CINEMA HQ 2.
EN Index Index ................................................................................................2 Introduction ..................................................................................3 Front panel.....................................................................................3 Rear panel ......................................................................................3 Remote control ............................................................................
Introduction EN Front panel Open menu On/Off Rear panel Enter button Display Channel down/up Volume down/up SD memory card slot USB Port Coaxial Digital Audio TV aerial RF Loop HDMI TV Scart for an external TV aerial through for an external device output for connection to the TV AC Mains 3
EN Remote control 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 16. 17. 18. 19. 20. 21. 22. 23. 24. 25. 26. 27. 28. 29. 30.
Hardware configuration EN Connecting tuner to a TV Connect tuner to your TV with SCART, HDMI.
EN Software Configuration Startup Menu Wait until scanning is finished. Device now will automatically show first channel from the list. Now tuner is ready to work. If you first time turn on tuner there will be shown “Init Install” menu. Then with navigation keys setup major options: OSD LANGUAGE, COUNTRY, TIME ZONE, LCN (select LCN ON if your antenna requires power supply), then select START SEARCH and press OK to enable channel autoscanning procedure. Installation 1. Press MENU button on the remote. 2.
Manual Channel Scanning EN 1. Choose „Manual Search” menu and press OK 2. Enter default password “0000” and press OK. Auto Channel Scanning (AutoSearch) 1. Select „Auto Search” option and press OK. 2. Using navigation keys to choose “Yes” option and press OK to confirm. 3. Select “Channel No.” to choose desired channel number, next select “Frequency” – use key pad buttons to enter desired value. Next select “Bandwidth” and then select “Start Search” and press OK to start manual search.
EN Channel filter Choose „Channel Filter” to scan for all channels or only for FTA channels. 3. Choose channel from channel list on the menu. When in Full-screen mode press OK button, channel list will pop up. Use LEFT/RIGHT navigation keys to switch channel list and then use UP/DOWN navigation keys to select channel and then press OK again to confirm. Using Electronic Program Guide (EPG) 1. Press EPG button on remote. 2. Use UP/DOWN keys to explore list of available channels.
5. Press INFO button to extend program description. Press again to close info window. Note! EPG information is available only for channels that are broadcasted with EPG feature. Content and available range of information may be different for particular channels. Note! Record option activated from EPG level is available for current programs, for others you can set “reminder” – when selected program begins a message window will pop-up. 6. Press EXIT button to close EPG window. Channel Manager 1.
EN 4. You can lock selected channel pressing RED button. Enter password (default password is “0000”) and. 5. You can delete selected channel, press GREEN button. When exiting menu confirmation message will appear – select YES and press OK. 6. You can tag selected channel to be skipped when changing channels, press YELLOW button. 7. You can rename selected channel, press BLUE button. 8. Press EXIT to leave menu. Favorite List 3.
guage menu. Use UP/DOWN button to select language and then press OK to confirm. Time On OSD OSD Timeout 1st Preferred Subtitle Select duration of displaying OSD messages (2-6 seconds). Select first preffered subtitle (function dependent on broadcasted program). Switch “On” option if you want to activate constant display of actual time in the right corner. To disable this function select “Off ”.
EN 2nd Preferred Subtitle 1st Preferred Audio Select second preffered subtitle (function dependent on broadcasted program). Select first preffered audio track (function dependent on broadcasted program). Hard Hearing 2nd Preferred Audio To enable this function for hard hearing watchers select „On”. To disable select „Off ”. Select second preffered audio track (function dependent on broadcasted program).
Multimedia Music Slide Show Multimedia settings are available only when USB mass storage device is connected (pendrive or USB HDD). You can choose between following options: play all music files in selected directory repeatidly, reapeat once, or do not repeat – repeat OFF. Photo Slide Show Movie Slide Show You can choose between following options: show all images in selected directory repeatidly (Repeat-Dir) or do not repeat (Repeat-OFF).
EN BGmusic Effect You can turn ON or OFF music play durning images slideshow. You can set transformation effect between slides in slideshow mode. SlideTime You can choose duration between slides in slideshow mode (3-15sec). PVR Config In preference menu select PVR Config and press OK. Now you can modify settings regarding timeshift function and recording programs. Note! To acces these setting you must connect USB mass storage first.
PVR File Format TS: recording with subtitles, teletext and EPG (video format supported only by MT4160) PS: recording in MPEG2 file format (function available for programs broadcasted in MPEG2) Preferred Storage Select preferred storage device recording files and timeshift temporary files. Timeshift File Size Select max volume size when recording. Recorded programs will be split into volumes. You can activate timeshift function to pause on-line program and watch from the beginning of activating it.
EN Timeshift Length You can select length of timeshift (30 min -2 hours) or leave option „auto” – timeshift will record program until free space on prefered storage device ends. Setting Timeshift to Record You can select option „On” – when you press REC button program will be recorded from timeshift activation moment. Option „Off ” – temporary timeshift files will not be saved and when you press REC button - recording will start from moment when REC button was pressed.
To add timer event select empty field on the list and press OK, window will appear as shown below: tion key to enter value and press OK to confirm. ¯ Mode: select between “Weekly”, “Daily” or “Once”. ¯ Type: select type of action on timer event start. Select between “Standby” – tuner will turn off, ¯ „On” – tuner will turn on, „Recorder” – tuner will turn on and start to record desired channel, „Channel” – tuner will switch to desired channel.
EN Child Lock 1. Select “Child Lock” in setting menu, enter default password “0000” when prompted. Factory Reset 2. Select “Parental rating” and enter age of child. Programs broadcasted with child lock will be blocked. 3. Select “Change Pin Code” if you want to change default password “0000”. In field “Old Password” enter default or previous password (if you have change it once at least) and enter new password in the fields “New Password” and “Confirm Password”.
Note! Unsuccessful firmware upgrade can damage your tuner. Version Select “Version” in setting menu to show information about firmware and software version. Auto Standby Tuner can automatically turn off when no input is done by user. Select between 1-3 hour or disable this function – set option to “Off ”. AV menu EN Here you can adjust all parameters regarding video and audio output. Adjust Contrast, Brightness, Saturation, HUE.
EN Using USB storage GAME In this menu you can select game, press OK to enter game. 20 1. Plug USB mass storage device (pendrive or USB HDD) to USB port of MT4160. When device is successfully installed message will pop-up. 2. Press DEVICE button to open active device list. Here you can set partition for recording (press RED button on selected item), format partition in FAT32 (press GREEN button), format partition in NTFS (press YELLOW button) or show information (press BLUE button).
Recording EN Note! Before recording programs or using timeshift function it is necessary to set partition for that purpose. Note! It is recommended to use partition with speed level marked as green. Removing USB storage To safely remove USB mass storage/ flashcard it is recommended to turn off the tuner. If you unplug device when recording program or timeshift mode in progress you can damage file system – then you will have to format device before using it again.
EN 1. Press REC button on remote to start recording. 2. Red dot in the upper left corner will flash few times, program is recorded on preferred USB storage. 3. To stop recording press STOP button. 4. Choose “Yes” and press OK to confirm. When recording is in progress you can switch to watch another channel. You can also press INFO button to see previously recorded programs, you can play them while record is still in progress.
Playing Movies Go to Media Explorer and select MOVIE tab. Use navigation button to select desired movie file and press OK. Movie will be played in full screen mode. ¯ To play music, preview images or play movies and recorded programs select appropriate tab first. ¯ Use LEFT/RIGHT button to navigate between MOVIE, MUSIC, PHOTO, Native32GAMES, RECORD MANAGER, DISK MANAGER, EBOOK. ¯ Next press DOWN button to navigate on folder list.
EN Note! For Divx/XviD files subtitle file must have identical prefix name to be recognized. Note! Rewind/Fast Forward/GOTO function may not work for particular movie files due to difference in codec versions. Playing Music Go to Media Explorer and select MUSIC tab. Use navigation button to select desired music file and press OK. During playback press GOTO button to activate/deactivate shuffle mode, you can also press DIGEST button once to switch between repeat one/repeat directory/ repeat off mode.
UP/DOWN button or vertically – press LEFT/RIGHT button. You can press DIGEST button to switch between repeat directory /repeat off mode. Audio mode Press AUDIO button to select desired audio mode. Note! To play background music go to MUSIC tab and play music file, then go to PHOTO tab and start photo slideshow. Record Manager Go to Media Explorer and select RECORD MANAGER tab. Use navigation button to select recorded program press OK to watch it in full screen.
EN 26
Troubleshooting EN Trouble Cause Solution STANDBY indicator did not light Power cord is not plugged in Burnout fuse Check the power cord Contact with service Out of signal Antenna is not connected to receiver Incorrect direction of antenna or antenna damaged Check aerial cord Change aerial direction No sound or video Video source option in TV is wrong Choose SCART/AV video source option on TV Unclear subtitles Poor signal level Change aerial direction Reset channel list Remote control doesn
EN Technical Specification Tuner RF Input (IEC-TYPE, IEC 169-2, female) RF Output RF (IEC-TYPE, IEC 169-2, male) Frequency range: 174~230MHz (VHF) 470~862MHz (UHF) Signal Level: -15~ -70dbm Decoder: Video Decoder Audio Decoder Transfer Speed Aspect Ratio Audio Formats Resolution Movie file Photo file Music file Subtitle format MPEG-1/MPEG-2 MP@ML/MPEG-4 AVC/H.264 HP@L4.1 MPEG-1 Layer 1.2/PCM/HE-AAC v.1.