Installation Instructions Part 1
Table Of Contents
- Table of Contents
- CHAPTER 1 Description of the Medtronic MiniMed 2007C Implantable Insulin Pump System 11
- CHAPTER 2 Indications and Contraindications 21
- CHAPTER 3 Personal Pump Communicator (PPC) 25
- CHAPTER 4 Pump Implantation 77
- CHAPTER 5 Pump Refill Procedure 97
- CHAPTER 6 Explanting the Pump System 107
- CHAPTER 7 Warnings And Precautions 109
- CHAPTER 8 Adverse Reactions 115
- CHAPTER 9 System Alarms and Messages 117
- CHAPTER 10 Troubleshooting Pump System Under-delivery 131
- CHAPTER 11 MiniMed 2007C Implantable Insulin Pump System 133
- APPENDIX A Label Information 137
- APPENDIX B Implant Worksheet 141
- APPENDIX C Refill Form 143
- APPENDIX D Precautions and General Procedures 145
- APPENDIX E Pump Rinse Procedure 151
- APPENDIX F Side Port Catheter Flush Procedure 163
- APPENDIX G Stroke Volume Measurement 175
- APPENDIX H Pressure Measurement Using The Side Port Catheter 181
- CHAPTER 1 Description of the Medtronic MiniMed 2007C Implantable Insulin Pump System
- CHAPTER 2 Indications and Contraindications
- CHAPTER 3 Personal Pump Communicator (PPC)
- Introduction
- Part 1: PPC/Pump system initialization
- Part 2: Additional PPC programming features
- Main menu
- Program a bolus
- Set a normal bolus with the variable bolus feature turned off
- Set a normal bolus with the variable bolus feature turned on
- Set a square wave bolus
- Set a dual wave bolus
- Review bolus history
- Suspend mode
- Programming a basal rate
- Programming basal delivery pattern
- Setting basal rate profiles in each delivery pattern
- Program a temporary basal rate
- Set a temporary basal rate
- Stop a temporary basal rate
- Personal events
- History
- Main menu
- Setup Pump
- Setup II
- Audio bolus
- Activating the audio bolus feature
- Set an audio bolus from the main menu bolus screen
- Variable bolus
- Refill
- Priming
- Diagnostic rate
- Initialize to factory defaults
- Download software
- Stop Pump
- Supervisor password
- Exit supervisor
- Personal Pump communicator messages
- Clinical history codes
- Clinical history PPC/Pump codes
- Audio bolus
- CHAPTER 4 Pump Implantation
Personal Pump Communicator (PPC)
44
Set a normal bolus with the variable bolus feature turned on
1. From the Time/Date screen press SEL
until the “BOLUS” screen is displayed.
The last bolus value programmed and the
Time and Date will be flashing.
2. Press ACT and the “SET BOLUS TYPE”
screen appears. If “NORMAL” is not
flashing, use the ▲
▲▲
▲ and ▼
▼▼
▼ buttons to
select “NORMAL.” Press ACT.
3. The “SET BOLUS” screen appears, with
dashes under “IMM” flashing. Use the ▲
▲▲
▲
and ▼
▼▼
▼ buttons to enter an immediate
bolus amount.
4. Press ACT and the “CONFIRM” screen
is displayed, with the screen flashing.
Confirm the bolus amount by pressing
ACT again.
5. Place the PPC near the Pump and com-
plete the communication process.
6. When the bolus programming is com-
plete, the PPC will beep once and then
briefly display the amount of insulin cur-
rently delivered.
The Pump will beep at each of the first five strokes (if audio feedback is
ON). The PPC beeps at the end of the bolus. Three segments of the insulin
delivery icon will be displayed and spinning slowly during the bolus
delivery. By pressing SEL you can read the amount of insulin delivered.
08:13 Jan 02
BOLUS
IMM EXT
-- U -- U
SET
NORMAL
BOLUS TYPE
SET BOLUS
IMM
--- --- U
CONFIRM
IMM
2.6u
PPC
COMMUNICATING
08:23 JAN 04
0.0U
BOLUS
Dmp9196021-011_c.book Page 44 Thursday, April 4, 2002 8:15 AM