Data Sheet

ManualsBrandsMean Well Manuals19" Rack Mount PSU AccessoriesMean Well DHP-1UT-A 19" 1U rack for mean corrugated DRP-3200-series

SPECIFICATION - Power Supply System

File Name:DHP-1U RACK SYSTEM-SPEC 2019-03-22

NOTE

1. All parameters NOT specially mentioned are measured at 230VAC input, rated load and 25 of ambient temperature.℃

2. Ripple & noise are measured at 20MHz of bandwidth by using a 12" twisted pair-wire terminated with a 0.1uf & 47uf parallel capacitor. Under parallel

operation of more than one rack connecting together, ripple of the output voltage may be higher than the SPEC at light load condition. It will go back to

normal ripple level once the output load is more than 5%.

3. Tolerance : includes set up tolerance, line regulation and load regulation.

4. Output of all the DRP-3200 modules are connected in parallel in the rack.

5. Derating may be needed under low input voltages. Please check the static characteristics for more details.

6. Because of component tolerance, there is a possibility that some of units connected in parallel will reach an overcurrent limit then overloading the other

units when operating at full load condition. If overload conditions happen in parallel usage, it is suggested that derate the total output current by 10%.

7. The equivalent leakage current of the system is determined by the quantity of populated rectifiers.

8. The power supply is considered a component which will be installed into a final equipment. All the EMC tests are been executed by mounting the unit on

a mm* mm metal plate with mm of thickness. The final equipment must be re-confirmed that it still meets EMC directives.21000 1300 For guidance on how

to perform these EMC tests, please refer to EMI testing of component power supplies. (as available on http://www.meanwell.com)

9. The ambient temperature derating of 3.5 /1000m with fanless models and of 5 /1000m with fan models for operating altitude higher than 2000m(6500ft).℃℃

DHP-12K1U -24 DHP-12K1U -48

MODEL

VOLTAGE RANGE

Note.5

RECTIFIER

OUTPUT VOLTAGE

MAX. OUTPUT CURRENT

MAX. OUTPUT POWER

Note.4

FREQUENCY RANGE

AC CURRENT (Typ.) per RECTIFIER

INPUT

OUTPUT

LEAKAGE CURRENT

per RECTIFIER

90 ~ 264VAC 127 ~ 370VDC

12864W

268A

48V

DRP-3200-24 DRP-3200-48

47 ~ 63Hz

<1.5mA / 230VAC

17A/230VAC

SAFETY STANDARDS

WITHSTAND VOLTAGE

ISOLATION RESISTANCE

WORKING TEMP.

WORKING HUMIDITY

STORAGE TEMP., HUMIDITY

TEMP. COEFFICIENT

VIBRATION

DIMENSION

PACKING

OTHERS

UL60950-1, TUV EN60950-1 approved

-30 ~ +70℃ ℃

, when 3 or 4 power/charger units are paralleled in power shelf, highest working temperature shall de-rate to 40 at full load

20 ~ 90% RH non-condensing

-40 ~ +85 , 10 ~ 95% RH non-condensing℃

±℃ ℃0.03%/ (0 ~ 50 )

10 ~ 500Hz, 2G 10min./1cycle, 60min. each along X, Y, Z axes

Rack 400*482.6*44(L*W*H, with mounting bracket) ; 365*440*44(L*W*H, without mounting bracket)

ENVIRONMENT

I/P-O/P:3KVAC I/P-FG:2KVAC O/P-FG:700VDC

I/P-O/P, I/P-FG, O/P-FG:100M Ohms / 500VDC / 25 / 70% RH℃

4.85Kg

; 3pcs/17.4Kg/1.8CUFT

ALARM SIGNAL

REMOTE ON-OFF CONTROL

AUXILIARY POWER

Isolated TTL signal output for T-Alarm, AC-OK and DC-OK

By electrical signal or dry contact ON:short OFF:open

5V @ 0.3A, tolerance 10%, ripple 150mVp-p, 12V @ 0.8A, tolerance 10%, ripple 450mVp-p±±

FUNCTION

SAFETY &

EMC

(Note 8)

12768W

532A

24V

DHP-1U Rack System

3200~12800W 1U Distributed Power/Charger System

REMOTE SENSE

Compensate voltage drop on the load wiring up to 0.5V

OUTPUT VOLTAGE PROGRAMMABLE(PV)

CONSTANT CURRENT LEVEL

PROGRAMMABLE(PC)

Adjustment of constant current level is allowable to 20 ~ 100% of rated current. Please refer to the Function Manual.

Adjustment of output voltage is allowable to 50 ~ 125% of nominal output voltage. Please refer to the Function Manual.

Parameter

ESD

Radiated

EFT / Burst

Surge

Conducted

Magnetic Field

Voltage Dips and Interruptions

Conducted

Radiated

Harmonic Current

Voltage Flicker

Standard

EN55032 (CISPR32) / EN55011 (CISPR11)

EN61000-3-2

EN61000-3-3

EN61000-4-2

EN61000-4-3

EN61000-4-4

EN61000-4-5

EN61000-4-6

EN61000-4-8

EN61000-4-11

Test Level / Note

Class B

Class A

-----

EMC IMMUNITY

EMC EMISSION

EN55024 , EN61204-3, EN61000-6-2

Level 3, 8KV air ; Level 2, 4KV contact

Level 3

Level 4, 2KV/Line-Line 4KV/Line-Earth

Level 3

Level 4

>95% dip 0.5 periods, 30% dip 25 periods,

>95% interruptions 250 periods

Note.7