Rechargeable2-in-1-Vacuum Cleaner User Guide

14
15
PREPARING THE APPLIANCE
For safety reasons, the battery is only partially charged
when the appliance leaves the factory. Therefore, you
must always start by charging the battery fully. Charge
the appliance for 10-12 hours before rst use.
Battery charging
1. Make sure the appliance is switched off.
2. Place the appliance in the holder (21).
3. Insert the charger (16) into the mains socket and
connect the cord to the charger socket (20) on the
holder.
4. Switch on the power. The blue recharging indicator
(8) on the appliance lights up.
5. Leave the battery to fully charge – approx. 8-10
hours, if the battery is completely discharged.
o The recharging indicator remains lit while the
appliance is connected to the charger.
Tips!
We recommend always leaving the appliance in the
charger when not in use so that the appliance is always
ready to use.
NOTE:
• The battery becomes hot during charging – this is
perfectly normal.
• Make sure the appliance is switched off on both
on/off buttons (2 and 7) before charging.
USING THE APPARATUS
This apparatus can be used both as a oor vacuum
and as a hand-held vacuum. Use the oor vacuum to
vacuum oors. Use the hand-held vacuum cleaner to
vacuum difcult-to-reach spots.
Before using the appliance, check that the lter (10) is
correctly tted in the dust container (12) (see “Emptying
of dust container and cleaning of lter”).
Using the vacuum cleaner
1. Make sure the hand-held vacuum cleaner (5) has
been correctly tted to the appliance.
2. Attach the oor nozzle (6) by inserting the connector
(17) into the terminal at the point of the appliance
and pressing the appliance onto the nozzle.
o Turn on the appliance by pushing the on/off
button (2) on the foldable handle (1) forward.
3. Push the on/off button backward to the “OFF”
position to swith off the appliance.
Using the hand-held vacuum cleaner
1. Detach the hand-held vacuum cleaner from the
appliance by pressing the release button (4) whilst
simultaneously pulling the hand-held vacuum
cleaner upwards.
2. Push the on/off button (7) forward to switch on the
appliance and backward to switch it off.
3. The crevice nozzle (13) is tted to the hand-held
vacuum cleaner and can be extended from the
nozzle tip (12) when cleaning difcult to reach spots
(see illustration).
4. Attach the hand-held vacuum
into the hollow on the appliance
until you hear a click, once you
have nished using it.
NOTE:
• If the appliance loses suction power during use, the
battery may need to be recharged.
• Lack of suction power may also be caused by
the lter being blocked and needing cleaning (see
“Cleaning of dust container and emptying of lter”).
• If the appliance still does not have full suction power
after cleaning or replacing the lter, the nozzle tip or
the nozzle may be blocked.
• NOTE: Check cause of fault and correct. Do not
use the appliance if any air holes are blocked.
Permanent motor damage can result.
• We recommend that you empty the dust container
after each vacuuming (see “Emptying of dust
container and cleaning of
lter” below).
Tips!
To save room during storage,
the handle of the appliance
may be folded. Press down
the release button for the foldable handle (3) and tilt the
handle toward the appliance (see illustration).
DUST CONTAINER AND FILTER
This appliance is not equipped with a dust bag. The
dust/dirt is sucked up into the transparent dust holder
instead. The air sucked in is cleaned by means of a
two-component washable permanent lter in the dust
container.
Emptying of dust container and cleaning of lter
IMPORTANT! If the appliance loses suction power
during use, the lter pad may be dirty, and needs
cleaning or replacing. Never use the appliance, when
the lter is dirty or when it has not been tted.
1. Detach the hand-held vacuum cleaner from the
appliance by pressing the release button whilst
simultaneously pulling the hand-held vacuum
cleaner upwards.
2. Grab the dust container with one hand and twist it
to release the dust container from the motor section
(15) (see illustration).
3. Pull the two parts of the lter out of the dust
container and empty the container. If necessary,
rinse the dust container with clean water and wipe
the container with a dry cloth.
4. The lter consists of two sections, both of which
must be cleaned. Brush the parts with a small
brush and/or wash them in tepid water. Add a
little detergent if necessary. Check the lter pad
is COMPLETELY dry before
replacing in the appliance.
NEVER insert a wet lter into
the appliance.