Operation Manual

ManualsBrandsMedion ManualsMonitorMD30004

Contents:

SAFETY INSTRUCTION ...................................................................................................... 1

Purpose of use .............................................................................................................. 1

Operating Safety ........................................................................................................... 1

Repair..........................................................................................................................1

Setting up location......................................................................................................... 2

Intended Environment.................................................................................................... 2

Connecting ................................................................................................................... 2

Power Supply.............................................................................................................. 2

Standards/Electro-Magnetic Compatibility ......................................................................... 3

Recycling and disposal.................................................................................................... 3

Maintenance and care .................................................................................................... 3

FCC Compliance Statement........................................................................................... 4

Declaration of Conformity ............................................................................................. 4

INTRODUCTION ............................................................................................................... 5

Notes on these instructions ............................................................................................. 5

Our Target Group ........................................................................................................ 5

Quality....................................................................................................................... 5

Service ...................................................................................................................... 5

INCLUDED EQUIPMENT ..................................................................................................... 5

START-UP ....................................................................................................................... 6

Preparations on Your Computer ....................................................................................... 6

Supported Monitor Settings .......................................................................................... 6

Display Properties ....................................................................................................... 7

Unpacking .................................................................................................................... 8

Installing the base plate ................................................................................................. 8

Connecting the Monitor................................................................................................... 8

n Connecting VGA Signal Cable..................................................................................... 9

o Connecting Audio Cable ............................................................................................ 9

p Connecting the Power Supply..................................................................................... 9

Positioning of the Monitor ............................................................................................... 9

CONTROLS.................................................................................................................... 11

SETTING THE LCD MONITOR ........................................................................................... 11

How to operate the OSD menu ...................................................................................... 11

Leaving the OSD menu................................................................................................. 12

OSD Menu .................................................................................................................. 12

Brightness / Contrast................................................................................................. 12

Image control ........................................................................................................... 12

Color ....................................................................................................................... 13

OSD Control ............................................................................................................. 13

Other ...................................................................................................................... 13

Reset....................................................................................................................... 13

Saving Energy............................................................................................................. 13

Summary of content (21 pages)

PAGE 1
Contents: SAFETY INSTRUCTION ...................................................................................................... 1 Purpose of use .............................................................................................................. 1 Operating Safety ........................................................................................................... 1 Repair ....................................................................................................................
PAGE 2
SERVICE....................................................................................................................... 14 Troubleshooting........................................................................................................... 14 Finding the problem ..................................................................................................... 14 Check Connections and Cables ....................................................................................
PAGE 3
Safety Instruction Please read through this section carefully and follow the instructions given. In this way you will guarantee reliable operation and a long life for your LCD monitor. Always keep these instructions handy and close by your LCD monitor. Keep the instructions and the packaging so that if you sell or give away your LCD monitor you can give them to the new owner. Purpose of use • This device is only suitable for using in dry, internal rooms. • This device is intended for personal use only.
PAGE 4
Setting up location • In the first hours of operation, new devices may emit a typical, unavoidable but completely harmless smell, which will decline increasingly in the course of time. We recommend you to ventilate the room regularly, in order to counteract the formation of the smell. During the development of this product, we have made sure that the applicable limits are clearly fallen below. • Keep your LCD display away from moisture and avoid dust, heat and direct sunlight.
PAGE 5
Standards/Electro-Magnetic Compatibility Your monitor fulfils the requirements for electro-magnetic compatibility and electrical safety specified in the following standards: EN 55022 Information technology equipment - Radio disturbance characteristics - Limits and methods of measurement. EN 55024 Information technology equipment - Immunity characteristics - Limits and methods of measurement. EN 60950 Safety of information technology equipment.
PAGE 6
FCC Compliance Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
PAGE 7
Introduction Notes on these instructions We have arranged these instructions so that you can quickly find the subject related information in the table of contents. The purpose of these instructions is helping you operate your LCD display safely, quickly and easily. Our Target Group Thank you for purchasing our LCD display. We thank you for your confidence in our products and are pleased to greet you as a new customer. These instructions are intended for initial users as well as advanced users.
PAGE 8
Start-Up Note: Before start-up always read the Chapter “Safety Instruction” on page 1. Preparations on Your Computer If you have operated your computer previously with a CRT monitor, it will be necessary for you to make a few preparations. This is required when your previous monitor was operated with settings which are not supported by your new LCD monitor. Supported Monitor Settings This monitor supports the following modes: Horizontal Frequency Resolution Vertical Frequency 720 x 400 31.
PAGE 9
Display Properties This Windows program offers you the possibility of adapting the display to your monitor. This includes items such as the background image, the screen saver, the Active Desktop (Web) as well as other settings for your monitor and video card. The program can be started as follows: • Right mouse click on Windows desk top and left mouse click on "Properties". or • Start the "Display" program in "System control“. The resolution can be set under “Screen resolution”. (n).
PAGE 10
Unpacking 1. Please keep the packaging material well and use it exclusively to transport the monitor. 2. Screws to attach the base plate will be in the packaging. Keep them away from children; there is a danger of swallowing them. Installing the base plate 1. Place a soft, clean pad under the monitor, so that it will not be possible for the surfaces to be scratched or damaged. 2. Place the monitor with the back on a flat and stable surface. 3. Position the base plate on the foot of the monitor. 4.
PAGE 11
n Connecting VGA Signal Cable 3. Plug the signal cable into the matching VGA sockets on the computer. If your PC features a DVI port, you can connect your monitor by means of the DVI plug. You can connect a YPbPr signal source by means of the YPbPr - VGA data cable. o Connecting Audio Cable 4. Plug the audio cable into the matching sockets on the computer. p Connecting the Power Supply 5.
PAGE 12
(similar picture) • Hand’s support rest: 2” – 4” • Top line of screen should keep eye’s level or be a little beneath • Eye’s distance to screen: 20” – 28” • Legroom (vertical): at least 26” • Legroom (horizontal): at least 24” 10 ENGLISH
PAGE 13
Controls Symbol Meaning < > Description Down • When OSD is active this key sets a parameter value and decreases it. Decrease volume • Executing it directly lowers the volume. Up • When OSD is active this key sets a parameter value and increases it. Increase volume • Executing it directly raises the volume. On/Off switch • With this switch you can switch the LCD monitor ON and OFF. Operation indicator • Indicates the operating state. Blue = Normal mode, Orange = Stand-by mode.
PAGE 14
Leaving the OSD menu To exit the OSD menu you have different possibilities: • Choose Exit • The OSD vanishes from the screen automatically, when you do not press any key on the monitor during the preset time interval (factory setting is 10 seconds). OSD Menu The following will introduce the main functions and settings of the OSD. (similar picture) Note: Due to technical modifications the menus described here might differ from those on your screen.
PAGE 15
Color • 9300K / 6500K Set one of the preset values using the < and > keys. • Custom color Select this option using the MENU key, if you want to set the values for red, green and blue individually. The new values will be saved automatically on exiting this menu item. OSD Control • H. OSD Phase Adjust the horizontale position of the OSD. • V. OSD Phase Adjust the vertical position of the OSD. • OSD timeout You can set the idle time interval, after which the OSD will vanish.
PAGE 16
Service Troubleshooting If your LCD monitor should have problems please check if it is properly installed and plugged according to the information given in the “Start-Up” section beginning on page 6). If the problems cannot be solved, read the following chapter for possible solution. Finding the problem Many times, problems have simple causes. We would like to give you some tips to solve some common problems.
PAGE 17
The display is too light or too dark: • Check that the video output level of the computer matches the technical data of the monitor. • Select Auto Setup, to optimize the settings for brightness and contrast. The display should show a text page (e.g. Explorer, Word, etc.), to optimize it. The image is jittering: • Check whether the operating voltage matches the technical specifications of the monitor. • Select Auto Setup to optimize the settings for pixel and phase synchronization.
PAGE 18
Specifications Parameter Data Visible display size 20,1“ Resolution 1680 x 1050 (WSXGA) Refresh rate max. 75 Hz Brightness 300 cd/m² (typ) Contrast 800:1 (typ.) Viewing angle (horizontal/vertikal) 88° / 88° Refresh rate 8 ms (typ.
PAGE 19
WARRANTY The receipt serves as proof of first purchase and should be kept in a safe place. Your legal rights are not limited by these warranty conditions. It is required should you need to make use of the guarantee. We guarantee that this equipment is in perfect working order. Upon production of the receipt, the remaining period of guarantee shall pass on from the original parts to the respective replacement parts.
PAGE 20
Types of Pixel Failures: • Type 1: A constantly lit pixel (a bright, white spot), even though it is not addressed. A white pixel is caused when all three sub-pixel are lit. • Type 2: A pixel that does not light up (dark, black spot), although it is addressed. • Type 3: Abnormal or defective red, green or blue sub-pixels. (E.g. constantly lit with half the brightness, one color is not shining, blinking or flickering, but not belonging to Type 1 or 2 Pixel Failures).
PAGE 21
Liability limitations The contents of this manual are subject to unannounced changes caused by technical progress. Manufacturer and sales shall not be responsible for any damages which have been caused as a result of omissions or errors in the information provided in this manual: 1. Claims made against you by third parties based on loss or damage. 2. Loss or damage to your blanks, recordings or data. 3.