Datasheet

ManualsBrandsMEAN WELL ManualsPSU ComponentsAC/DC PSU module (+ enclosure) 2400 W

SPECIFICATION

RSP-3000-12MODEL

DC VOLTAGE

RATED CURRENT

CURRENT RANGE

RATED POWER

OUTPUT VOLTAGE ADJ. RANGE

LINE REGULATION

LOAD REGULATION

SETUP, RISE TIME

HOLD UP TIME (Typ.)

VOLTAGE RANGE

FREQUENCY RANGE

EFFICIENCY (Typ.)INPUT

INRUSH CURRENT (Typ.)

LEAKAGE CURRENT

OVER TEMPERATURE

WORKING TEMP.

CURRENT SHARING

ALARM SIGNAL OUTPUT

REMOTE ON/OFF CONTROL

AUXILIARY POWER(AUX)

WORKING HUMIDITY

STORAGE TEMP., HUMIDITY

TEMP. COEFFICIENT

VIBRATION

MTBF

DIMENSIONOTHERS

NOTE

PACKING

OVERLOAD

OVER VOLTAGE

AC CURRENT (Typ.)

12V

200A

0 ~ 200A

2400W

150mVp-p

10.8 ~ 13.2V

±1.0%

±0.5%

1000ms, 80ms at full load

10ms at full load

180 ~ 264VAC 254 ~ 370VDC

47 ~ 63Hz

86%

20A/180VAC 16A/230VAC

60A/230VAC

<2.0mA / 240VAC

100 ~ 112% rated output power

13.8 ~ 16.8V

User adjustable continuous constant current limiting or constant current limiting with delay shutdown after 5 seconds, re-power on to recover

28.8 ~ 33.6V

4.8 ~ 28V

57.6 ~ 67.2V

9.6 ~ 56V

Protection type : Shut down o/p voltage, re-power on to recover

Shut down o/p voltage, recovers automatically after temperature goes down

-20 ~ +70 (Refer to "Derating Curve")℃

Please see the Function Manual

2.4 ~ 13.2V

Please see the Function Manual

12V@0.1A(Only for Remote ON/OFF control)

20 ~ 90% RH non-condensing

-40 ~ +85 , 10 ~ 95% RH℃

± ℃ ℃0.05%/ (0 ~ 50 )

10 ~ 500Hz, 2G 10min./1cycle, 60min. each along X, Y, Z axes

104.5K hrs min. MIL-HDBK-217F (25 )℃

278*177.8*63.5mm (L*W*H)

4Kg; 4pcs/16Kg/1.89CUFT

89.5% 90.5%

±0.5% ±0.5%

±1.0% ±1.0%

150mVp-p

22 ~ 28V

200mVp-p

43 ~ 56V

24V

125A

0 ~ 125A

3000W

48V

62.5A

0 ~ 62.5A

3000W

RSP-3000-24 RSP-3000-48

1. All parameters NOT specially mentioned are measured at 230VAC input, rated load and 25 of ambient temperature.℃

2. Ripple & noise are measured at 20MHz of bandwidth by using a 12" twisted pair-wire terminated with a 0.1uf & 47uf parallel capacitor.

3. Tolerance : includes set up tolerance, line regulation and load regulation.

4. The power supply is considered a component which will be installed into a final equipment. The final equipment must be re-confirmed that it still meets

EMC directives. For guidance on how to perform these EMC tests, please refer to “EMI testing of component power supplies.”

(as available on http://www.meanwell.com)

5. Can't use the PWM signal to control the output voltage.

6. PV(PIN3) and PS(PIN4) of CN1 or CN2 must be shorted if “Output Voltage TRIM” function is not used. Otherwise, the power supply unit will have no

output.

Fil e Name:RSP -3000-SP EC 201 4-08-05

POWER FACTOR (Typ.) 0.95/230VAC at full load

SAFETY STANDARDS

UL60950-1, TUV EN60950-1 approved

Compliance to EN61000-4-2,3,4,5,6,8,11, EN55024, light industry level, criteria A

3000W Single Output Power Supply

RSP - 30 0 0

series

RIPPLE & NOISE (max.)

Note.2

VOLTAGE TOLERANCE

Note.3

WITHSTAND VOLTAGE

ISOLATION RESISTANCE

I/P-O/P:3KVAC I/P-FG:2KVAC O/P-FG:0.5KVAC

I/P-O/P, I/P-FG, O/P-FG:100M Ohms / 500VDC / 25 / 70% RH℃

ENVIRONMENT

SAFETY &

FUNCTION

EMC

(Note 4)

PROTECTION

‧

AC input 180 ~ 264VAC

‧

AC input active surge current limiting

‧

High efficiency up to 90%

‧

Built-in active PFC function,PF>0.95

‧

Protections: Short circuit / Overload / Over voltage / Over temperature

/ Fan alarm

‧

Forced air cooling by built-in DC with fan speed control function

‧

Output voltage can be trimmed between 20~110% of the rated output voltage

‧

High power density 15.6W/inch

‧

Current sharing up to 3 units

‧

Alarm signal output (relay contact and TTL signal)

‧

Built-in 12V/0.1A auxiliary output for remote control

‧

Built-in remote ON-OFF control

‧

Built-in remote sense function

‧

5 years warranty

■

Features :

EMC IMMUNITY

EMC EMISSION

OUTPUT VOLTAGE TRIM

Note.5

Compliance to EN55022 (CISPR22) Conduction Class B, Radiation Class A ; EN61000-3-2,-3

Summary of content (6 pages)

PAGE 1
RSP-3000 3000W Single Output Power Supply se rie s ■ Features : ‧AC input 180 ~ 264VAC ‧AC input active surge current limiting ‧High efficiency up to 90% ‧Built-in active PFC function,PF>0.95 ‧Protections: Short circuit / Overload / Over voltage / Over temperature / Fan alarm ‧Forced air cooling by built-in DC with fan speed control function ‧Output voltage can be trimmed between 20~110% of the rated output voltage ‧High power density 15.
PAGE 2
RSP-3000 3000W Single Output Power Supply Mechanical Specification Case No.982B se rie s Unit:mm 278 236.3 27 40 CN 1 CN 2 CN 3 8 6 4 2 8 6 4 2 10 8 6 4 2 7 53 1 7 5 3 1 9 7 5 31 8-M4(Bot h Sides) L=5mm 236.3 27 OUTPU T 4-M4 L=5mm +V -V CN 1 CN 2 CN 3 8 6 4 2 8 6 4 2 10 8 6 4 2 7 53 1 7 5 3 1 9 7 5 3 1 Air flo w direction INPUT 16max. AC Input Terminal Pin No. Assignment Pin No. 1 2 3 Control Pin No. Assignment(CN1,CN2) : HRS DF11-8DP-2DS or equivalent Assignment AC/L AC/N FG Pin No.
PAGE 3
RSP-3000 3000W Single Output Power Supply Derating Curve se rie s Static Characteristics 100 80 100 60 90 50 40 80 70 20 -20 60 0 10 20 30 40 50 60 70 (HORIZONTAL) 180 AMBIENT TEMPERATURE (℃) 185 190 195 200 210 220 230 240 250 264 INPUT VOLTAGE (V) 60Hz Function Manual 1.Remote ON/OFF (1)Remote ON/OFF control becomes available by applying voltage in CN1 & CN2 & CN3. (2)Table 1.1 shows the specification of Remote ON/OFF function. (3)Fig.1.
PAGE 4
RSP-3000 3000W Single Output Power Supply se rie s 2.Alarm Signal Output (1)Alarm signal is sent out through "P OK" & "P OK GND" and P OK2 & P OK GND2 pins. (2)An external voltage source is required for this function. (3)Table 2.1 explain the alarm function built-in the power supply. Function Description Output of alarm(P OK, Relay Contact) Output of alarm(P OK2, TTL Signal) The signal is "Low" when the power supply is above Low (0.5V max at 500mA) Low (0.
PAGE 5
RSP-3000 3000W Single Output Power Supply se rie s 4.Current Sharing (1)Parallel operation is available by connecting the units shown as below (+S,-S and CS are connected mutually in parallel): (2)The voltage difference among each output should be minimized that less than 0.2V is required. (3)The total output current must not exceed the value determined by the following equation. (Output current at parallel operation)=(The rated current per unit)×(Number of unit)×0.
PAGE 6
RSP-3000 3000W Single Output Power Supply se rie s 6.Three Phase Connect Users can exploit three units of RSP-3000(unit 1 ,unit 2,unit 3) to work with 3 ψ power system. Please refer to following diagrams for configuration. FIG. A: 3ψ3W 220VAC SYSTEM (STANDARD MODEL FOR STOCK) R unit 1 L1 FG1 N1 unit 2 L2 FG2 N2 unit 3 L3 FG3 N3 S FG T FIG. B: 3ψ4W 220/380VAC SYSTEM unit 1 L1 FG1 N1 R unit 2 L2 FG2 N2 N unit 3 L3 FG3 N3 S FG T FIG. C: 3ψ4 W 190/110VAC SYSTEM R unit 1 L1 FG1 N1 N S T (N.C.