATE YOUR OWN GUIDED TOUR Creating your own Guided Tour can be an extremely useful tool. You can preprogram a script of objects you wish to view and study on any given night. You can also create a viewing script for students or for a friend. More commands will be added from time-to-time to the list below. Periodically visit Meade's website (www.meade.com) for future additions.
TITLE IC PLANET COMET CONSTELLATION PICK ONE/PICK END TEXT SAO MOON LUNAR ECLIPSE STAR AUTO SLEW USER MESSIER SATELLITE METEOR SHOWER LANDMARK ON/OFF NGC CALDWELL ASTEROID DEEP SKY DEFINE #END Description String: Description of an object. Must be surrounded by quotation marks. If the description is longer than one line, each line must end with a quotation mark and a hard return. Begin the next description line with a quotation mark.
PLANET "name" Enter PLANET and then the name of the desired planet in quotes. AutoStar II provides the user with a description of the selected planet from its database. For example: PLANET "Pluto" MOON This command accesses information about the Moon from the AutoStar II database. SATELLITE "name" Enter SATELLITE and then the name of the desired satellite in quotes. AutoStar II displays information about the satellite from its database.
PICK ONE AUTO SELECT MESSIER 13 AUTO SELECT MESSIER 15 AUTO SELECT MESSIER 92 AUTO SELECT MESSIER 4 AUTO SELECT MESSIER 68 AUTO SELECT NGC 1234 AUTO SELECT TEXT "None Available" "I'm sorry. There are no bright globular" "clusters visible at this time." PICK END AUTO SLEW ON / AUTO SLEW OFF With AUTO SLEW ON enabled in the tour, AutoStar II automatically slews the telescope to objects first before displaying the text description.
APPENDIX D: TRAINING THE DRIVE Train the telescope motors using AutoStar II. Perform this procedure if you are experiencing any pointing accuracy problems. Fig. 41 depicts the complete Drive Training procedure. Note: Use a terrestrial object, such as a telephone pole or lamp post, to train the drive. Complete this exer- cise once every 3 to 6 months to maintain the highest level of telescope pointing accuracy. LX200R TIPS Further Study.... This manual gives only the briefest introduction to astronomy.
APPENDIX E: THE MOON MENU The Moon option of the Object menu allows you to observe the moon in a way never possible before. You will be able locate many specific features of the lunar surface, including hundreds of craters, mare, valleys, and mountains. One special feature allows you to view all six Apollo landing sites.
APPENDIX F: 16" LX200R FEATURES Figure 47: 16" LX200R Computer Control Panel. 16" LX200R Unique Features Caution: Due to the weight and size of the 14" and the 16" LX200R models, please use extreme caution whenever assembling, disassembling, lifting, transporting or storing this product. Two or more persons should always be used whenever performing any of the above tasks. Disregard for the above warning could result in serious injury or death.
B Caution: Next to the focus assembly are two red slot-head bolts, used only for safety reasons in shipment. Remove these bolts before attempting to turn the focus knob. In its place, insert the rubber plugs provided as a dust protector (these rubber plugs are included with your hardware package). c e f d The 16” LX200R should never be commercially shipped without the red bolts in place. This is essential during commercial transport, where rough handling may occur.
To collapse the tripod (after removing the telescope) for storage, follow these steps: a. Loosen the tension knob and rotate the spreader bar 60° from its assembled position, so that one spreader bar arm is located between each adjacent pair of tripod legs. b. Move the spreader bar to the top of the threaded rod. Tighten the tension knob, locking the bar. c. Working one leg at a time, gradually collapse the legs of the field tripod until the tension hub is positioned onto the threaded rod.
c. Lock the OTA in place using the four 3/8”-16x3/4” bolts. Thread up the four bolts into the bottom of the Dec. castings, two on each side. Using the supplied hex key, tighten to a firm feel only (Fig. 57). Attaching the Power and Data Cords Several power and data cords are supplied with the 16” LX200R. These should all be attached before powering up the telescope. a. Confirm that the power switch (A, Fig. 47) on the power panel is in the OFF position.
APPENDIX G: 14" LX200R FEATURES 14" LX200R Unique Features The 14" LX200R contains, for the most part, the same features (covered earlier in this manual) as all other LX200R telescope models. The following features are unique to the 14" model: Fig. 59a: One of the two 14" LX200R battery compartments (older models). Fig. 59b: An indentation on the underside of one of the 14" LX200R battery compartments (older models).
APPENDIX H: DE-ROTATER AND MICROFOCUSER ASSEMBLY When using a de-rotater, it is important to attach the microfocuser so that it is backed off slightly from the de-rotater. If the microfocuser is flush against the de-rotater, the assembly will not work properly. This is true also with other accessories that may attach up flush against the de-rotater housing. The diagonal mirror (if used without the microfocuser) may be attached tightly as it does not rub up against the de-rotater housing.
APPENDIX I: Smart Mount Introduction Smart Mount improves the pointing accuracy of your LX200R telescope's "Go to" sytem. Despite careful efforts to calibrate and align telescopes, they may fail to precisely center objects. Smart Mount allows your telescope to learn about, and then correct for, any systematic pointing errors, regardless of the cause.
Permanently Mounted Scopes For permanently mounted telescopes, it is not necessary to have more than one model unless the weight and balance of auxiliary equipment introduces balance or flexure changes that significantly affect pointing. The best practice is to train the Smart Mount and then run a couple of sessions with Update enabled. Thereafter, simply leave Smart Mount On as the installation default.
BASIC ASTRONOMY In the early 17th century Italian Scientist Galileo, using a telescope smaller than your LX200R, turned it skyward instead of looking at the distant trees and mountains. What he saw, and what he realized about what he saw, has forever changed the way mankind thinks about the universe.
Tip: Enter a date in the Date menu and you can determine if a planet(s) will be visible during the night of the entered date by checking its rise and set times. Planets Planets change positions in the sky as they orbit around the Sun. To locate the planets on a given day or month, consult a monthly astronomy magazine, such as Sky and Telescope or Astronomy. You can also consult AutoStar II for information about planets. Scroll to the "Object: Solar System" menu and scroll through the lists of planets.
MEADE LIMITED WARRANTY Every Meade telescope, spotting scope, and telescope accessory is warranted by Meade Instruments Corporation (“Meade”) to be free of defects in materials and workmanship for a period of ONE YEAR from the date of original purchase in the U.S.A. and Canada. Meade will repair or replace a product, or part thereof, found by Meade to be defective, provided the defective part is returned to Meade, freight-prepaid, with proof of purchase.