MDuo DUAL DRIVER NOISE-ISOLATING HEADSET MDuo DUAL DRIVER NOISE-ISOLATING HEADSET
M-Duo Dual Dynamic Driver Noise-Isolating In-Ear Headset
Specifications Driver: Dual dynamic drivers Impedance: 16 ohms + 15% @ 1K 1mW Frequency response: Sensitivity: Noise isolation: Cable length: Rated input power: Max power input: Operational temperature: Storage temperature: 10 Hz to 20 KHz 101 dB up to 27 dB 135 cm / 53 in 2mW 5mW -10 °C to 55 °C (14 °F to 120 °F) -20 °C to 60 °C (-4 °F to 140 °F) MEElectronics and its logo are registered trademarks of S2E, Inc. All rights reserved.
It the sound is louder in one ear than the other there are several possible reasons: - The song or source is not balanced: try another song and/or source - There is pressure buildup in your ear; release it by pulling back on the earphone housing, pulling the upper part of your ear to release the pressure, or both - Your ears require different sized ear tips: swap the channels and see if you still hear an imbalance on the same side (i.e.
Warning Fit and ear tips play a major role in how you hear your earphones. If the bass on your MEElectronics earphones is missing or seems weak, you have not achieved a good seal with your earphone. If the earphones sound quiet, you are more than likely not inserting them deep enough in your ears. If you are using the large triple flange tips, they can bend in your ear canal muffling the sound. Please check the 'First Use' section for instructions on achieving the best fit for you.
First Use: Selecting Tips A proper seal between the earpiece and your ear canal is required to achieve the best sound quality with the MEElectronics M-Duo. Please follow the instructions in the manual to make sure you get a proper seal. It may take several minutes to get the correct fit, but it will result in better long term sound, comfort, and noise isolation. Select and install the correct ear tips for your ears This may require trying multiple sizes/types of ear tips.
Cleaning Cleaning your MEElectronics products regularly is hygienic and will help keep the earphones looking their best.
How to Wear: Inserting Earpiece The M-Duo is designed to be worn in a traditional manner with the cable down. It can also be worn with the cable over the ear - please see page 6 for more information. Care and Storage Removing the cable from your device: Each earphone has a channel indicator with an R for right and an L for left. The inline microphone and remote is located on the cable for the left channel. Do not pull on the cable; remove by the hard plastic of the 3.5mm plug 1.
Microphone Use The microphone is directional and needs to be near your mouth to operate properly. If you are not loud or clear while talking into the microphone, adjust the location of the microphone so it is in front of your mouth. At times, poor voice clarity can be a result of poor call connection quality, in which case you should hang up and redial.
How to Wear: More Options Using the cable cinch: The cable cinch can effectively shorten the length of the cable after the Y split for use behind the back or to keep the earphones in place more securely. Tighten the cable cinch and use the shirt clip to reduce cable movement during activities. The cable cinch does not go beyond the inline mic/remote housing; however the cable cinch can still reduce cable movement.
How to Wear: More Options Using the cable cinch: The cable cinch can effectively shorten the length of the cable after the Y split for use behind the back or to keep the earphones in place more securely. Tighten the cable cinch and use the shirt clip to reduce cable movement during activities. The cable cinch does not go beyond the inline mic/remote housing; however the cable cinch can still reduce cable movement.
Microphone Use The microphone is directional and needs to be near your mouth to operate properly. If you are not loud or clear while talking into the microphone, adjust the location of the microphone so it is in front of your mouth. At times, poor voice clarity can be a result of poor call connection quality, in which case you should hang up and redial.
How to Wear: Inserting Earpiece The M-Duo is designed to be worn in a traditional manner with the cable down. It can also be worn with the cable over the ear - please see page 6 for more information. Care and Storage Removing the cable from your device: Each earphone has a channel indicator with an R for right and an L for left. The inline microphone and remote is located on the cable for the left channel. Do not pull on the cable; remove by the hard plastic of the 3.5mm plug 1.
Cleaning Cleaning your MEElectronics products regularly is hygienic and will help keep the earphones looking their best.
First Use: Selecting Tips A proper seal between the earpiece and your ear canal is required to achieve the best sound quality with the MEElectronics M-Duo. Please follow the instructions in the manual to make sure you get a proper seal. It may take several minutes to get the correct fit, but it will result in better long term sound, comfort, and noise isolation. Select and install the correct ear tips for your ears This may require trying multiple sizes/types of ear tips.
Warning Fit and ear tips play a major role in how you hear your earphones. If the bass on your MEElectronics earphones is missing or seems weak, you have not achieved a good seal with your earphone. If the earphones sound quiet, you are more than likely not inserting them deep enough in your ears. If you are using the large triple flange tips, they can bend in your ear canal muffling the sound. Please check the 'First Use' section for instructions on achieving the best fit for you.
It the sound is louder in one ear than the other there are several possible reasons: - The song or source is not balanced: try another song and/or source - There is pressure buildup in your ear; release it by pulling back on the earphone housing, pulling the upper part of your ear to release the pressure, or both - Your ears require different sized ear tips: swap the channels and see if you still hear an imbalance on the same side (i.e.
Specifications Driver: Dual dynamic drivers Impedance: 16 ohms + 15% @ 1K 1mW Frequency response: Sensitivity: Noise isolation: Cable length: Rated input power: Max power input: Operational temperature: Storage temperature: 10 Hz to 20 KHz 101 dB up to 27 dB 135 cm / 53 in 2mW 5mW -10 °C to 55 °C (14 °F to 120 °F) -20 °C to 60 °C (-4 °F to 140 °F) MEElectronics and its logo are registered trademarks of S2E, Inc. All rights reserved.