Datasheet

ManualsBrandsMEAN WELL ManualsPSU ComponentsAC/DC PSU module (+ enclosure) 1500 W

SPECIFICATION

MODEL

DC VOLTAGE

RATED CURRENT

CURRENT RANGE

RATED POWER

OUTPUT VOLTAGE ADJ. RANGE

LINE REGULATION

LOAD REGULATION

SETUP, RISE TIME

HOLD UP TIME (Typ.)

VOLTAGE RANGE

Note.5

FREQUENCY RANGE

EFFICIENCY (Typ.)

INPUT

INRUSH CURRENT (Typ.)

LEAKAGE CURRENT

OVER TEMPERATURE

WORKING TEMP.

ALARM SIGNAL OUTPUT

REMOTE ON/OFF CONTROL

AUXILIARY POWER(AUX)

WORKING HUMIDITY

STORAGE TEMP., HUMIDITY

TEMP. COEFFICIENT

VIBRATION

MTBF

DIMENSIONOTHERS

NOTE

PACKING

OVERLOAD

OVER VOLTAGE

AC CURRENT (Typ.)

1500ms, 100ms at full load

10ms at full load

90 ~ 264VAC 127 ~ 370VDC

47 ~ 63Hz

17A/115VAC 8A/230VAC

30A/115VAC 60A/230VAC

<2.0mA / 240VAC

105 ~135% rated output power

Protection type : Constant current limiting, recovers automatically after fault condition is removed

13.8 ~ 16.8V

Protection type : Shut down o/p voltage, re-power on to recover

105 5 (TSW2 ) detect on heatsink of power transistor℃± ℃

Protection type : Shut down o/p voltage, recovers automatically after temperature goes down

-20 ~ +70 (Refer to "Derating Curve")℃

Please see the Function Manual

12V@0.1A(Only for Remote ON/OFF control)

20~90% RH non-condensing

-40 ~ +85 , 10 ~ 95% RH℃

± ℃ ℃0.05%/ (0 ~ 50 )

10 ~ 500Hz, 2G 10min./1cycle, 60min. each along X, Y, Z axes

109K hrs min. MIL-HDBK-217F (25 )℃

278*127*83.5mm (L*W*H)

3.0Kg; 4pcs/13Kg/1.19CUFT

86.5%

±0.5%

±1.0%

14ms at full load

90%

30 ~ 34.8V

16ms at full load

90%

57.6 ~ 67.2V

150mVp-p 150mVp-p 200mVp-p

±5% typical adjustment by VR, 20% ~ 110% (typ.) adjustment by 1~6VDC external control signal

12V 24V 48V

125A 63A 32A

0 ~ 125A 0 ~ 63A 0 ~ 32A

1500W 1512W 1536W

SPV-1500-12 SPV-1500-24 SPV-1500-48

1. All parameters NOT specially mentioned are measured at 230VAC input, rated load and 25 of ambient temperature.℃

2. Ripple & noise are measured at 20MHz of bandwidth by using a 12" twisted pair-wire terminated with a 0.1uf & 47uf parallel capacitor.

3. Tolerance : includes set up tolerance, line regulation and load regulation.

4. The power supply is considered a component which will be installed into a final equipment. The final equipment must be re-confirmed that it still meets

EMC directives. For guidance on how to perform these EMC tests, please refer to “EMI testing of component power supplies.”

(as available on http://www.meanwell.com)

5. Derating may be needed under low input voltages. Please check the derating curve for more details.

File Name :SPV-1500-SPEC 201 4-01-14

POWER FACTOR (Typ.) 0.95/230VAC 0.98/115VAC at full load

SAFETY STANDARDS

UL60950-1, TUV EN60950-1 approved

Compliance to EN55022 (CISPR22), EN61000-3-2,-3

Compliance to EN61000-4-2,3,4,5,6,8,11, EN55024, light industry level, criteria A

RIPPLE & NOISE (max.)

Note.2

VOLTAGE TOLERANCE

Note.3

WITHSTAND VOLTAGE

ISOLATION RESISTANCE

I/P-O/P:3KVAC I/P-FG:2KVAC O/P-FG:0.5KVAC

I/P-O/P, I/P-FG, O/P-FG:100M Ohms / 500VDC / 25 / 70% RH℃

ENVIRONMENT

SAFETY &

FUNCTION

EMC

(Note 4)

PROTECTION

‧

Universal AC input/Full range

‧

ZVS new technology

‧

AC input active surge current limiting

‧

Built-in active PFC function,PF>0.95

‧

Protections: Short circuit / Overload / Over voltage / Over temperature

‧

Forced air cooling by built-in DC ball bearing fan

‧

High power density 8.3W/inch

‧

Output voltage can be trimmed between 20% ~ 110% rated value

‧

Current sharing up to 4500W(2+1)

‧

Alarm signal output

‧

Built-in 12V/0.1A auxiliary output for remote control

‧

Built-in remote ON-OFF control

‧

Built-in remote sense function

‧

3 years warranty

■

Features :

1500W Single Output Power Supply

SPV-1500

s e rie s

OUTPUT VOLTAGE TRIM

4.8 ~ 28V 9.6 ~ 56V

2.4 ~ 13.2V

EMC IMMUNITY

EMC EMISSION

Summary of content (4 pages)

PAGE 1
S P V- 1 5 0 0 1500W Single Output Power Supply series ■ Features : ‧Universal AC input/Full range ‧ZVS new technology ‧AC input active surge current limiting ‧Built-in active PFC function,PF>0.95 ‧Protections: Short circuit / Overload / Over voltage / Over temperature ‧Forced air cooling by built-in DC ball bearing fan ‧High power density 8.3W/inch ‧Output voltage can be trimmed between 20% ~ 110% rated value ‧Current sharing up to 4500W(2+1) ‧Alarm signal output ‧Built-in 12V/0.
PAGE 2
S P V- 1 5 0 0 1500W Single Output Power Supply Mechanical Specification Case No.943A series Unit:mm 11.2 240 16 max. 38 8-M4 L=5(Both Sides) 278 11.2 240 OUTPUT +V 4-M4 L=5 -V CN1 CN2 CN3 8 6 42 8 6 42 6 4 2 7 5 31 7 5 31 5 3 1 Air flow direction I/P LED SVR 1 2 3 AC Input Terminal Pin No. Assignment Pin No. 1 2 3 Control Pin No. Assignment(CN1,CN2) : HRS DF11-8DP-2DS or equivalent Assignment FG AC/N AC/L Pin No. 1 2 3 4 Assignment RCG RC2 PV PS Pin No.
PAGE 3
S P V- 1 5 0 0 1500W Single Output Power Supply Derating Curve series Static Characteristics 100 Others 80 100 90 60 12V 50 80 40 70 20 -20 60 0 10 20 30 40 45 50 60 70 (HORIZONTAL) 90 AMBIENT TEMPERATURE (℃) 100 120 140 150 160 180 200 220 240 264 INPUT VOLTAGE (V) 60Hz Function Manual 1.Remote ON/OFF (1)Remote ON/OFF control becomes available by applying voltage in CN1 & CN2 & CN3 (2)Table 1.1 shows the specification of Remote ON/OFF function (3)Fig.1.
PAGE 4
S P V- 1 5 0 0 1500W Single Output Power Supply 2.Alarm Signal Output (1)Alarm signal is sent out through "P OK" & "P OK GND" pins (2)An external voltage source is required for this function. The maximum applied voltage is 50V and the maximum sink current is 10mA (3)Table 2.1 explains the alarm function built-in the power supply Function Description Output of alarm(P OK) The signal is "Low" when the power supply is above Low 15% of the rated output voltage-Power OK (0.