Specifications

Power Distribution Section
Voltage Adjustments . . . . . . . . . . . . . . 2 - 8
Module Replacement . . . . . . . . . . . . . . 2 - 8
Presser Foot / Associated Parts Replacing . 3 - 24
R
Reciprocator / Needle Bar Guide Shaft . . . 3 - 31
Retainer Plate Bearing Adjustment . . . . . . 3 - 30
Rotary Hook
Replacement . . . . . . . . . . . . . . . . . . . 3 - 36
Retaining Finger Positioning . . . . . . . . 4 - 29
S
Scope Of Manual . . . . . . . . . . . . . . . . . . . . 1 - 1
Select Position
Adjustment . . . . . . . . . . . . . . . . . . . . 4 - 22
Checking . . . . . . . . . . . . . . . . . . . . . . 4 - 21
Sequence of Trim Events . . . . . . . . . . . . . . 4 - 1
Sew Test. . . . . . . . . . . . . . . . . . . . . . . . . . 4 - 32
Specifications, Various Technical . . . . . . . . 1 - 8
Standard Conventions Used In Manual. . . . 1 - 1
Static Electricity . . . . . . . . . . . . . . . . . . . . . 1 - 3
T
Table Top Removal . . . . . . . . . . . . . 2 - 8, 2 - 11
Thread Break Contact Post Replacement . 3 - 13
Thread Guide Tubes . . . . . . . . . . . . . . . . . 3 - 10
Thread Tensioner Assembly Removal . . . . . 3 - 9
Trimmer
Adjustment Procedures . . . . . . . . . . . 4 - 10
Damaged Cam or Solenoid. . . . . . . . . 4 - 11
Not Trimming Properly . . . . . . . . . . . . 4 - 13
Physical Condition Of Parts. . . . . . . . . 4 - 13
Replacement Procedures . . . . . . . . . . . 4 - 2
Trimmer Cam . . . . . . . . . . . . . . . . . . . . . . . 4 - 4
Trimmer Drive Assembly . . . . . . . . . . . . . . . 4 - 4
Trimmer Solenoid . . . . . . . . . . . . . . . . . . . . 4 - 4
Troubleshooting LEDs and Test Points . . . . 1 - 6
U
Under Thread Control (UTC)
Adjustments. . . . . . . . . 3 -38, 3 -44, 4 - 29
Replacement . . . . . . . . . . . . . . . . . . . 4 - 28
Under Thread Presser
Description. . . . . . . . . . . . . . . . . . . . . 4 - 14
Replacement . . . . . . . . . . . . . . . . . . . . 4 - 8
V
Voltage Adjustments . . . . . . . . . . . . . . . . . 2 - 8
W
Warranty Considerations. . . . . . . . . . . . . . 1 - 3
Wide Angle Cap Frame
Cap Frame. . . . . . . . . . . . . . . . . . . . . . 5 - 4
Cap Supports . . . . . . . . . . . . . . . . . . . 5 - 1
Cap Support Pads . . . . . . . . . . . . . . . . 5 - 2
Clip Posts. . . . . . . . . . . . . . . . . . . . . . . 5 - 3
Driver Bar Cable . . . . . . . . . . . . . . . . . 5 - 2
Spindles On The Clamps . . . . . . . . . . . 5 - 3
X
X Beam Assembly . . . . . . . . . . . . . . . . . . 2 - 17
X Drive Belt
Belt Tension. . . . . . . . . . . . . . . . . . . . 2 - 20
Replacement . . . . . . . . . . . . . . . . . . . 2 - 19
X Motor Replacement . . . . . . . . . . . . . . . 2 - 17
XYZ Motor Driver Amplifiers . . . . . . . . . . 2 - 15
Y
Y Drive Belt
Replacement . . . . . . . . . . . . . . . . . . . 2 - 25
Tension Adjustment . . . . . . . . . . . . . 2 - 28
Y Motor
Belt Tension. . . . . . . . . . . . . . . . . . . . 2 - 23
Replacement . . . . . . . . . . . . . . . . . . . 2 - 21
Z
Z Motor
Belt Tension. . . . . . . . . . . . . . . . . . . . . 3 - 3
Replacement . . . . . . . . . . . . . . . . . . . . 3 - 1
Z Shaft Encoder
Calibration . . . . . . . . . . . . . . . . . . . . . 3 - 6
Inspection . . . . . . . . . . . . . . . . . . . . . . 3 - 4
Installation. . . . . . . . . . . . . . . . . . . . . . 3 - 5
Introduction . . . . . . . . . . . . . . . . . . . . 3 - 3
Z Timeout Errors . . . . . . . . . . . . . . . . . . . 4 - 10
INDEX
110291-01, Revision D ii EMT 10T Technical Manual