Datasheet

ManualsBrandsMEAN WELL ManualsPSU ComponentsAC/DC PSU module (+ enclosure) 720 W

SPECIFICATION

MODEL

DCVOLTAGE

RATEDCURRENT

CURRENTRANGE

RATEDPOWER

OUTPUT VOLTAGE ADJ.RANGE

LINEREGULATION

LOADREGULATION

SETUP,RISETIME

HOLDUP TIME (Typ.)

VOLTAGERANGE Note.5

FREQUENCY RANGE

EFFICIENCY (Typ.)

INPUT

FUNCTION

INRUSHCURRENT (Typ.)

LEAKAGECURRENT

OVERTEMPERATURE

WORKINGTEMP.

CURRENTSHARING(CS)Note.7

OUTPUTVOLTAGETRIM Note.6

DCOKSIGNAL

REMOTEON/OFFCONTROL Note.6

AUXILIARY POWER(AUX)

WORKINGHUMIDITY

STORAGETEMP.,HUMIDITY

TEMP.COEFFICIENT

VIBRATION

MTBF

DIMENSIONOTHERS

NOTE

PACKING

OVERLOAD

OVERVOLTAGE

ACCURRENT (Typ.)

300ms,50msatfullload

16ms/230VAC16ms/115VACatfullload

90~264VAC127~370VDC

47~63Hz

12A/115VAC6A/230VAC

25A/115VAC40A/230VAC

<2.0mA /240VAC

105~125% ratedoutputpower

Protectiontype:Constantcurrentlimiting,recoversautomaticallyafterfaultconditionisremoved

13.8~16.8V 17~20.5V 27.6~32.4V 31~36.5V 56.6~66.2V

Protectiontype:Shutdowno/pvoltage,re-powerontorecover

85 5 (TSW2)detectonheatsinkofO/P diode;7

5 5 (TSW1)detectonheatsinkofpowertransistor

Protectiontype:Shutdowno/pvoltage,recoversautomaticallyaftertemperaturegoesdown

-20~+60 (Refertooutputloadderatingcurve)

Poweron:shortbetweenon/off(pin6)&-S(pin2)onCN50Poweroff:openbetweenon/off(pin6)&-S(pin2)onCN50

The TTL signalout,PSUturnon=0~1V;PSUturnoff=3.3~5.6V

Adjustmentofoutputvoltageispossiblebetween40~110%ofratedoutput

Pleaserefertofunctionmanual

5V@0.5A (+5%,-8%)

20~90%RHnon-condensing

-40~+85 ,10~95%RH

0.02%/ (0~50 )

10~500Hz,2G10min./1cycle,60min.eachalongX, Y,Zaxes

116.75Khrsmin.MIL-HDBK-217F(25 )

295*127*41mm(L*W*H)

1.95Kg;6pcs/12.7Kg/0.99CUFT

83% 85% 88% 88% 90%

0.5% 0.5% 0.5% 0.5% 0.5%

1.0% 1.0% 1.0% 1.0% 1.0%

150mVp-p

10~13.5V

150mVp-p

13.5~16.5V

150mVp-p

20~26.4V

150mVp-p

24~30V

150mVp-p

43~55V

12V

60A

0~60A

720W

15V

50A

0~50A

750W

24V

40A

0~40A

960W

27V

37A

0~37A

999W

48V

21A

0~21A

1008W

RSP-1000-12 RSP-1000-15 RSP-1000-24 RSP-1000-27 RSP-1000-48

1. All parameters NOT specially mentioned are measured at 230VAC input, rated load and 25 of ambient temperature.

2. Ripple & noise are measured at 20MHz of bandwidth by using a 12" twisted pair-wire terminated with a 0.1uf & 47uf parallel capacitor.

3. Tolerance : includes set up tolerance, line regulation and load regulation.

4. The power supply is considered a component which will be installed into a final equipment. The final equipment must be re-confirmed that it still meets

EMC directives.

5. Derating may be needed under low input voltages. Please check the derating curve for more details.

6. The power supply unit will have no output if the shorting connector is not assembled. It contains two shorting wires: one is from on/off(pin6) to -s(pin2)

and the other is from Vco(pin8) to Vca(pin10). Please refter to function manual for details.

7. In parallel connection, maybe only one unit operate if the total output load is less than 5% of rated load condition.

8. Please consult MEAN WELL for applications of more units connecting in parallel.

For guidance on how to perform these EMC tests, please refer to EMI testing of component power supplies.

(as available on http://www.meanwell.com)

POWERFACTOR (Typ.) 0.95/230VAC0.98/115VACatfullload

SAFETY STANDARDS

HARMONICCURRENT

EMSIMMUNITY

UL60950-1, TUVEN60950-1approved

CompliancetoEN55022(CISPR22)

Complianceto EN61000-3-2,-3

Complianceto EN61000-4-2,3,4,5,6,8,11;ENV50204,EN55024,EN61000-6-2,EN61204-3,heavyindustrylevel,criteria A

1000WSingleOutputPowerSupply

RSP-1000

se ri es

RIPPLE&NOISE(max.) Note.2

VOLTAGETOLERANCE Note.3

EMICONDUCTION&RADIATION

WITHSTANDVOLTAGE

ISOLATIONRESISTANCE

I/P-O/P:3KVACI/P-FG:1.5KVACO/P-FG:0.5KVAC

I/P-O/P,I/P-FG,O/P-FG:100MOhms/500VDC /25 /70%RH

ENVIRONMENT

SAFETY &

EMC

(Note4)

PROTECTION

Universal AC input / Full range

AC input active surge current limiting

Built-in 5V/0.5A auxiliary power

Built-in active PFC function, PF>0.95

Protections: Short circuit / Overload / Over voltage / Over temperature

Output voltage can be trimmed between 40 ~ 110% of the rated output voltage

Forced air cooling by built-in DC fan

Active current sharing up to 4000W(3+1)

DC OK Signal

Built-in remote ON-OFF control

Built-in remote sense function

3 years warranty

(Note.8)

High power density 10.7w/inch

1U low profile 41mm

Features :

FileName:RSP-1000-SPEC2011-02-17

Summary of content (6 pages)

PAGE 1
RSP-1000 1000W Single Output Power Supply series Features : Universal AC input / Full range AC input active surge current limiting Built-in 5V/0.5A auxiliary power Built-in active PFC function, PF>0.95 Protections: Short circuit / Overload / Over voltage / Over temperature Output voltage can be trimmed between 40 ~ 110% of the rated output voltage Forced air cooling by built-in DC fan 3 High power density 10.7w/inch 1U low profile 41mm Active current sharing up to 4000W(3+1) (Note.
PAGE 2
RSP-1000 1000W Single Output Power Supply Mechanical Specification Case No. 952B 277.7 Unit:mm 25.4 20.5 7.8 6 series 3-M4 L=6 295 21 34.5 18.5 41 59 +V -V 21 CN50 Air flow direction 90 127 SVR51 12 11 10 7 3 2 1 TB1 3-M4 L=4 7.8 20.5 25.4 3-M4 L=6 6 277.7 AC Input Terminal Pin No. Assignment Pin No. 1 2 3 Control Pi n No. Assignment (CN50) : HRS DF11-12DP-2DS or equivalent Assignment +S -S G-AUX 5V-AUX Pin No. 1 2 3 4 Assignment AC/N AC/L FG Pin No.
PAGE 3
RSP-1000 1000W Single Output Power Supply series Function Description of CN50 Pin No. Function Description Positive sensing. The +S signal should be connected to the positive terminal of the load. The +S and -S leads should be twisted in pair to +S 1 minimize noise pick-up effect. The maximum line drop compensation is 0.5V. 2 -S Negative sensing. The -S signal should be connected to the negative terminal of the load. The -S and +S leads should be twisted in pair to minimize noise pick-up effect.
PAGE 4
RSP-1000 1000W Single Output Power Supply series 2.Remote ON/OFF The PSU can be turned ON/OFF by using the "Remote ON/OFF" function Between ON/OFF(pin6) and -S(pin2) Output Status SW ON (Short) ON SW OFF (Open) OFF 1 11 2 12 -V SVR51 CN50 +V TB1 CN50 1 +S LOAD + - -S 11 CS Vci GND AUX ON/OFF Vco Vca GND AUXG DC_OK 12 2 Fig 2.1 SW 3.DC_OK signal "DC_OK" is an open collector signal. It indicates the output status of the PSU.
PAGE 5
RSP-1000 1000W Single Output Power Supply series 5.Output Voltage TRIM Output voltage of RSP-1000 can be trimmed between 40% ~ 110% of its rated value by the following methods : (1)Using external voltage source between "Vci"(pin9) and "-S"(pin2) that is shown in Fig5.1 OVP 120%(Typ.
PAGE 6
RSP-1000 1000W Single Output Power Supply series 6.Current Sharing with Remote Sensing RSP-1000 has the built-in active current sharing function and can be connected in parallel to provide higher output power : (1)Parallel operation is available by connecting the units shown as below. (+S,-S and CS are connected mutually in parallel). (2)Difference of output voltages among parallel units should be less than 2%. (3)The total output current must not exceed the value determined by the following equation.