User Manual

8 9
bed using the swing-out hooks. Do not hook on a slanted or curved surface.
3. Measure patient’s calf/foot/thigh circumference at the widest point to
ensure proper fit.
4. Application of the Calf/Thigh sleeve(s).
a) Sleeves come in identical pairs and may be used on either leg.
b) Unfold the sleeve and lay the unfolded sleeve on a flat surface with
the inside of the sleeve facing up.
c) When using dual sleeves, the identical sleeves type (same model) must
be used on both legs. Sleeves combinations are calf and calf, thigh and
thigh or foot and foot.
d) Position the sleeves at the appropriate ankle or knee landmark.
e) Place the patient’s leg on the sleeve lining, position the back of the knee
over the popliteal opening in the case of thigh high sleeve.
f) Starting at the side opposite the air hose, wrap the main flap of the
sleeve snugly around the patient’s leg.
g) Fasten the sleeve securely with the hook and loop fasteners starting at the
ankle and then moving to the calf and/or thigh. Secure with tabs starting at
the bottom tab marked 1, moving upwards to tab 2 then 3, etc.. Check that
none of the hook and loop flaps hang off the end of the sleeve (entirety of
hook and loop area is secured to the sleeve). The sleeves should fit securely
but not tightly around all parts of the patient’s leg. Confirm sleeve is
properly sized by checking that the index line falls between the range
markers. Follow the instructions and select the next size up or down if the
index line falls out of range.
h) Use the “two-finger” rule to check that the correct fit is used. Insert 2 fingers
horizontally (with palm up and both fingers touching the patient’s leg) in
between the sleeve and the patient. This practice should be done at both
the top and bottom of the sleeves.
i) Using the same procedures apply the second identical model sleeve if
needed. If only one is to be used, simply leave the unused air outlet on the
pump free (no air hose attached).
5. Application of the Foot sleeve(s).
a) Foot sleeves come in identical pairs and may be used on either foot.
b) When using dual sleeves the identical sleeves type (same model) must
be used on both legs. Do not use in any other combination. Place the
sleeve on patient’s foot ensuring the hook and loop attachments are visible.
c) Ensure a snug fit by placing two fingers around the back of the sleeve to
ensure the sleeve is not too tight. Routinely inspect the patient’s feet
once compression commences.
d) Using the same procedures, apply the second identical model sleeve if
needed. If only one sleeve is to be used simply leave the unused
air outlet on the pump free (no air hose attached).
6. Air hose(s) are required to connect the sleeve(s) to the pump and are provided
separately. Attach the sleeve(s) to the air hose(s) using the connectors. Each
tube has a male end connector at one end and a female connector at the other.
The female end will fit to the male end on the sleeve. Make certain that a click
sound is heard to ensure a proper connection.
7. Attach the other end(s) of the air hose(s) (male end) to the female connector(s)
on the pump. Make certain that a click is heard with each snap lock connection. If
you need to disconnect tubing, firmly pull the male and female connector apart.
8. Press and hold the power button to turn pump on when air hose(s) and
sleeve(s) are properly connected.
9. Pump will start initialization process lasting approximately 40 seconds.
10. The pump will automatically detect single/dual identical model of sleeve(s)
during initialization process and will automatically default to the calf/thigh
pressure setting.
11. The pump can be manually switched to foot therapy by pressing “FOOT”
indicator for 5 seconds while pump is in initialization step. The LED light of
“FOOT” will be on when foot therapy is activated.
12. To turn pump off, hold POWER button for 5 seconds.
13. To disconnect device, remove plug from electrical outlet.
14. Respond to the instrument alarms appropriately and refer to troubleshooting
guide on pump.
15. To remove the sleeves, firmly pull the connectors apart.
Recommendations during operation
• Avoid placing the tubing and/or any connections or components under the
patient as this may negatively impact the effectiveness of the pump and/or
cause a skin integrity issue for the patient.
• Make sure that there are no kinks in the tubing and that the connectors are
properly locked.
• Never apply or remove the sleeves while inflated as this may cause damage
to the sleeve.
• The parts and/or accessories supplied are specifically designed for use with
Hemo-Force Lite control unit. Use of other products in conjunction with the
system is not recommended.
• Respond to the instrument audio indicator appropriately and follow the
manufacturer’s recommendations.