Manual

• Impo
• This product contains a light source of energy efficiency class <X >
rtant warning for drilling in walls: before drilling, make sure that there are no gas and water pipes or power lines behind or near the drilling spots. Drilling and mounting
should be performed only by qualified personnel. Be sure to pay attention at the condition and material of the walls, as the mounting material is not suitable for all wall types.
Please inquire about recommended screws and raw plugs for your wall type and wall condition. The manufacturer accepts no liability for improper wall raw plug mounting and
the herefrom resulting damages.
MEGATRON
®
T8-LED-Triproof Luminaire 1,5m – LUTO
TECHNICAL SPECIFICATION:
Instruction Manual
Series Name
MEGATRON
®
LUTO 1x22W
MEGATRON
®
LUTO 2x22W
Model Number MT77342
Color Grey
Incl. lamp 1x LM85286E
Light source energy efficiency class <X>
Wattage T8 Lamp 22W
Luminous Flux T8 Lamp 2500lm
CCT 4000K
Voltage 220-240V
Frequency 50/60Hz
IP Rating IP65
Through Wiring Option No
MT77343
Grey
2x LM85286E
2x22W
E E
2x2500lm
4000K
220-240V
50/60Hz
IP65
No
CAUTIONS:
• Read the entire manual carefully before installation and operation.
• Installation or replacement should be pe rformed only by licensed and qualified electricians.
• The luminaire is only compatible with LED T8 tubes. The usage of fluorescent T8 tubes is not allowed!
• DO NOT disassemble the inner part of the luminaire. Doing so may result in luminaire damage or malfunction.
• Switch OFF the power source before installation, replacement and cleaning!
• Wearing gloves during installation is recommended to ensure the luminaire is kept in the best condition.
• Before replacement of the luminaire or the T8 lamp, turn it off and allow it to cool down. Heat-resistant gloves are mandatory when handling the luminaire or the T8 lamp.
• The manufacturer accepts no liability for any damage resulting from the misuse of the luminaire or from when it is used with inappropriate equipment.
• Consult your dealer if you have any enquiries.
MOUNTING:
1. 2. 3.
4.
5.
1. Turn the power supply OFF.
2.
3. Remove the cover of the triproof luminaire.
4. Screw the T8 LED tube out of the socket and remove the protective packaging.
5. Mount the M16 PG gland at the cable entry point of the luminaire.
6.
to ensure the waterproof protection.
7. Screw the T8 LED tube into the socket.
8. Close the luminaire cover and mount the 14 PC clips into the receptacles of the luminaire.
9. Insert the triproof luminaire into the holder to fix the luminaire on the wall.
10. Switch the power supply ON.
6.
7.
8.
PG-gland M16
9.
OFF
10.
GB
IDV GmbH | Birkenweiherstraße 2 | D-63505 Langenselbold | Germany | www.megatron-licht.eu
Correct disposal of this product:
This marking indicates that this product should not be disposed with other household wastes throughout the EU. To prevent possible harm to the environment or
human health from uncontrolled waste disposal, recycle it responsibl y, to promote the sustainable reuse of material resources. To return your device, please use the
return and collection systems, or contact the retailer where the product was purchased. They can take this product for environmental safe recycling.
ON
• Designed for indoor and outdoor applications.
• Instant start is allowed.
• The operating temperature of the luminaire is -20°C to +40°C.
ATTENTION:
2 pcs.14 pcs.1 pcs. 4 pcs. 4 pcs.
INCLUDED PARTS:
L=Brown
=Yellow/Green
N=Blue
Drill the drill holes, insert the dowels into the drill holes and screw the bracket on the wall or ceiling.
Conduct the power cable through the PG gland and connect it to the push terminal. Close the PG gland by screwing the cap clockwise and double check the correct fit of the seal