User Guide
Table Of Contents
- 1 General Information & Integration Instructions
- 1.2 Antenna information
- 1.3 Host Integration instructions
- 1.4 Host product testing guidance
- Federal Communication Commission Interference Statement
- Radiation Exposure Statement:
- This module is intended for OEM integrators only. Per FCC KDB 996369 D03 OEM Manual v01 guidance, the following conditions must be strictly followed when using this certified module:
- KDB 996369 D03 OEM Manual v01 rule sections:
- 2.7 Antennas
- The following antennas have been certified for use with this module; antennas of the same type with equal or lower gain may also be used with this module .
- This device is intended only for OEM integrators under the following conditions: (For module device use)
- Cet appareil est conçu uniquement pour les intégrateurs OEM dans les conditions suivantes: (Pour utilisation de dispositif module)
- IMPORTANT NOTE:
- IMPORTANTENOTE
- End Product Labeling
- Plaque signalétique du produit final
- Manual Information To the End User
- Manuel d'information à l'utilisateur final
- 取得審驗證明之低功率射頻器材，非經核准，公司、商號或使
- 用者均不得擅自變更頻率、加大功率或變更原設計之特性及功能。
- 低功率射頻器材之使用不得影響飛航安全及干擾合法通信；經發現有干擾現象時， 應立即停用，並改善至無干擾時方得繼續使用。前述合法通信，
- 指依電信管理法規定作業之無線電通信。
- 低功率射頻器材須忍受合法通信或工業、科學及醫療用電波輻射性電機設備之干擾。
- 本模組於取得認證後將依規定於模組本體標示審驗合格標籤。
- 應避免影響附近雷達系統之操作。
- 高增益指向性天線只得應用於固定式點對點系統。
MT7922A22M
© 2021 MediaTek Inc.
This document contains information that is proprietary to MediaTek Inc.
Unauthorized reproduction or disclosure of this information in whole or in part is strictly prohibited.
Page 9 of 14
2.10
Additional testing, Part 15 Subpart B disclaimer
This transmitter module is tested as a subsystem and its certification does not cover the FCC
Part 15 Subpart B (unintentional radiator) rule requirement applicable to the final host. The final
host will still need to be reassessed for compliance to this portion of rule requirements if
applicable.
As long as all conditions above are met, further transmitter test will not be required. However,
the OEM integrator is still responsible for testing their end-product for any additional compliance
requirements required with this module installed.
IMPORTANT NOTE: In the event that these conditions can not be met (for example certain
laptop configurations or co-location with another transmitter), then the FCC authorization is no
longer considered valid and the FCC ID can not be used on the final product. In these
circumstances, the OEM integrator will be responsible for re-evaluating the end product
(including the transmitter) and obtaining a separate FCC authorization.
Manual Information To the End User
The OEM integrator has to be aware not to provide information to the end user regarding how to
install or remove this RF module in the user’s manual of the end product which integrates this
module.
The end user manual shall include all required regulatory information/warning as show in this
manual.
OEM/Host manufacturer responsibilities
OEM/Host manufacturers are ultimately responsible for the compliance of the Host and Module.
The final product must be reassessed against all the essential requirements of the FCC rule
such as FCC Part 15 Subpart B before it can be placed on the US market. This includes
reassessing the transmitter module for compliance with the Radio and EMF essential
requirements of the FCC rules. This module must not be incorporated into any other device or
system without retesting for compliance as multi-radio and combined equipment.
Modules: extended to host manufacturers by integration instructions.