Operation Manual

ManualsBrandsMeliconi ManualsRemote ControlGumbody Facile 3 web

Keep this booklet for future reference.

Thank you for choosing a Meliconi remote control.

The Facile 3 web remote control is ideal for replacing up to 3 remote controls for TV - SAT (satellite decoder)

- TER (Digital Terrestrial decoder). Moreover, thanks to its AUDIO UPDATE function, the device can also be

connected to a PC via the cable supplied in order to download the information required to conﬁ gure it. And not

only: the Facile 3 web remote control has a LEARN function so it can learn any original remote control signals

not yet inserted in the databank, as well as allowing secondary functions to be acquired and saved on the F1 -

F2 - F3 - F4 function keys or on any other button on the keypad.

The remote control has a non-volatile memory, meaning that it does not lose its settings even if there are no

batteries in it. Its ergonomic shape and soft rubber body make it easy to grip and protect the remote control if it

is knocked or dropped.

IMPORTANT: The remote control must not be exposed to excessive heat sources.

USE OF THE BUTTONS AND FUNCTIONS

The functions of the buttons described below are available only if they are on your original device.

Volume control +/–

TELETEXT buttons

ON/OFF switches the device OFF and

in some cases ON

Numeric keypad

Conﬁ rm selection

MUTE turns sound OFF and ON

For selecting an external

input source

For selecting the next programme

P+ or the previous programme P–

For moving around within the MENU

Buttons for selecting the device to be

controlled.

Fastext functions or for selecting sub-

menus using colours

Speciﬁ c buttons for decoder

Displays the list of programmes

Selects analogue/digital

Selects digital TV and radio

Button for activating the LEARN function.

The button lights up when commands are

being captured or transmitted

User customised buttons that additional

commands can be saved to and accessed

directly from

web

Summary of content (7 pages)

PAGE 1
EN I web Thank you for choosing a Meliconi remote control. Keep this booklet for future reference. The Facile 3 web remote control is ideal for replacing up to 3 remote controls for TV - SAT (satellite decoder) - TER (Digital Terrestrial decoder). Moreover, thanks to its AUDIO UPDATE function, the device can also be connected to a PC via the cable supplied in order to download the information required to configure it.
PAGE 2
Before using the remote control, insert the batteries and programme it. INSERTING THE BATTERIES The remote control requires 2 new 1.5V alkaline AAA/LR03 batteries. Insert them as illustrated. Try pressing a number button and check that the red light remains lit continuously until you release the button. If the light flashes, the batteries inserted are not charged and are about to go flat, therefore you must substitute them.
PAGE 3
NOTE: If you don’t receive an SMS on your cell phone or if the message says ERROR / NO CODE, it means the system has not been able to process the data you have sent. Do not try sending another SMS use the MANUAL SEARCH instead. SETTING CODES USING A MANUAL SEARCH (only to be performed if the specific code could not be found) 1. Switch on the device to be programmed and select a program 2.
PAGE 4
If they do not appear, repeat the procedure. If this still does not work it means the code indicated is not in the remote control, so it must be loaded using the INTERNET as described in the following section. UPDATING VIA AUDIO CABLE Connect the remote control using the audio cable in the kit supplied to a PC with an internet connection. Connect the cable as follows: 1. Open the remote control battery compartment. 2.
PAGE 5
Learning missing functions from an original remote control and saving them on any button on the Facile 3 web To acquire signals you must first make sure that the remote controls are the correct distance apart: 1. Position the original remote control in front of the universal remote control so that the areas which emit the infrared signals are opposite each other at a distance of approximately 5 cm. 5 cm 2.
PAGE 6
Learning all the functions from a new remote control not yet included in the Facile 3 web databank With the Facile 3 web you can create up to 5 completely empty keypads so that in LEARN mode a total of up to 64 new commands can be obtained. 1. Follow the code entry procedure using one of the following codes: 8000, 8100, 8200, 8300, 8400. 2. To acquire and save signals from one or more original remote controls follow this procedure .
PAGE 7
TROUBLESHOOTING PROBLEM The device does not respond and the indicator light does not come on when a button is pressed. SOLUTION Check that the batteries are charged and inserted correctly and if necessary replace them with 2 new 1,5 V AAA/LR03 alkaline type batteries. The device does not respond but the indicator light comes on. Make sure that the remote control is pointing at the device and that there are no obstacles in the way.