USB Graphics tablet © 2004 Medion®. All rights reserved. Trademarks: Microsoft, MS-DOS and Windows are either registered trademarks or trademarks of Microsoft Corporation in the United States and/or other countries. Intel and Pentium are trademarks or registered trademarks of Intel Corporation or its subsidiaries in the United States and other countries. Other trademarks are property of their respective owners. Artwork is for illustrative purposes only. Actual product appearance may vary.
CONTENTS Safety and Maintenance .........................................................3 Ergonomics.............................................................. 4 Inventory .................................................................. 4 Technical data ............................................................ 5 System requirements .................................................. 5 Usage ....................................................................... 5 Getting Started.....................
SAFETY AND MAINTENANCE Keep these instructions with your graphics tablet at all times. The proper set up, use and care can help extend the life of your graphics tablet. In the event that you transfer ownership of this device, please provide these instructions to the new owner. Ö Whenever you edit your data, make backup copies on an external data medium (e.g., floppy disks, CD). We not liable for loss of data and consequential damages.
Ö Before cleaning the devices, remove the cable connection from the computer. Clean the devices and other components with a damp cloth. Do not use any solvents, corrosive or gaseous detergents. Ö When connecting additional or other components the EMC (electromagnetic compatibility) directives must be adhered to. Do not operate the mouse when it is in the charger. The devices are not intended for use in a heavy industry environment.
TECHNICAL DATA Active surfaces 9 x 12 in. (height x width) Maximum resolution 3048 lpi / 120 lpmm Sensitivity 512 Steps Connection USB Environment temperature 41° F – 104° F Humidity 20% - 80% (non- condensing) Mouse operating battery Microcells LR03 AAA type, 1.5V Pen operating battery Microcells LR03 AAA Type, 1.5V Certification CE, FCC, VCCI CI.
GETTING STARTED INSERT THE BATTERY INTO THE PEN - + 1. Turn the rear end of the pen counterclockwise, as you would with a ballpoint pen, and remove the rear end. 2. Put one of the included batteries into the pen, (see above illustration). Make sure that the end of the battery marked with "+" appears at the pen top and that end marked with "- " points to the end of the rear contact spring 3. Replace the rear end of the pen again and turn it clockwise to tighten.
USED BATTERIES - WASTE DISPOSAL ÂImportant note: Batteries are toxic and must be properly disposed of. Replace the empty batteries only with the same or an equivalent battery type.
INSTALLATION OF THE GRAPHICS TABLET The following installation instructions are applicable to the Microsoft® Windows® operating system versions 98SE/ME/2000/XP. The installation is basically the same with all of these operating systems. Here are some tips to complete the installation successfully. • Have ready the Installation CD for the Graphics tablet. • Also have ready the Installation CD of your computer’s operating system in case you need it.
DRIVER INSTALLATION 1. Follow the guidelines in the chapter "Safety and Maintenance" (from page 2). 2. Place the PC, the Graphics tablet, the pen and the mouse on your work surface so that you can work comfortably and safely with them. 3. Switch on the computer and all the connected peripherals (monitor, printer, external modem etc.), and wait until the operating system has been fully started. 4. Locate a free USB port on your computer. 5.
Note: If the CD does not start automatically, it is likely that the CD Autorun function has been deactivated. Read the respective chapter in Windows Help on how to activate this function. What follows is an example of a manual installation without the CD Autorun function: 1. Click on and select the item (Or hit á + R to launch the corresponding dialog). 2. Now enter the letter of the CD-ROM drive followed by a colon and the program name setup: 3. Click on “OK“. 4.
UNINSTALLING APPLICATIONS In order to remove the installed software from your PC, follow the steps below: 1. Click on 2. Click on 3. Finally, double click on the following icon: Select the appropriate program from the list, start the uninstallation and follow the instructions on screen. CONFIGURING THE GRAPHICS TABLET Click on Click on Double click on the Pad 9570 icon in order to configure the Graphics tablet.
CUSTOMER SERVICE WHAT TO DO IN THE EVENT OF PROBLEMS BASIC HINTS ¾ Run the Windows® programs “Defrag” and “Scandisk” regularly to remove sources of error and increase system performance. TROUBLESHOOTING Start with a careful visual check of all cable links. If the indicator lights are not working, make sure that the power is reaching the computer and all attached peripherals. 12 ¾ Switch the computer off and check all cable connections.
TECHNICAL SUPPORT This program has been extensively and successfully tested in our test laboratory with a number of different PC setups. It is nevertheless quite normal for the drivers to be updated from time to time. This means that problems of compatibility with other, as yet untested, components (programs, devices) may arise. Driver updates and the most up-to-date information on this product can be found at the following Internet address: Internet: http://www.medion-usa.
This page is intentionally left blank.
WARRANTY MEDION warrants to our customers that this product is free from defects in materials and workmanship as follows: for a period of one (1) year from the date of original purchase, defective parts or a defective product returned to a MEDION repair facility or a MEDION Authorized Service Facility ("ASF") for such product, as applicable, and proven to be defective upon inspection, will be exchanged for new or comparable rebuilt parts, or a refurbished product, as determined by the MEDION repair facility
PURCHASE PRICE OF THE PRODUCT SOLD BY MEDION WHICH CAUSED THE ALLEGED DAMAGE. WITHOUT LIMITING THE FOREGOING, YOU ASSUME ALL RISK AND LIABILITY FOR LOSS, DAMAGE OR INJURY TO YOU AND YOUR PROPERTY AND TO OTHERS AND THEIR PROPERTY ARISING OUT OF USE OR MISUSE OF, OR INABILITY TO USE THE PRODUCT NOT CAUSED DIRECTLY BY THE NEGLIGENCE OF MEDION.