Installation Instructions Part 1
Table Of Contents
- Table of Contents
- CHAPTER 1 Description of the Medtronic MiniMed 2007C Implantable Insulin Pump System 11
- CHAPTER 2 Indications and Contraindications 21
- CHAPTER 3 Personal Pump Communicator (PPC) 25
- CHAPTER 4 Pump Implantation 77
- CHAPTER 5 Pump Refill Procedure 97
- CHAPTER 6 Explanting the Pump System 107
- CHAPTER 7 Warnings And Precautions 109
- CHAPTER 8 Adverse Reactions 115
- CHAPTER 9 System Alarms and Messages 117
- CHAPTER 10 Troubleshooting Pump System Under-delivery 131
- CHAPTER 11 MiniMed 2007C Implantable Insulin Pump System 133
- APPENDIX A Label Information 137
- APPENDIX B Implant Worksheet 141
- APPENDIX C Refill Form 143
- APPENDIX D Precautions and General Procedures 145
- APPENDIX E Pump Rinse Procedure 151
- APPENDIX F Side Port Catheter Flush Procedure 163
- APPENDIX G Stroke Volume Measurement 175
- APPENDIX H Pressure Measurement Using The Side Port Catheter 181
- CHAPTER 1 Description of the Medtronic MiniMed 2007C Implantable Insulin Pump System
- CHAPTER 2 Indications and Contraindications
- CHAPTER 3 Personal Pump Communicator (PPC)
- Introduction
- Part 1: PPC/Pump system initialization
- Part 2: Additional PPC programming features
- Main menu
- Program a bolus
- Set a normal bolus with the variable bolus feature turned off
- Set a normal bolus with the variable bolus feature turned on
- Set a square wave bolus
- Set a dual wave bolus
- Review bolus history
- Suspend mode
- Programming a basal rate
- Programming basal delivery pattern
- Setting basal rate profiles in each delivery pattern
- Program a temporary basal rate
- Set a temporary basal rate
- Stop a temporary basal rate
- Personal events
- History
- Main menu
- Setup Pump
- Setup II
- Audio bolus
- Activating the audio bolus feature
- Set an audio bolus from the main menu bolus screen
- Variable bolus
- Refill
- Priming
- Diagnostic rate
- Initialize to factory defaults
- Download software
- Stop Pump
- Supervisor password
- Exit supervisor
- Personal Pump communicator messages
- Clinical history codes
- Clinical history PPC/Pump codes
- Audio bolus
- CHAPTER 4 Pump Implantation
Pump Implantation
84
27. With the stopcock closed, press the refill needle into the Pump fill
port.
28. Open the stopcock. Maintain downward pressure on the barrel of the
syringe to ensure the inlet valve of the Pump remains open.
Never push on the refill syringe plunger to
fill the Pump. When the refill needle is
properly seated in the fill port of the
Pump, the vacuum in the reservoir will
draw the insulin from the syringe.
29. Allow the Pump vacuum to draw the INSULIN into the reservoir.
When the INSULIN stops moving, the Pump is filled. Close the stop-
cock and remove the syringe.
30. Prepare the IN1 syringe for aspiration. Remove any air from the
syringe, prime the needle, close the stopcock and obtain a vacuum by
pulling back on the plunger until it locks. Press the lock into the
plunger groove to be sure it is firmly secured. A fluid barrier of at
least 2 mL should remain in the syringe.
31. Press the refill needle back into the Pump fill port with the stopcock
closed.
32. Open the stopcock and empty the Pump. Allow 30 seconds after the
INSULIN level appears to have stopped rising in the refill syringe to
assure the Pump is completely emptied.
33. Close the stopcock and remove the syringe.
!
WARNING
Dmp9196021-011_c.book Page 84 Thursday, April 4, 2002 8:15 AM