Datasheet

ManualsBrandsMEAN WELL ManualsIndoor Lighting AccessoriesLED driverLED-switching power supply

SPECIFICATION

MODEL CEN-100-20 CEN-100-24 CEN-100-30 CEN-100-36 CEN-100-54CEN-100-48

CEN-100-42

DC VOLTAGE

CURRENT RANGE

RATED POWER

OUTPUT

LINE REGULATION

LOAD REGULATION

SETUP TIME

VOLTAGE RANGE Note.4

FREQUENCY RANGE

POWER FACTOR (Typ.)

EFFICIENCY (Typ.)

AC CURRENT (Typ.)

INPUT

INRUSH CURRENT (Typ.)

LEAKAGE CURRENT

WORKING TEMP.

WORKING HUMIDITY

STORAGE TEMP., HUMIDITY

TEMP. COEFFICIENT

VIBRATION

MTBF

DIMENSIONOTHERS

NOTE

PACKING

OVER CURRENT

SHORT CIRCUIT

OVER VOLTAGE

OVER TEMPERATURE

20V 24V 30V 36V 54V48V

42V

0 ~ 4.8A 0 ~ 4A 0 ~ 3.2A 0 ~ 2.65A 0 ~ 1.77A0 ~ 2A

0 ~ 2.28A

96W 96W 96W 95.4W 95.58W96W

95.76W

2.0Vp-p 2.7Vp-p 3Vp-p 3.6Vp-p 5Vp-p4.6Vp-p

4Vp-p

±10%

±3.0%

±5.0%

90 ~ 295VAC 127 ~ 417VDC

47 ~ 63Hz

PF>0.97/115VAC, PF>0.95/230VAC, PF>0.92/277VAC at full load (Please refer to "Power Factor Characteristic" curve)

88% 89% 90% 90% 91%91%90%

22.8 ~ 26V 28 ~ 32V 34 ~ 38V 41 ~ 46V 59 ~ 68V

54 ~ 60V

47 ~ 52V

1.4A/115VAC 0.7A/230VAC 0.5A/277VAC

COLD START 45A(twidth=85 s measured at 50% Ipeak) at 230VACμ

<0.75mA / 240VAC

95 ~ 110%

Protection type : Constant current limiting, recovers automatically after fault condition is removed

Hiccup mode, recovers automatically after fault condition is removed

-30 ~ +70℃ (Refer to "Derating Curve")

20 ~ 95% RH non-condensing

-40 ~ +80 , 10 ~ 95% RH℃

± ℃ ℃0.03%/ (0 ~ 50 )

10 ~ 500Hz, 5G 12min./1cycle, period for 72min. each along X, Y, Z axes

519.5Khrs min. MIL-HDBK-217F (25 )℃

195*62.5*40.5mm (L*W*H)

1. All parameters NOT specially mentioned are measured at 230VAC input, rated load and 25℃ of ambient temperature.

2. Ripple & noise are measured at 20MHz of bandwidth by using a 12" twisted pair-wire terminated with a 0.1uf & 47uf parallel capacitor.

3. Tolerance : includes set up tolerance, line regulation and load regulation.

4. Derating may be needed under low input voltage. Please check the static characteristics for more details.

5. Please refer to "DRIVING METHODS OF LED MODULE".

6. The power supply is considered as a component that will be operated in combination with final equipment. Since EMC performance will be affected by the

complete installation, the final equipment manufacturers must re-qualify EMC Directive on the complete installation again.

7. Direct connecting to LEDs is suggested, but is not suitable for using additional drivers.

8. To fulfill requirements of the latest ErP regulation for lighting fixtures, this LED power supply can only be used behind a switch without permanently

connected to the mains.

Protection type : Shut down o/p voltage, re-power on to recover

RIPPLE & NOISE (max.) Note.2

VOLTAGE TOLERANCE Note.3

ENVIRONMENT

SAFETY &

EMC

PROTECTION

Shut down o/p voltage, re-power on to recover

WITHSTAND VOLTAGE

ISOLATION RESISTANCE

I/P-O/P:3.75KVAC I/P-FG:2KVAC O/P-FG:0.5KVAC

UL8750, CSA C22.2 No. 250.0-08(except for 48V, 54V), TUV EN61347-1, EN61347-2-13, IP66, J61347-1, J61347-2-13 approved

I/P-O/P, I/P-FG, O/P-FG: >100M Ohms / 500VDC / 25℃/ 70% RH

SAFETY STANDARDS

Compliance to EN55015, EN61000-3-2 Class C (≧65% load) ; EN61000-3-3

Compliance to EN61000-4-2,3,4,5,6,8,11, EN55024, EN61547, light industry level (surge 4KV), criteria B

13 ~ 20V 15.6 ~ 24V 19.5 ~ 30V 23.4 ~ 36V 35.1 ~ 54V31.2 ~ 48V

27.3 ~ 42V

RATED CURRENT 4.8A 4A 3.2A 2.65A 1.77A2A

2.28A

17 ~ 22V 22 ~ 27V 27 ~ 33V 33 ~ 40V 49 ~ 58V43 ~ 53V

37 ~ 46V

VOLTAGE ADJ. RANGE (SVR1)

CURRENT ADJ. RANGE(SVR2)

3.12 ~ 4.8A

2.6 ~ 4A

2.08 ~ 3.2A

1.72 ~ 2.65A

1.15 ~ 1.77A1.3 ~ 2A

1.48 ~ 2.28A

File Name:CEN-100-SPEC 2014-03-13

100W Single Output LED Power Supply

CEN-100 series

‧Universal AC input / Full range (up to 295VAC)

‧Protections: Short circuit / Over current / Over voltage / Over temperature

‧Output voltage and constant current level adjustable

‧Built-in active PFC function

‧IP66 design for indoor or outdoor installations

‧

‧Cooling by free air convection

‧100% full load burn-in test

‧High reliability

‧Suitable for LED lighting and moving sign applications

‧Compliance to worldwide safety regulations for lighting

‧Suitable for dry / damp / wet locations

‧3 years warranty

Class 2 power unit

■ Features :

EMC IMMUNITY

EMC EMISSION

IP66

110

SELV

( except for 48V,54V )( for 48V,54V only)

0.6Kg;24pcs/15.4Kg/1.29CUFT

500ms / 230VAC 1200ms / 115VAC at full load

CONSTANT CURRENT REGION Note.5

Summary of content (3 pages)

PAGE 1
CEN-100 100W Single Output LED Power Supply series ■ Features : ‧Universal AC input / Full range (up to 295VAC) ‧Protections: Short circuit / Over current / Over voltage / Over temperature ‧Output voltage and constant current level adjustable ‧Built-in active PFC function ‧IP66 design for indoor or outdoor installations ‧Class 2 power unit ‧Cooling by free air convection ‧100% full load burn-in test ‧High reliability ‧Suitable for LED lighting and moving sign applications ‧Compliance to worldwide safety
PAGE 2
CEN-100 100W Single Output LED Power Supply Mechanical Specification Case No. 993A series Unit:mm 195 10.5 174 7.6 300±20 T case SJTW 18AWG×3C 86 300±20 Vo Io ADJ. ADJ. 31.25 30.6 45 62.5 AC/L(Brown) AC/N(Blue) FG (Green/Yellow) +V(Red) -V(Black) SVT 18AWG×2C 30.64 ψ4.6×4PL 40.5 ※ T case: Max. Case Temperature. Block Diagram fosc : 42KHz(115VAC) 68KHz(230VAC) EMI FILTER & RECTIFIERS I/P RECTIFIERS & FILTER POWER SWITCHING FG +V -V DETECTION CIRCUIT O.L.P.
PAGE 3
CEN-100 100W Single Output LED Power Supply series Power Factor Characteristic Constant Current Mode PF 1 .0 0 0 .9 8 0 .9 6 0 .9 4 0 .9 2 0 .9 0 0 .8 8 0 .8 6 0 .8 4 0 .8 2 0 .8 0 0 .7 8 2 7 7 V ac 2 3 0 V ac 1 1 5 V ac 50% 60% 70% 80% 90% 100% (100W) LOAD EFFICIENCY vs LOAD (48V Model) CEN-100 series possess superior working efficiency that up to 91% can be reached in field applications.