AMPLIF IERS 16-MXA1.500 16-MXA 4.480 16-MXA 5.
WELCOME TO MEMPHIS! Thank you for choosing Memphis Xtreme Audio. Your choice of Memphis Xtreme Audio indicates a desire for high quality music in any environment. Memphis brings you over four decades of audio expertise. So whether you are a daily driving music lover, or a serious car audio competitor, Memphis has the product for you! To take full advantage of the Memphis Xtreme Audio gear you have just purchased, please read and follow the instructions in this manual.
INSTALLA TION Professional installation by an authorized Memphis Car Audio/Xtreme Audio dealer is highly recommended. Otherwise the performance of your new gear may not be satisfactory. In the event that you decide to do your own installation, please read and follow this manual very carefully. Failure to read and follow the guidelines in this manual may compromise the integrity of this product and your vehicle, and could possibly void the product warranty.
POWER SUPPLY CONNECTIONS WARNING! INSTALL THE FUSE AT THE BATTERY LAST! Use conventional stranded copper wire for all connections. Finish the ends of the wires at the amp and vehicle connection with proper size terminals. Poorly made connections, and /or inadequate wire size will generate excessive heat and may lead to equipment failure. The 12 VOLT + connection should be made directly at the positive battery post using the wire size recommended below and fused within 18 of the battery.
POWER CONNECTIONS @ ~ O@ eRo~~~~~:~~ ..~~~~~ i ~. ~~ ~~~~ ... 8 REM GND •12V ....:::> 1: ~ 'V 'V ~ @ a:: w 3: + +o. ...0 v _ In· line rowPr Fu'>e Mo unted W1th1n 1r From BattE>ry Recornmf'nded Turn on Rem ote c::ED c=::Jc=::J 0 i!!lllll IMPORTANT! Before making any connections, disconnect the car's battery until the installation is completed to avoid possible damage to the electrical system.
SPEAKER CONNECT ION- MXA4.480 SPEAKER CONNECT ION- MXA 5. 750 16-MXA5.750 SPEAKER CONNECT ION- MXA1.500 ' I - - ~'~. :·:.:::_·..·:.- ~ ~ ~ ~ ~-..,.,; Please note that the MXA 1.500 uses 2 positive and 2 negative terminals for the speaker outputs. These are provided to make it easier to put multiple subwoofers on the amplifier. The connections go to the same point inside the amplifier. CAUTION Always check your speaker load with a multi-meter before connecting the amplifier.
SET UP AND ADJUSTMENT Gain The gain control is NOT a volume control. The gain control adjusts the amount of signal required to drive the amp to full output. With the gain control at maximum (full clockwise rotation), less signal input voltage is required to drive the amp to full output. With the gain control at minimum (full counter clockwise rotation), more signal input voltage is required to drive the amp to full output.
TROUBLESHOOTING Before removing your amplifier, refer to the list below and follow the suggested procedure. Speakers and speaker wires/connections should be tested first. No Output: a. Confirm that all wiring is firmly connected. b. Both "12V"and "REM"terminals must have +12 Volts present and "GND" must be connected to chassis ground or the negative terminal of the battery. c. Confirm that signal source is connected and is supplying output signal.
SPECIFIC ATIONS 16-MXA5.750 16-MXA1.500 16-MXA4.480 n 250Wx1 80Wx4 80Wx4 +200Wx1 RMS Power 2 n 350Wx1 120Wx4 120Wx4+350Wx1 RMS Power 1 n 500Wx1 N/A N/A N/A 240Wx2 240Wx2 + N/A 0.07%/0.05% RMS Power4 Bridged Power 4 n n 0.03% 0.07% Frequency Response 20Hz- 250Hz 20Hz- 20kHz THO at4 20Hz- 20kHz 20Hz- 250Hz Dimensions (w x h x I) 6.75"x 2"x 9" 9" 12.
801788
580W TOTAL MAXIMUM POWER OUTPUT (watts) TOTAL HARMONIC DISTORTION TEST t•JtSSI~I) 16-MXA5.
