Datasheet

ManualsBrandsMEAN WELL ManualsLED DriversLED Driver 60W 3.4A 24V IP64

WITHSTANDVOLTAGE

ISOLATIONRESISTANCE

I/P-O/P:3.75KVACI/P-FG:2KVACO/P-FG:0.5KVAC

I/P-O/P,I/P-FG,O/P-FG:100MOhms/500VDC/25 /70%RH

¢J

CONSTANTCURRENTREGION Note.4

HLN-80H-12

B : IP64 rated. Constant current level adjustable through output cable with 1~10Vdc or 10V PWM signal or resistance.

SPECIFICATION

MODEL

DCVOLTAGE

RATEDCURRENT

RATEDPOWER

OUTPUT

VOLTAGE ADJ.RANGE

Note.6

CURRENT ADJ.RANGE

LINEREGULATION

LOADREGULATION

SETUP,RISETIME

Note.8

HOLDUP TIME (Typ.)

VOLTAGERANGE

Note.5

FREQUENCY RANGE

POWERFACTOR (Typ.)

EFFICIENCY (Typ.)

ACCURRENT (Typ.)

INPUT

INRUSHCURRENT( .)Typ

LEAKAGECURRENT

SAFETY STANDARDS

Note.7

WORKINGTEMP.

WORKINGHUMIDITY

STORAGETEMP.,HUMIDITY

TEMP.COEFFICIENT

VIBRATION

MTBF

DIMENSIONOTHERS

NOTE

PACKING

OVERCURRENT Note.4

OVERVOLTAGE

OVERTEMPERATURE

Canbeadjusted byinternalpotentiometer A typeonly

16ms atfullload230VAC/115VAC

90~305VAC127~431VDC

47~63Hz

<0.75mA /277VAC

95~108%

Protectiontype:Constantcurrentlimiting,recoversautomaticallyafterfaultconditionisremoved

Complianceto EN55015,EN61000-3-2ClassC( 60%load,12Vmodel 65%load);EN61000-3-3

¡Ù ¡Ù

CompliancetoEN61000-4-2,3,4,5,6,8,11,EN61547,EN55024,lightindustrylevel(surge4KV),criteria A

20~95%RH non-condensing

-40~+80 ,10~95%RH

¢J

¡Ó ¢J ¢J

0.03%/ (0~40 )

10~500Hz,2G12min./1cycle,periodfor72min.eachalongX, Y,Zaxes

356.4Khrsmin.MIL-HDBK-217F(25 )

¢J

181*61.5*35mm(L*W*H)

1. All parameters NOT specially mentioned are measured at 230VAC input, rated load and 25 of ambient temperature.

2. Ripple & noise are measured at 20MHz of bandwidth by using a 12" twisted pair-wire terminated with a 0.1uf & 47uf parallel capacitor.

3. Tolerance : includes set up tolerance, line regulation and load regulation.

4. Constant current operation region is within 60% ~100% rated output voltage. This is the suitable operation region for LED related applications, but please

reconfirm special electrical requirements for some specific system design.

5. Derating may be needed under low input voltages. Please check the static characteristics for more details.

6. A type only.

7. Safety and EMC design refer to EN60598-1, CNS15233, GB7000.1, FCC part18.

8. Length of set up time is measured at cold first start. Turning ON/OFF the power supply may lead to increase of the set up time.

9. The power supply is considered as a component that will be operated in combination with final equipment. Since EMC performance will be affected by the

complete installation, the final equipment manufacturers must re-qualify EMC Directive on the complete installation again.

¢J

0.5Kg;24pcs/13Kg/0.75CUFT

Protectiontype: Shutdowno/pvoltage,re-powerontorecover

80WSingleOutputSwitchingPowerSupply

¡E

Universal AC input / Full range (up to 305VAC)

Built-in active PFC function

Protections: Short circuit / Over current / Over voltage / Over temperature

Cooling by free air convection

OCP point adjustable through output cable or internal potentiometer

IP64 design for indoor or outdoor installations

Three in one dimming function (1~10Vdc or PWM signal or resistance)

Suitable for LED lighting and moving sign applications

Compliance to worldwide safety regulations for lighting

3 years warranty

Suitable for dry / damp locations or outdoor application

Class 2 power unit

¡½

Features :

HLN-80H ser ie s

RIPPLE&NOISE(max.) Note.2

VOLTAGETOLERANCE Note.3

ENVIRONMENT

SAFETY &

EMC

PROTECTION

100 10 (RTH2)

¢J¡Ó ¢J

Protectiontype: Shutdowno/pvoltage,re-powerontorecover

SELV

IP64

A : IP64 rated. Output voltage and constant current level can be adjusted through internal potentiometer.

14~17V 18~24V

23~30V

28~35V

35~43V

41~49V 54~63V

48~58V 59~68V

88%

89%

90%

90.5%

91%

91%91% 91%

¡Ó

2.5%

¡Ó

2.0%

¡Ó

1.0%

¡Ó

1.0%

¡Ó

1.0%

¡Ó

1.0%

¡Ó

1.0%

¡Ó

0.5%

¡Ó

0.5%

¡Ó

0.5%

¡Ó

0.5%

¡Ó

0.5%

¡Ó

0.5%

¡Ó

0.5%

¡Ó

2.0%

¡Ó

1.5%

¡Ó

1.0%

¡Ó

0.5%

¡Ó

0.5%

¡Ó

0.5%

¡Ó

0.5%

¡Ó

1.0%

¡Ó

0.5%

¡Ó

0.5%

¡Ó

1.0%

¡Ó

0.5%

¡Ó

0.5%

12V

HLN-80H-12 HLN-80H-30HLN-80H-15 HLN-80H-36HLN-80H-20 HLN-80H-42HLN-80H-24 HLN-80H-48 HLN-80H-54

15V 20V 24V 30V

36V

48V

5A 5A 4A 3.4A

2.7A

2.3A

1.7A

60W 75W 80W 81.6W 81W

82.8W

81.6W

150mVp-p 150mVp-p

13.5~17V

150mVp-p

17~22V

150mVp-p

22~27V

200mVp-p

27~33V

200mVp-p

33~40V

200mVp-p

43~53V10.8~13.5V

54V

1.5A

81W

200mVp-p

49~58V

42V

1.95A

81.9W

200mVp-p

38~46V

F M M

110

PF>0.96/115VAC,PF>0.96/230VAC,PF>0.94/277VACatfullload(Pleasereferto"PowerFactorCharacteristic"curve)

0.85A /115VAC0.425A /230VAC0.4A /277VAC

UL8750,CSA C22.2No.250.0-08(exceptfor48V,54V),EN61347-1,EN61347-2-13independent,IP64,J61347-1,J61347-2-13

approved;designrefertoUL60950-1, TUVEN60950-1

3~5A 3~5A 2.4~4A 2.04~3.4A 1.62~2.7A

1.38~2.3A

1.02~1.7A 0.9~1.5A

1.17~1.95A

7.2~12V 9~15V 12~20V 14.4~24V 18~30V

21.6~36V

28.8~48V 32.4~54V

25.2~42V

2000ms,80ms/115VAC 000ms,80ms/230VACatfullload;Btype2000ms,200msat95%load230VAC/115VACatfullload1

-40~+50 (Referto"DeratingCurve")

¢J

EMCIMMUNITY

EMCEMISSION

( except for 48V,54V )( for 48V,54V only)

SHORTCIRCUIT

Hiccupmode,recoversautomaticallyafterfaultconditionisremoved

FileName:HLN-80H-SPEC2013-03-04

COLDSTART 70A(t =485smeasuredat50%I )at230VACwidth peak

£g

Summary of content (5 pages)

PAGE 1
HLN-80H 80W Single Output Switching Power Supply E¡ ¡½ ¡E ¡E ¡E ¡E ¡E ¡E ¡E ¡E ¡E ¡E E¡ F HLN-80H-12 A 110 M M SELV IP64 series Features : Universal AC input / Full range (up to 305VAC) Built-in active PFC function Protections: Short circuit / Over current / Over voltage / Over temperature Cooling by free air convection OCP point adjustable through output cable or internal potentiometer IP64 design for indoor or outdoor installations Class 2 power unit Three in one dimming function (1~10Vdc or PWM
PAGE 2
HLN-80H 80W Single Output Switching Power Supply Mechanical Specification Case No.HLN-80A series Unit:mm A Type:(HLN-80H-_A) 181 ¡Ó 61.5 SVT 18AWG 2C T case 21.25 ¡Ñ +V(Red) -V(Black) ¡Ñ 90.5 SVT 18AWG 3C 6.26 35 ¡° T case: Max. Case Temperature. 2.3 AC/L(Brown) AC/N(Blue) FG (Green/Yellow) ¡Ó 300 20 2-R2.5 300 20 30.75 21.25 6.26 ¡°IP64 rated. Output voltage and constant current level can be adjusted through internal potentiometer.
PAGE 3
HLN-80H 80W Single Output Switching Power Supply Derating Curve series Static Characteristics 100 100 90 80 80 230VAC Input only 70 LOAD (%) LOAD (%) 60 40 20 -40 -25 -10 0 15 30 40 50 60 60 50 40 (HORIZONTAL) 90 ¢J AMBIENT TEMPERATURE ( ) 100 125 135 145 155 165 175 180 200 230 305 INPUT VOLTAGE (V) 60Hz Power Factor Characteristic PF Constant Current Mode 1.00 0.98 0.96 0.94 0.92 0.90 0.88 0.86 0.84 0.82 0.80 0.
PAGE 4
HLN-80H 80W Single Output Switching Power Supply series DRIVING METHODS OF LED MODULE There are two major kinds of LED drive method "direct drive" and "with LED driver". A typical LED power supply may either work in "constant voltage mode (CV) or constant current mode (CC)" to drive the LEDs. Mean Well's LED power supply with CV+ CC characteristic can be operated at both CV mode (with LED driver, at area (A) and CC mode (direct drive, at area (B).
PAGE 5
HLN-80H 80W Single Output Switching Power Supply series °¡ Using the built-in dimming function on B-type model can't turn the lighting fixture totally dark. Please refer to the connection method below to achieve 0% brightness of the lighting fixture connecting to the LED power supply unit. ¡°Direct connecting to LEDs is suggested, but is not suitable for using additional drivers.