Data Sheet

ManualsBrandsMEAN WELL ManualsPSU ComponentsAC/DC PSU module (+ enclosure) 1008 W

1000W Front End Power System

RCP-1000 series

File Name:RCP-1000-SPEC 2020-03-27

Industrial automation

Distributed power architecture system

Wireless/telecommunication solution

Redundant power system

Electric vehicle charger system

Constant current source system

■ Model Encoding / Order Information

■ Description

RCP-1000 is a 1KW single output rack mountable front end AC/DC power supply This series operates

for 90~264VAC input voltage and offers the models with the DC output mostly demanded from the industry.

Each model is cooled by the built-in DC fan with fan speed control, working for the temperature up to 60 . ℃

RCP-1000 provides vast design flexibility by equipping various built-in functions such as the output

programming, active current sharing (up to 8000W via three 19 rack shelves, RCP-1U), remote control, ”

auxiliary power, alarm signal, etc.

Universal AC input / Full range

Built-in active PFC function

High efficiency up to 89%

Forced air cooling by built-in DC fan

Output voltage programmable

Built-in OR-ing diode, support hot swap (hot plug)

Active current sharing up to 3000W for one 19 rack shelf”

Built-in I C interface (RCP-1000-C models only)

Protections: Short circuit / Overload / Over voltage /

Over temperature

Optional conformal coating

5 years warranty

■ Features ■ Applications

Output wattage

Output voltage

Interface option

24RCP - -1000

{

Blank: Standard model, without I C interface

C : Standard model, with I C interface

※ Note: 19" rack shelf, RCP-1U, available. Details available on http://www.meanwell.com/

Dimension

295

11.6

127

41 (1U)

(1U)

inch1.61

Series name

UL62368-1 TPTC004 IEC62368-1EN62368-1

Bauar

Sicherheit

egel gema

t gepr u ft

www.

ID 2000000000

tuv.com

wac g

Summary of content (6 pages)

PAGE 1
000W Front End Power System RCP-1000 series Dimension * W * H L 295 * 127 * 41 (1U) * 1.61 (1U) 11.6 * 5 mm inch Bauar t gepruft Sicherheit egel ma ge od o s be wac g www. tuv.
PAGE 2
RCP-1000 1000W Front End Power System series SPECIFICATION MODEL OUTPUT RCP-1000-12 RCP-1000-24 RCP-1000-48 DC VOLTAGE 12V 24V 48V RATED CURRENT 60A 40A 21A CURRENT RANGE 0 ~ 60A 0 ~ 40A 0 ~ 21A RATED POWER 720W 960W 1008W RIPPLE & NOISE (max.) Note.2 150mVp-p 200mVp-p 300mVp-p VOLTAGE ADJ. RANGE(SVR) 11.6 ~ 12.4V 23.2 ~ 24.8V ±1.0% 46.3 ~ 49.7V ±1.0% VOLTAGE TOLERANCE Note.3 ±1.0% LINE REGULATION ±0.5% ±0.5% ±0.5% LOAD REGULATION ±0.5% ±0.5% ±0.
PAGE 3
RCP-1000 1000W Front End Power System Block Diagram series PFC fosc : 110KHz PWM fosc : 90KHz +S ACTIVE INRUSH CURRENT LIMITING EMI FILTER I/P RECTIFIERS & PFC POWER SWITCHING RECTIFIERS & FILTER -S CURRENT SHARE CURRENT SHARE O.L.P. DETECTION CIRCUIT PWM CONTROL PFC CONTROL +V -V ORING DIODE V_TRIM O.V.P.
PAGE 4
RCP-1000 1000W Front End Power System series Function Manual 1. Voltage Drop Compensation 1.1 Remote Sense The remote sense compensates voltage drop on the load wiring up to 0.5V. +V 8 +S RCP-1000 +V LOAD 9 -S -V -V Sense lines should be twisted in pairs 1.2 Local Sense ※ The +S,-S have to be connected to the +V ,-V, respectively, as the following diagram, in order to get the correct output voltage if Remote Sense is not used. +V RCP-1000 +S -V -S 22 20 25 21 2.
PAGE 5
RCP-1000 1000W Front End Power System series 3. Output Voltage Programming (or, PV / remote voltage programming / remote adjust / margin programming / dynamic voltage trim) ※ In addition to the adjustment via the built-in potentiometer, the output voltage can be trimmed to 90~110% of the nominal voltage by applying EXTERNAL RESISTANCE. PIN8 +S PIN9 -S +V 8 +S PIN 13 V-TRIM RCP-1000 V-TRIM -S -V 13 9 R1 LOAD R2 ◎ +S & +V, -S & -V also need to be connected on CN501 3.
PAGE 6
RCP-1000 1000W Front End Power System Mechanical Specification Case No. 952A series Unit:mm 295 41 7.1 12.5 39.1 24 66 3.6 5 max. 46.3 127 46 DC OK AC OK SVR CN501 Air flow direction ※ LED Status Indicators & Corresponding Signal at Function Pins Function AC-OK AC-NG DC-OK DC-NG T-OK T-ALARM LED ON OFF ON OFF ------- * Signal Description 0 ~ 0.5V When input voltage≧82V±4V 4.5 ~ 5.5V When input voltage≦82V±4V 0 ~ 0.5V When output voltage≧80%±5% of Vo rated. 4.5 ~ 5.