Model : IPCAM IP Wireless / Wired Camera NIGHT VISION & REMOTE PAN / TILT ROTATE User Manual
IPCAM User Manual Contents 1 WELCOME ............................................................................................................................... - 1 1.1 Features ................................................................................................................................ - 1 1.2 Packing List.......................................................................................................................... - 2 1.3 Product views...................................
IPCAM User Manual 4.3 Specification....................................................................................................................... - 33 5 OBTAINING TECHNICAL SUPPORT ......................................................................................
IPCAM User Manual 1 WELCOME IPCAM is an integrated wireless IP Camera solution. It combines a high quality digital video Camera with network connectivity and a powerful web server to bring clear to your desktop from anywhere on your local network or over the Internet. The basic function of IPCAM is transmitting remote video on the IP network. The high quality video image can be transmitted with 30fps speed on the LAN/WAN by using MJPEG hardware compression technology.
IPCAM User Manual recording and transportation. Alarm sensor input/output The detection sensor sends an alarm and records it by itself when there is a fire or accident. A message as an email is send to you by this sensor. (The input/output discreteness can be chosen) DDNS support Using the IPCAM in the condition which including ADSL and IP change often is more convenient, because IPCAM provides dynamic DNS function.
IPCAM User Manual Figure 1.1 1 2 3 4 Sensitive Hole Infrared LED Network Indicator LED If there is network activity, the LED will blink. LENS CMOS sensor.You can turn around the lens manually to adjust the focus range. 5 Built-in Mic Warning: Do not turn the Pan/Tilt by force for it may cause damage to internal components of the Pan/Tilt ! 1.3.2 Interface IPCAM01 IPCAM02 Figure 1.
IPCAM User Manual 1.5 Hardware Instruction Follow the steps below to set up your camera hardware. Make sure to follow each step carefully to ensure that the camera operates properly. 1) Plug the network cable into the camera and then into your Cable/DSL router. 2) Plug the power adapter into the camera and then into the power outlet. CAUTION: Make sure to only use the power adapter supplied with IPCAM. Using a non-approved power adapter may damage the camera.
IPCAM User Manual Figure 1.6 The computer restarts upon installation completion and an icon appears on the desktop automatically. NOTE:Before installing and using the product, please read the following precautions carefully and make sure they are fully understood. Use only the power adapter attached with the product. Use of unauthorized power adapter may cause damage to your IP Camera. IP Camera terminal shall be installed in an indoor environment.
IPCAM User Manual 2 SOFTWARE OPERATION 2.1 IP Camera Tool When the Device has been mounted properly, you can double click the icon “IP Camera Tool” and a dialog box as Figure 2.1 will pop up. Figure 2.1 Note: The software searches IP Servers automatically over LAN. There are 3 cases: 1 No IP Camera found within LAN. After about 1 minute search, the Result Field will show “not found IP Server” and the program shut automatically; 2 IP Cameras having been installed within LAN.
IPCAM User Manual Figure 2.2 z Basic Properties There are some device informations in the Basic Properties, such as Device ID, System Firmware Version, Web UI Version. Figure 2.3 z Network Configuration In this page, you can configure the Netwrok parameter. Figure 2.4 DHCP checkbox:if checked, the device will obtain IP from DHCP server (To be make sure the Router which the device connect with has DHCP function).
IPCAM User Manual Figure 2.5 z Refresh Camera List Refresh camera list manually. z Flush Arp Buffer When cable network and wireless network of the device both are fixed IP address. There is a a problem you may encounter is can search the camera IP but can’t open the camera web page.you may try to use flush arp buffer.
IPCAM User Manual 2.2 Camera Login You can access the camera through IP Camera Tool or IE directly. 1) Double click the IP address of the IP Camera listed(Figure 2.1).IE will be opened automatically and display the camera login page. 2) Access the camera by IE browser directly, type in the camera’s IP address.for example: 3) The Camera Login page pop-up. Figure 2.6 enter your account and password on the login page as shown in Figure 2.6. By default， administrator’s username is:admin and no password..
IPCAM User Manual 2.3 For Visitor Figure 2.7 For example: if is bright ,the first route is on Detection(Motion Detection). If you want to detect 4 views , need to click this ico .The first you should add more deivce.see details in 2.5.1 Multi-Device Settings. OSD: Display date and time on the video. You can disable the OSD function or choice other color.
IPCAM User Manual 2.4 For operator When login as operator or administrator,you can enter the For Operator. Figure 2.8 Direction control: click the different arrow will get different direction view. Vertical patrol Horizontal patrol Stop patrol IO output Switch on /off.(see 2.5.5 for more information) Flip: To see the flip image. Mirror: To see the mirror image.
IPCAM User Manual 2.5 For Administrator When you login as administrator, “For Administrator” is enabled. Device Info:You can find the information about Device ID,Firmware Version and Embeded Web UI Version. Alias Settings: You can Input the new name as you like. Data&Time Settings: Data&Time Settings page. Users Settings: Eight accounts are acceptable for this system. Here the eight users can configure their user names and password as Administrator, Operator or Visitor. Figure 2.
IPCAM User Manual Upgrade Device Firmware:Upgrade Device Firmware and device embeded web UI sofeware in this page. Restore Factory Settings: Restore factory settings of the device. Reboot Device:Reboot the device. Back: Back to Monitoring Mode. 2.5.1 Multi-Device Settings z Add cameras in LAN In the Multi-Device Settings page,you can see all devices searched in LAN.The 1st Device is this device deault.You can add more cameras list in LAN for monitoring.
IPCAM User Manual Figure 2.11 Figure 2.
IPCAM User Manual 2.5.2 Network Settings z Basic Network Settings If the router that the IP camera connect has DHCP function, you can choice “Obain IP from DHCP Server” else fill in the network parameters manually. Http Port:In most cases, you can leave this value as 80, however, if your Internet Service Provider blocks this port, you may switch to another port number such as 8005. Figure 2.
IPCAM User Manual and password obtained from ISP. Figure 2.15 2.5.3 DDNS Service Settings DDNS Service: The system supports protocols from some DDNS providers: Dyndns.org. User and Password: the user name and password used when applying for the domain name. (details: 4.1.6) DDNS Host: the Domain Name DDNS or Proxy Server:If you access the DDNS host through a proxy,you should input the Proxy IP. DDNS or Proxy Port: Proxy Port Figure 2.16 2.5.
IPCAM User Manual takes effect. Configure the E-mail box to receive and send mails. The E-mail box is used for receiving the images sent after alarm and the system IP address after successful dial-up. Sender: This device use the sender mailbox to send mails. Receiver: To receive the mail from the Sender.You can set up to 4 receiver mailbox.
IPCAM User Manual FTP Mode: support standard(POST) mode and passive(PASV) mode. Upload Image Now: it will upload image now when checkbox is not checked.When checked,you can input upload interval(Seconds) . FTP test: set the FTP parameter and click "Submit" first. Then click “FTP test” if succeed, it will display the prompt“FTP test succeed”.There are FTP test result: 1 Can not connect to the server. Please check FTP Server is correct or not. 2 Network Error. Please try later. 3 Server Error.
IPCAM User Manual I/O PINS: c Output(+5V) d Output eAlarm input fInput (GND) Alarm Input Armed Input Pins: The input pins can be used for 1-way external sensor input. For example, you may connect a Person Infrared Sensor (PIR) to it for motion detection. When external sensor triggered, IPCAM can be programmed to send an email with picture or control the internal relay output. If you link a external alarm with Pin3 and Pin4,when enable alarm input armed,external alarm is enabled.
IPCAM User Manual 3 HOW TO USE 3.1 Step by step to use Follow the instructions below to get started after the Camera has been mounted properly. When the IP camera powered on,it will rotate itself and stop to the center. 1) Use Network cable connect IP Camera to LAN. 2) Enter IP Camera Tool to set the basic configuration.(details: 2.1) 3) When IP address of the Camera listed in the Result Field of the IP Camera Tool, it means the basic configuiration is completed.
IPCAM User Manual 4) Wait at least 30 seconds to unplug the ethernet cable,then unplug the power supply. 5) Plug the power supply making sure that the ethernet is not connected 6) After around 30 seconds, if the LED blinks ,it indicates it is working in wifi mode 7) Camera login.(details:2.2) 3.3 Connected to the Internet through ADSL directly Figure 3.2 1) Use Network cable connect IP Camera to PC 2) Enter IP Camera Tool to set the basic configuration.(details: 2.
IPCAM User Manual Figure 3.3 1) Use Network cable connect IP Camera to the LAN. 2) Enter IP Camera Tool to set the basic configuration.(details: 2.1 ) 3) login the Camera homepage as Administration. 4) Enter DDNS Settings Page and ennable DDNS service .Click and the device will reboot. (details: 2.5.3) 5) You can access the Camera from Internet by domain name. 3.5 Static IP user Static IP user is not need to use DDNS for remote access.
IPCAM User Manual Figure 3.4 Access the IP Camera from the Internet User can access the IP Camera from the Internet,Enter WAN IP address + port number in the IE to access IP Camera.For example, Http:// 116.25.51.115:85 Note: Make sure the Port mapping is success.You can do port mapping by two ways: z Enter setting page of the router which ipcamera connect with to enable UPNP function.Enter ipcamera “Upnp Settings” to enable UPNP and make sure the state is “Upnp success”.
IPCAM User Manual 4) Enter”UPnP Settings”page,the UPnP Status should be UPnP Succeed.If the status is not Succeed,you may enter “Basic Network Settings” page to change Http Port (details: 2.5.2). Then click and reboot Device. 5) Re-login the Camera homepage to check and make sure the DDNS Status and UPnP Status is Succeed. 6) You only need to enter the domain name(domain name+Port number http://ipcam.kicks-ass.net:81/) in the IE address bar ,the browser will visit the IP Camera.
IPCAM User Manual 4 APPENDIX 4.1 Frequently Asked Questions Note: Any quesetions you would meet,please check Network connections firstly. Check the working status revealed by the indicators on the network server, hub, exchange and network card. If abnormal, check the network connections. 4.1.1 I have forgotten the administrator username and/or password. To reset the administrator username and password, Press and hold down the RESET BUTTON for 5 seconds.
IPCAM User Manual “IE” browserÆ“Tool”Æ“Internet Proper”Æ“Security”Æ“Custom Level”Æ”ActiveX control and Plug-ins” three options of front should be set to be “Enable”, The ActiveX programs read by the computer will be stored.as follows: Enable:Download unsigned ActiveX controls Enable:Initialize and script ActiveX controls not marked as safe Enable:Run ActiveX controls and plu-ins Figure 4.1 4.1.5 Problems with network bandwidth The image frame rate is subjected to the following factors: 1.
IPCAM User Manual Figure 4.2 Step2: enter your information Figure 4.3 Step3: After a minute, you will receive a E-mail from DynDNS Support and it will give you a confirmation address (e.g. https://www.dyndns.com/account/confirm/vXMVT78-KvehydmKMWH5kg) Step4: When the Account Confirmed, login and start using your account. Choose Add Host Services(Figure 4.4) and enter Add New Hostname (Figure 4.5)page.
IPCAM User Manual Figure 4.4 Figure 4.5 Step5: On the Add New Hostname page. 1) input your Hostname. 2) choose Host with IP address 3) click Use auto detected IP address xxx.xx.xx.xxx. Then click Create Host. Figure 4.6 Step6: Now you obtained a Dynamic Domain Name(Figure 4.6),and can use it in the DDNS Service Settings(details: 2.5.
IPCAM User Manual 4.1.7 Why pop-up the prompt”Fail to connect to the device…”? This prompt only appeared in the case of using multiple cameras. Enter the Multi-Device Settings page(login as administrator) to check the Device setting is correct or not. When one of the multiple cameras disconnected, the color changed to yellow and pop-up the prompt “Fail to connect to the device…”. Figure 4.2 4.1.
IPCAM User Manual but its office provides a plug-in named IE-Tabe for us and which can enable firefox to support ActiveX controls, you can access the website as follows with the firefox explorer: https://addons.mozilla.org/en-US/firefox/addon/1419 On the download page, select the right version for your browser, download it, then start the installation. Now, we take the firefox browser whose version is 2.0.0.18 as the example to describe the whole procedure.
IPCAM User Manual 5 In the end click “Restart Frefox” button to restart the browser. 6 Login your device and locate the monitoring page, click your mouse’s right button, click the new menu item named View page in IE-Tab to login device again. 4.
IPCAM User Manual IP address: dynamic obtain Subnet mask:255.255.255.
IPCAM User Manual 4.3 Specification ITEMS Image Sensor Lens Audio Video Communication IPCAM01/02 Image Sensor 1/4" Color CMOS Sensor Disaplay Resolution 640 x 480 Pixels(300k Pixels) Lens(01) f: 6mm, F:1.8 (IR Lens) Lens(02) f: 3.6mm, F:1.8 (IR Lens) Mini. Illumination 0.
IPCAM User Manual Supported OS Microsoft Windows 2000/XP/Vista Browser IE 5.0,IE 6.0, IE7.0, IE8.0 firefox2.0 firefox3.0 or other standard browsers Certification Warranty CE,FCC Limited 1-year warranty 5 OBTAINING TECHNICAL SUPPORT While we hope your experience with the IPCAM network camera is enjoyable and easy to use, you may experience some issues or have some questions that this User’s Guide has not answered.
