Datasheet

ManualsBrandsMEAN WELL ManualsPSU ComponentsAC/DC PSU module (+ enclosure) 720 W

SPECIFICATION

MODEL

DC VOLTAGE

RATED CURRENT

CURRENT RANGE

RATED POWER

OUTPUT VOLTAGE ADJ. RANGE

LINE REGULATION

LOAD REGULATION

SETUP, RISE TIME

HOLD UP TIME (Typ.)

VOLTAGE RANGE

Note.5

FREQUENCY RANGE

EFFICIENCY (Typ.)INPUT

FUNCTION

INRUSH CURRENT (Typ.)

LEAKAGE CURRENT

OVER TEMPERATURE

WORKING TEMP.

CURRENT SHARING(CS)

Note.7

OUTPUT VOLTAGE TRIM

Note.6

DC OK SIGNAL

REMOTE ON/OFF CONTROL

Note.6

AUXILIARY POWER(AUX)

WORKING HUMIDITY

STORAGE TEMP., HUMIDITY

TEMP. COEFFICIENT

VIBRATION

MTBF

DIMENSIONOTHERS

NOTE

PACKING

OVERLOAD

OVER VOLTAGE

AC CURRENT (Typ.)

300ms, 50ms at full load

16ms/230VAC 16ms/115VAC at full load

90 ~ 264VAC 127 ~ 370VDC

47 ~ 63Hz

12A/115VAC 6A/230VAC

25A/115VAC 40A/230VAC

<2.0mA / 240VAC

105 ~ 125% rated output power

Protection type : Constant current limiting, recovers automatically after fault condition is removed

13.8 ~ 16.8V 17 ~ 20.5V 27.6 ~ 32.4V 31 ~ 36.5V 56.6 ~ 66.2V

Protection type : Shut down o/p voltage, re-power on to recover

Shut down o/p voltage, recovers automatically after temperature goes down

-20 ~ +60 (Refer to "Derating Curve")℃

Power on : short between on/off(pin6) & -S(pin2) on CN50 Power off : open between on/off(pin6) & -S(pin2) on CN50

The TTL signal out, PSU turn on = 0 ~ 1V ; PSU turn off = 3.3 ~ 5.6V

Adjustment of output voltage is possible between 40 ~ 110% of rated output

Please refer to function manual

5V @ 0.5A (+5%, -8%)

20 ~ 90% RH non-condensing

-40 ~ +85 , 10 ~ 95% RH℃

± ℃ ℃0.02%/ (0 ~ 50 )

10 ~ 500Hz, 2G 10min./1cycle, 60min. each along X, Y, Z axes

116.75K hrs min. MIL-HDBK-217F (25 )℃

295*127*41mm (L*W*H)

1.95Kg; 6pcs/12.7Kg/1.15CUFT

83% 85% 88% 88% 90%

±0.5% ±0.5% ±0.5% ±0.5% ±0.5%

±1.0% ±1.0% ±1.0% ±1.0% ±1.0%

150mVp-p

10 ~ 13.5V

150mVp-p

13.5 ~ 16.5V

150mVp-p

20 ~ 26.4V

150mVp-p

24 ~ 30V

150mVp-p

43 ~ 55V

12V

60A

0 ~ 60A

720W

15V

50A

0 ~ 50A

750W

24V

40A

0 ~ 40A

960W

27V

37A

0 ~ 37A

999W

48V

21A

0 ~ 21A

1008W

RSP-1000-12 RSP-1000-15 RSP-1000-24 RSP-1000-27 RSP-1000-48

1. All parameters NOT specially mentioned are measured at 230VAC input, rated load and 25 of ambient temperature.℃

2. Ripple & noise are measured at 20MHz of bandwidth by using a 12" twisted pair-wire terminated with a 0.1uf & 47uf parallel capacitor.

3. Tolerance : includes set up tolerance, line regulation and load regulation.

4. The power supply is considered a component which will be installed into a final equipment. The final equipment must be re-confirmed that it still meets

EMC directives. For guidance on how to perform these EMC tests, please refer to “EMI testing of component power supplies.”

(as available on http://www.meanwell.com)

5. Derating may be needed under low input voltages. Please check the derating curve for more details.

6. The power supply unit will have no output if the shorting connector is not assembled. It contains two shorting wires: one is from on/off(pin6) to -s(pin2)

and the other is from Vco(pin8) to Vca(pin10). Please refter to function manual for details.

7. In parallel connection, maybe only one unit operate if the total output load is less than 5% of rated load condition.

8. Please consult MEAN WELL for applications of more units connecting in parallel.

POWER FACTOR (Typ.) 0.95/230VAC 0.98/115VAC at full load

SAFETY STANDARDS UL60950-1, TUV EN60950-1 approved

Compliance to EN55022 (CISPR22), EN61000-3-2,-3

Compliance to EN61000-4-2,3,4,5,6,8,11, EN55024, EN61000-6-2, EN61204-3, heavy industry level, criteria A

1000W Single Output Power Supply

RSP -10 00

s eri es

RIPPLE & NOISE (max.)

Note.2

VOLTAGE TOLERANCE

Note.3

WITHSTAND VOLTAGE

ISOLATION RESISTANCE

I/P-O/P:3KVAC I/P-FG:2KVAC O/P-FG:0.5KVAC

I/P-O/P, I/P-FG, O/P-FG:100M Ohms / 500VDC / 25 / 70% RH℃

ENVIRONMENT

SAFETY &

EMC

(Note 4)

PROTECTION

‧

Universal AC input / Full range

‧

AC input active surge current limiting

‧

Built-in 5V/0.5A auxiliary power

‧

Built-in active PFC function, PF>0.95

‧

Protections: Short circuit / Overload / Over voltage / Over temperature

‧

Output voltage can be trimmed between 40 ~ 110% of the rated output voltage

‧

Forced air cooling by built-in DC fan

‧

High power density 10.7w/inch

‧

1U low profile 41mm

‧

Active current sharing up to 4000W(3+1)

(Note.8)

‧

DC OK Signal

‧

Built-in remote ON-OFF control

‧

Built-in remote sense function

‧

5 years warranty

■

Features :

File Name:RSP- 1000-SPEC 2013-11-01

EMC IMMUNITY

EMC EMISSION

Summary of content (6 pages)

PAGE 1
RSP-1000 1000W Single Output Power Supply series ■ Features : ‧Universal AC input / Full range ‧AC input active surge current limiting ‧Built-in 5V/0.5A auxiliary power ‧Built-in active PFC function, PF>0.95 ‧Protections: Short circuit / Overload / Over voltage / Over temperature ‧Output voltage can be trimmed between 40 ~ 110% of the rated output voltage ‧Forced air cooling by built-in DC fan ‧High power density 10.7w/inch ‧1U low profile 41mm ‧Active current sharing up to 4000W(3+1) (Note.
PAGE 2
RSP-1000 1000W Single Output Power Supply Mechanical Specification Case No. 952B 277.7 series Unit:mm 6 3-M4 L=6 295 41 21 34.5 +V -V Air flow direction SVR51 21 CN50 12 11 3 2 1 TB1 3-M4 L=4 3-M4 L=6 6 277.7 AC Input Terminal Pin No. Assignment Pin No. 1 2 3 Control Pin No. Assignment (CN50) : HRS DF11-12DP-2DS or equivalent Pin No. 1 2 3 4 Assignment AC/N AC/L FG Assignment +S -S G-AUX 5V-AUX Pin No. 5 6 7 8 Assignment DC-OK ON/OFF CS Vco Pin No.
PAGE 3
RSP-1000 1000W Single Output Power Supply series Function Description of CN50 Pin No. Function Description Positive sensing. The +S signal should be connected to the positive terminal of the load. The +S and -S leads should be twisted in pair to 1 +S minimize noise pick-up effect. The maximum line drop compensation is 0.5V. 2 3 -S Negative sensing. The -S signal should be connected to the negative terminal of the load. The -S and +S leads should be twisted in pair to minimize noise pick-up effect.
PAGE 4
RSP-1000 1000W Single Output Power Supply series 2.Remote ON/OFF The PSU can be turned ON/OFF by using the "Remote ON/OFF" function Between ON/OFF(pin6) and -S(pin2) Output Status SW ON (Short) ON SW OFF (Open) OFF 1 11 2 12 - V SV R51 CN 50 +V T B1 CN50 1 +S LO AD + - -S AUXG DC_OK 11 CS Vci GND AUX ON/OFF Vco Vca GND 2 F ig 2. 1 12 SW 3.DC_OK signal "DC_OK" is an open collector signal. It indicates the output status of the PSU.
PAGE 5
RSP-1000 1000W Single Output Power Supply series 5.Output Voltage TRIM Output voltage of RSP-1000 can be trimmed between 40% ~ 110% of its rated value by the following methods and +S & +V, -S & -V also need to be connected on CN50: (1)Using external voltage source between "Vci"(pin9) and "-S"(pin2) that is shown in Fig5.1 OVP 120%(Typ.
PAGE 6
RSP-1000 1000W Single Output Power Supply series 6.Current Sharing with Remote Sensing RSP-1000 has the built-in active current sharing function and can be connected in parallel to provide higher output power : (1)Parallel operation is available by connecting the units shown as below. (+S,-S and CS are connected mutually in parallel). (2)Difference of output voltages among parallel units should be less than 0.2V. (3)The total output current must not exceed the value determined by the following equation.