Installation Instructions Part 1
Table Of Contents
- Table of Contents
- CHAPTER 1 Description of the Medtronic MiniMed 2007C Implantable Insulin Pump System 11
- CHAPTER 2 Indications and Contraindications 21
- CHAPTER 3 Personal Pump Communicator (PPC) 25
- CHAPTER 4 Pump Implantation 77
- CHAPTER 5 Pump Refill Procedure 97
- CHAPTER 6 Explanting the Pump System 107
- CHAPTER 7 Warnings And Precautions 109
- CHAPTER 8 Adverse Reactions 115
- CHAPTER 9 System Alarms and Messages 117
- CHAPTER 10 Troubleshooting Pump System Under-delivery 131
- CHAPTER 11 MiniMed 2007C Implantable Insulin Pump System 133
- APPENDIX A Label Information 137
- APPENDIX B Implant Worksheet 141
- APPENDIX C Refill Form 143
- APPENDIX D Precautions and General Procedures 145
- APPENDIX E Pump Rinse Procedure 151
- APPENDIX F Side Port Catheter Flush Procedure 163
- APPENDIX G Stroke Volume Measurement 175
- APPENDIX H Pressure Measurement Using The Side Port Catheter 181
- CHAPTER 1 Description of the Medtronic MiniMed 2007C Implantable Insulin Pump System
- CHAPTER 2 Indications and Contraindications
- CHAPTER 3 Personal Pump Communicator (PPC)
- Introduction
- Part 1: PPC/Pump system initialization
- Part 2: Additional PPC programming features
- Main menu
- Program a bolus
- Set a normal bolus with the variable bolus feature turned off
- Set a normal bolus with the variable bolus feature turned on
- Set a square wave bolus
- Set a dual wave bolus
- Review bolus history
- Suspend mode
- Programming a basal rate
- Programming basal delivery pattern
- Setting basal rate profiles in each delivery pattern
- Program a temporary basal rate
- Set a temporary basal rate
- Stop a temporary basal rate
- Personal events
- History
- Main menu
- Setup Pump
- Setup II
- Audio bolus
- Activating the audio bolus feature
- Set an audio bolus from the main menu bolus screen
- Variable bolus
- Refill
- Priming
- Diagnostic rate
- Initialize to factory defaults
- Download software
- Stop Pump
- Supervisor password
- Exit supervisor
- Personal Pump communicator messages
- Clinical history codes
- Clinical history PPC/Pump codes
- Audio bolus
- CHAPTER 4 Pump Implantation
Part 2: Additional PPC programming features
49
Review bolus history
To review the type, amount, time and day of your last 512 insulin boluses.
1. From the Time/Date screen, press SEL.
The “BOLUS” screen is displayed, show-
ing the last bolus programmed.
Use the ▲
▲▲
▲ and ▼
▼▼
▼ buttons to display pre-
vious boluses, along with the time and
day each bolus was delivered.
Suspend mode
The Suspend Pump mode allows the user to cancel a bolus delivery, while
still delivering a basal rate of 0.2 U/hr.
1. From the Time/Date screen, press SEL
until the “SUSPEND PUMP” screen is
displayed. Press ACT. The screen will
display a flashing “SUSPEND PUMP”
message. Press ACT again.
2. Place the PPC near the Pump and com-
plete the communication process.
3. When the communication is complete, the
Pump will beep 3 times and the PPC
screen will change to “PUMP SUS-
PENDED”. All four segments of the
insulin delivery icon are shown. The PPC
will beep every half-hour as long as the
Pump remains suspended.
NOTE: To restart the pump, press SEL. The “PUMP
SUSPENDED” screen will begin flashing. Then
press ACT.
08:23 Jan 02
BOLUS
--- ---
IMM EXT
---- U --- --- U
PROG
SUSPEND PUMP
PPC
COMMUNICATING
08:13 OCT 12
PUMP SUSPENDED
Dmp9196021-011_c.book Page 49 Thursday, April 4, 2002 8:15 AM