Data Sheet

ManualsBrandsMean Well ManualsLED DriversMean Well LCM-60KN LED driver Constant current 60.3 W 500 - 1400 mA 2 - 90 Vdc dimmable

File Name:LCM-60KN-SPEC 2019-07-31

60W Multiple-Stage Constant Current Mode LED Driver

LCM-60KN series

■ Features ■ Applications

■ Model Encoding

LCM -

60KN

Output wattage

Series name

■ Description

LCM-60KN series is a 60W AC/DC constant current mode output LED driver featuring

the multiple levels selectable by dip switch and the KNX interface to avoid using the

complicated KNX-DALI gateway. LCM-60KN operates from 180 295VAC and offers～

different current levels ranging between 500mA and 1400mA. Thanks to the high efficiency

up to 91%, with the fanless design, the entire series is able to operate for -30 ~+90℃℃

case temperature under free air convection. In addition, LCM-60KN is equipped with

push dimming and synchronization so as to provide the optimal design flexibility for

LED lighting system.

LED indoor lighting

LED office lighting

LED architectural lighting

LED panel lighting

Function mode option

Type

Blank

AUX

KNX and push dimming ,with standby power consumption <0.5W

KNX and push dimming, with standby power consumption <1.2W and Auxiliary DC output

Function Note

In Stock

By request

AUX

Built-in KNX interface

Constant Current mode output with multiple

levels selectable by dip switch

KNX/EIB protocol

Flicker free design

Support emergency lighting(EL)

Integrated constant light output

Integrated KNX push button interface

Synchronization up to 10units

Functions: Manual dim, operation hours,

power consumption feedback, log/linear curve selection...etc

3 years warranty

SELV

M M

110

By request

Summary of content (9 pages)

PAGE 1
60W Multiple-Stage Constant Current Mode LED Driver EL 110 M M SELV LCM-60KN series By request ■ Features Constant Current mode output with multiple levels selectable by dip switch KNX/EIB protocol Flicker free design Support emergency lighting(EL) Integrated constant light output Integrated KNX push button interface Synchronization up to 10units Functions: Manual dim, operation hours, ■ Applications LED ni door lighting LED office lighting LED architectural lighting LED panel lightin
PAGE 2
60W Multiple-Stage Constant Current Mode LED Driver LCM-60KN series SPECIFICATION MODEL LCM-60KNCurrent level selectable via DIP switch, please refer to”DIP SWITCH TABLE” section CURRENT LEVEL 500mA RATED POWER OUTPUT 600mA 700mA(default) 2 ~ 90V 2 ~ 86V 900mA 1050mA 1400mA 2 ~ 67V 2 ~ 57V 2 ~ 42V 60.3W DC VOLTAGE RANGE 2 ~ 90V OPEN CIRCUIT VOLTAGE (max.) 95V CURRENT RIPPLE Note.5 CURRENT TOLERANCE 73V 5.0% max. @rated current ±5% AUXILIARY DC OUTPUT Nominal 12V(deviation 11.
PAGE 3
60W Multiple-Stage Constant Current Mode LED Driver LCM-60KN BLOCK DIAGRAM I/P series PFC fosc : 60KHz PWM fosc : 80KHz EMI FILTER & RECTIFIERS POWER SWITCHING PFC CIRCUIT O.L.P. PFC CONTROL O.T.P. PWM CONTROL RECTIFIERS +12Vaux (optional) RECTIFIERS & FILTER +V -V KNX+ KNX- CURRENT LIMIT MCU DETECTION CIRCUIT O.V.P. DIP SWITCH TABLE LCM-60KN is a multiple-stage constant current driver, selection of output current through DIP switch is exhibited below. DIP S.W.
PAGE 4
60W Multiple-Stage Constant Current Mode LED Driver LCM-60KN series DIMMING OPERATION ※ KNX interface Apply KNX Bus cable between KNX+ and KNX The application program(database) can be downloaded via Online Catalogs from ETS or via http://www.meanwell.com/productCatalog.
PAGE 5
60W Multiple-Stage Constant Current Mode LED Driver LCM-60KN series ※PUSH dimming or AC/DC input monitor(Primary side) ◎ PUSH dimming LCM-60KN Push Button AC/N (or Backup DC- input) AC/L (or Backup DC+ input) PUSH AC/N AC/L KNX bus need to be connected when using PUSH Dimming The detailed function of PUSH dimming, please refer to the database. The maximum length of the cable between the push button and driver is 20 meters.
PAGE 6
0W Multiple-Stage Constant Current Mode LED Driver LCM-60KN series TEMPERATURE COMPENSATION OPERATION LCM-60KN have the built-in temperature compensation function ; by connecting a temperature sensor (NTC resistor) between the +NTC / -NTC terminal of LCM-60KN and the detecting point on the lighting system or the surrounding environment, output current of LCM-60KN could be correspondingly changed, based on the sensed temperature, to ensure the long life of LED.
PAGE 7
LCM-60KN 60W Multiple-Stage Constant Current Mode LED Driver series OUTPUT LOAD vs TEMPERATURE 100 Others 80 80 60 60 40 LOAD (%) LOAD (%) 100 1050mA 20 -30 -15 0 15 30 40 50 60 70 (HORIZONTAL) AMBIENT TEMPERATURE,Ta (℃) 40 20 -30 -25 0 20 45 55 65 75 90 (HORIZONTAL) Tcase (℃) STATIC CHARACTERISTIC 100 90 80 LOAD (%) 70 60 50 40 180 190 200 210 220 230 240 250 260 270 280 295 INPUT VOLTAGE (V) 60Hz ※ De-rating is needed under low input voltage.
PAGE 8
LCM-60KN 60W Multiple-Stage Constant Current Mode LED Driver series TOTAL HARMONIC DISTORTION (THD) ※ Tcase at 80℃ 80% 60% 70% 50% 60% 30% 500mA 50% 600mA 40% THD THD 40% 700mA 20% 900mA 600mA 700mA 30% 900mA 20% 1050mA 10% 500mA 1050mA 10% 1400mA 1400mA 0% 0% 10% 20% 30% 40% 50% 60% 70% 80% 90% 100% 10% 20% 30% LOAD (230Vac Input) 40% 50% 60% 70% 80% 90% 100% LOAD (277Vac Input) POWER FACTOR (PF) CHARACTERISTIC ※ Tcase at 80℃ 1.00 0.97 0.94 500 0.
PAGE 9
LCM-60KN 60W Multiple-Stage Constant Current Mode LED Driver MECHANICAL SPECIFICATION Case No.LCM-60B series Unit:mm 123.5 6.75 6.75 6.75 110 2 TB1 3 68 1 2 3 4 5 6 TB3 1 TB4 2 1 TB5 2 ON 1 2 3 4 5 6 KNX programming button 39.3 Programming LED(RED) 65.5 7.8 2-ψ4 4 7.8 23 81.5 2 -ψ 4.2 1 6.75 Bottom View ※Terminal Pin No. Assignment( TB1 ) Pin No. 1 2 3 Assignment AC/L AC/N PUSH ※Terminal Pin No. Assignment( TB3 ) Pin No.