Datasheet

ManualsBrandsMEAN WELL ManualsPSU ComponentsAC/DC PSU module (+ enclosure) 1500 W

SPECIFICATION

RSP-1500-5

MODEL

DC VOLTAGE

RATED CURRENT

CURRENT RANGE

RATED POWER

OUTPUT VOLTAGE ADJ. RANGE

LINE REGULATION

LOAD REGULATION

SETUP, RISE TIME

HOLD UP TIME (Typ.)

VOLTAGE RANGE

FREQUENCY RANGE

EFFICIENCY (Typ.)

INPUT

INRUSH CURRENT (Typ.)

LEAKAGE CURRENT

OVER TEMPERATURE

WORKING TEMP.

CURRENT SHARING

OUTPUT VOLTAGE TRIM

ALARM SIGNAL OUTPUT

REMOTE ON/OFF CONTROL

AUXILIARY POWER(AUX)

WORKING HUMIDITY

STORAGE TEMP., HUMIDITY

TEMP. COEFFICIENT

VIBRATION

MTBF

DIMENSIONOTHERS

NOTE

PACKING

OVERLOAD

Note.5

OVER VOLTAGE

AC CURRENT (Typ.)

240A

0 ~ 240A

1200W

150mVp-p

4.5 ~ 5.5V

±2.0%

±0.5%

±2.0%

1500ms, 100ms at full load

10ms at full load 14ms at full load 16ms at full load

90 ~ 264VAC 127 ~ 370VDC

47 ~ 63Hz

80%

17A/115VAC 8A/230VAC

30A/115VAC 60A/230VAC

<2.0mA / 240VAC

105 ~135% rated output power

5.75 ~ 6.75V

Protection type : Constant current limiting unit will shut down o/p voltage after 5sec. Re-power on to recover

13.8 ~ 16.8V 17 ~ 20.5V 27.6 ~ 32.4V 31 ~ 36.5V 57.6 ~ 67.2V

Protection type : Shut down o/p voltage, re-power on to recover

Shut down o/p voltage, recovers automatically after temperature goes down

-20 ~ +70 (Refer to "Derating Curve")℃

Please see the Function Manual

12V@0.1A(Only for Remote ON/OFF control)

20 ~ 90% RH non-condensing

-40 ~ +85 , 10 ~ 95% RH℃

± ℃ ℃0.05%/ (0 ~ 50 )

10 ~ 500Hz, 2G 10min./1cycle, 60min. each along X, Y, Z axes

62.6K hrs min. MIL-HDBK-217F (25 )℃

278*127*83.5mm (L*W*H)

3.0Kg; 4pcs/13Kg/1.19CUFT

87% 87% 90% 90% 91%

±0.5% ±0.5% ±0.5% ±0.5% ±0.5%

±1.0% ±1.0% ±1.0% ±1.0% ±1.0%

150mVp-p

10 ~ 13.5V

150mVp-p

13.5 ~ 16.5V

150mVp-p

20 ~ 26.4V

150mVp-p

24 ~ 30V

200mVp-p

43 ~ 56V

12V

125A

0 ~ 125A

1500W

15V

100A

0 ~ 100A

1500W

24V

63A

0 ~ 63A

1512W

27V

56A

0 ~ 56A

1512W

48V

32A

0 ~ 32A

1536W

RSP-1500-12 RSP-1500-15 RSP-1500-24 RSP-1500-27 RSP-1500-48

1. All parameters NOT specially mentioned are measured at 230VAC input, rated load and 25 of ambient temperature.℃

2. Ripple & noise are measured at 20MHz of bandwidth by using a 12" twisted pair-wire terminated with a 0.1uf & 47uf parallel capacitor.

3. Tolerance : includes set up tolerance, line regulation and load regulation.

4. The power supply is considered a component which will be installed into a final equipment. The final equipment must be re-confirmed that it still meets

EMC directives. For guidance on how to perform these EMC tests, please refer to “EMI testing of component power supplies.”

(as available on http://www.meanwell.com)

5. Derating may be needed under low input voltages. Please check the derating curve for more details.

File Name:RSP- 1500-SPEC 2013-11-01

POWER FACTOR (Typ.) 0.95/230VAC 0.98/115VAC at full load

SAFETY STANDARDS

UL60950-1, TUV EN60950-1 approved

Compliance to EN55022 (CISPR22), EN61000-3-2,-3

Compliance to EN61000-4-2,3,4,5,6,8,11, EN55024, light industry level, criteria A

1500W Single Output Power Supply

RSP -15 00

s eri es

RIPPLE & NOISE (max.)

Note.2

VOLTAGE TOLERANCE

Note.3

WITHSTAND VOLTAGE

ISOLATION RESISTANCE

I/P-O/P:3KVAC I/P-FG:2KVAC O/P-FG:0.5KVAC

I/P-O/P, I/P-FG, O/P-FG:100M Ohms / 500VDC / 25 / 70% RH℃

ENVIRONMENT

SAFETY &

FUNCTION

EMC

(Note 4)

PROTECTION

‧

Universal AC input/Full range

‧

ZVS new technology

‧

AC input active surge current limiting

‧

High efficiency up to 91%

‧

Built-in active PFC function,PF>0.95

‧

Protections: Short circuit / Overload / Over voltage / Over temperature

‧

Forced air cooling by built-in DC ball bearing fan

‧

Output voltage can be trimmed between 70~100% of the rated output voltage

‧

High power density 8.3W/inch

‧

Current sharing up to 6000W(3+1)

‧

Alarm signal output

‧

Built-in 12V/0.1A auxiliary output for remote control

‧

Built-in remote ON-OFF control

‧

Built-in remote sense function

‧

5 years warranty

■

Features :

EMC IMMUNITY

EMC EMISSION

Summary of content (4 pages)

PAGE 1
RSP-1500 1500W Single Output Power Supply series ■ Features : ‧Universal AC input/Full range ‧ZVS new technology ‧AC input active surge current limiting ‧High efficiency up to 91% ‧Built-in active PFC function,PF>0.95 ‧Protections: Short circuit / Overload / Over voltage / Over temperature ‧Forced air cooling by built-in DC ball bearing fan ‧Output voltage can be trimmed between 70~100% of the rated output voltage ‧High power density 8.
PAGE 2
RSP-1500 1500W Single Output Power Supply Mechanical Specification Case No.943A 240 series Unit:mm 11.2 16 max. 38 8-M4 L=5(Both Sides) 278 11.2 240 OUTPUT +V 4-M4 L=5 -V CN1 CN2 CN3 8 6 42 8 6 42 6 4 2 7 5 31 7 5 31 5 3 1 Air flow direction I/P LED SVR 1 2 3 AC Input Terminal Pin No. Assignment Pin No. 1 2 3 Control Pin No. Assignment(CN1,CN2) : HRS DF11-8DP-2DS or equivalent Assignment FG AC/N AC/L Pin No. 1 2 3,5,7 Assignment RCG RC2 -S Pin No.
PAGE 3
RSP-1500 1500W Single Output Power Supply Derating Curve series Static Characteristics 100 Others +12V,+15V 80 100 90 60 50 +5V 80 40 70 20 -20 60 0 10 20 30 40 45 50 60 70 (HORIZONTAL) 90 AMBIENT TEMPERATURE (℃) 100 120 140 150 160 180 200 220 240 264 INPUT VOLTAGE (V) 60Hz Function Manual 1.Remote ON/OFF (1)Remote ON/OFF control becomes available by applying voltage in CN1 & CN2 & CN3 (2)Table 1.1 shows the specification of Remote ON/OFF function (3)Fig.1.
PAGE 4
RSP-1500 1500W Single Output Power Supply 2.Alarm Signal Output (1)Alarm signal is sent out through "P OK" & "P OK GND" pins (2)An external voltage source is required for this function. The maximum applied voltage is 50V and the maximum sink current is 10mA (3)Table 2.1 explain the alarm function built-in the power supply Function Description Output of alarm(P OK) The signal is "Low" when the power supply is above Low 65% of the rated output voltage-Power OK (0.