Datasheet

SPECIFICATION
MODEL
PLM-25E-700
RATED CURRENT
RATED POWER
OUTPUT
SETUP TIME
VOLTAGE RANGE
Note.4
FREQUENCY RANGE
POWER FACTOR
EFFICIENCY(Typ.)
AC CURRENT
INPUT
INRUSH CURRENT(Typ.)
LEAKAGE CURRENT
SAFETY STANDARDS
WITHSTAND VOLTAGE
ISOLATION RESISTANCE
WORKING TEMP.
WORKING HUMIDITY
STORAGE TEMP., HUMIDITY
TEMP. COEFFICIENT
VIBRATION
MTBF
DIMENSIONOTHERS
NOTE
PACKING
SHORT CIRCUIT
21 ~ 36V
0.7A
25.2W
5.4Vp-p
±5.0%
500ms / 230VAC at full load
180 ~ 295VAC 254~ 416VDC
47 ~ 63Hz
0.15A/230VAC 0.12A/277VAC
COLD START 15A(twidth=50 s measured at 50% Ipeak) at 230VACμ
0.25mA / 240VAC
Hiccup mode, recovers automatically after fault condition is removed.
Compliance to EN61000-4-2,3,4,5,6,8,11;EN61547, light industry level, criteria B(surge 2KV)
I/P-O/P:3.75KVAC
I/P-O/P:100M Ohms/500VDC / 25 / 70%RH℃
-30 ~ +45℃
20 ~ 90% RH non-condensing
-40 ~ +80 , 10 ~ 95% RH℃
±℃ ℃0.06%/ (0 ~ 50 )
10 ~ 500Hz, 2G 10min./1cycle, period for 60min. each along X, Y, Z axes
Protections:Short circuit
Cooling by free air convection
Fully isolated plastic case
Built-in active PFC function
Small and compact size
Class power unit, no FGⅡ
100% full load burn-in test
No load power consumption <0.5W
High reliability,low cost
Suitable for LED lighting and moving sign applications
2 years warranty
■
Features :
RIPPLE & NOISE (max.) Note.2
CURRENT ACCURACY Note.3
ENVIRONMENT
SAFETY &
EMC
PROTECTION
LED OPERATION VOLTAGE Note.5
PLM-25E-350
0.35A
25.2W
9Vp-p
NO-LOAD OUTPUT VOLTAGE(max.)
42 ~ 72V
File Name:PLM-25E-SPEC 2015-04-27
145*38*22mm (L*W*H)
808.162Khrs min. MIL-HDBK-217F (25 )℃
0.126Kg; 60 pcs / 8.6Kg / 0.48CUFT
PLM-25E-1050
14 ~ 24V
1.05A
25.2W
3.6Vp-p
85%
82%
86%
1. All parameters NOT specially mentioned are measured at 230VAC input, rated load and 25 of ambient temperature.℃
2. Ripple & noise are measured at 20MHz of bandwidth by using a 12" twisted pair-wire terminated with a 0.1uf & 47uf parallel capacitor.
3. Please see AC input voltage drop vs. output current characteristics table.""
4. Derating may be needed under low input voltage, please check the static characteristic for more details.
5. Constant current operation region is within 60% ~100% rated output voltage. This is the suitable operation region for LED related applications, but please
reconfirm special electrical requirements for some specific system design.
6. The power supply is considered as a component that will be operated in combination with final equipment. Since EMC performance will be affected by the
complete installation, the final equipment manufacturers must re-qualify EMC Directive on the complete installation again.
7. Direct connecting to LEDs is suggested, but is not suitable for using additional drivers.
PF 0.95/230VAC,PF 0.9/277VAC (at full load)(Please refer to "Power Factor Characteristic" curve)≥≥
Compliance to EN55015,EN61000-3-2 Class C( 60% load);EN61000-3-3≥
EMC IMMUNITY
EMC EMISSION
42V
80V
28V
25W Single Output LED Power Supply
PLM-25E series
PLM-25E-500
30 ~ 50V
0.5A
25W
7.5Vp-p
85%
56V
SELV
F
110
IP30
MM
ENEC EN61347-1, EN61347-2-13, EN62384, IP30 approved
18